Airworthiness Directives; Airbus Airplanes, 5728-5730 [2012-2625]

Download as PDF 5728 § 39.13 Federal Register / Vol. 77, No. 24 / Monday, February 6, 2012 / Proposed Rules [Amended] 2. The FAA amends § 39.13 by adding the following new AD: Airbus: Docket No. FAA–2012–0041; Directorate Identifier 2011–NM–167–AD. (a) Comments Due Date We must receive comments by March 22, 2012. (b) Affected ADs None. (c) Applicability This AD applies to all Airbus Model A300 B2–1C, B2K–3C, B2–203, B4–2C, B4–103, and B4–203 airplanes, certificated in any category. (d) Subject Air Transport Association (ATA) of America Code 27: Flight controls. (e) Reason This AD was prompted by analysis that in a specific failure case of the upper primary attachment of the trimmable horizontal stabilizer actuator (THSA); the THSA upper secondary attachment would engage because it could only withstand the loads for a limited period of time. We are issuing this AD to prevent failure of the secondary load path, which could result in loss of control of the airplane. (f) Compliance You are responsible for having the actions required by this AD performed within the compliance times specified, unless the actions have already been done. tkelley on DSK3SPTVN1PROD with PROPOSALS (g) Actions Within 30 months after the effective date of this AD, install 3 retention plates for the gimbal bearings on the THSA upper primary attachment, in accordance with the Accomplishment Instructions of Airbus Mandatory Service Bulletin A300–27–0204, dated March 11, 2011. (h) Other FAA AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, International Branch, ANM–116, Transport Airplane Directorate, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the International Branch, send it to ATTN: Dan Rodina, Aerospace Engineer, International Branch, ANM–116, Transport Airplane Directorate, FAA, 1601 Lind Avenue SW., Renton, Washington 98057– 3356; telephone (425) 227–2125; fax (425) 227–1149. Information may be emailed to: 9-ANM-116-AMOC-REQUESTS@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/ certificate holding district office. The AMOC VerDate Mar<15>2010 15:45 Feb 03, 2012 Jkt 226001 approval letter must specifically reference this AD. (2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service. (i) Related Information Refer to MCAI European Aviation Safety Agency (EASA) Airworthiness Directive 2011–0112, dated June 15, 2011; and Airbus Mandatory Service Bulletin A300–27–0204, dated March 11, 2011; for related information. Issued in Renton, Washington, on January 23, 2012. Kalene C. Yanamura, Acting Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. 2012–2622 Filed 2–3–12; 8:45 am] BILLING CODE 4910–13–P DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2012 0040; Directorate Identifier 2011–NM–121–AD] RIN 2120–AA64 Airworthiness Directives; Airbus Airplanes Federal Aviation Administration (FAA), DOT. ACTION: Notice of proposed rulemaking (NPRM). AGENCY: We propose to adopt a new airworthiness directive (AD) for all Airbus Model A300 series airplanes; all Model A300 B4–600, B4–600R, and F4– 600R series airplanes, and Model C4– 605R Variant F airplanes (collectively called A300–600 series airplanes). This proposed AD was prompted by reports of an inoperative fire shut-off valve (FSOV) as a result of damage due to over-length of the bonding lead. This proposed AD would require a one-time detailed inspection for length of the FSOV bonding leads and for contact or chafing of the wires, and corrective actions, if necessary. We are proposing this AD to detect and correct contact or chafing of wires and bonding leads which, if not detected could be a source of sparks in the wing trailing edge, and could lead to an uncontrolled engine fire. SUMMARY: We must receive comments on this proposed AD by March 22, 2012. DATES: PO 00000 Frm 00012 Fmt 4702 Sfmt 4702 You may send comments by any of the following methods: • Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments. • Fax: (202) 493–2251. • Mail: U.S. Department of Transportation, Docket Operations, M–30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE., Washington, DC 20590. • Hand Delivery: U.S. Department of Transportation, Docket Operations, M–30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE., Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. For service information identified in this proposed AD, contact Airbus SAS– EAW (Airworthiness Office), 1 Rond Point Maurice Bellonte, 31707 Blagnac Cedex, France; telephone +33 5 61 93 36 96; fax +33 5 61 93 44 51; email: account.airworth-eas@airbus.com; Internet https://www.airbus.com. You may review copies of the referenced service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, Washington. For information on the availability of this material at the FAA, call (425) 227– 1221. ADDRESSES: Examining the AD Docket You may examine the AD docket on the Internet at https:// www.regulations.gov; or in person at the Docket Operations office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this proposed AD, the regulatory evaluation, any comments received, and other information. The street address for the Docket Operations office (telephone (800) 647–5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt. FOR FURTHER INFORMATION CONTACT: Dan Rodina, Aerospace Engineer, International Branch, ANM–116, Transport Airplane Directorate, FAA, 1601 Lind Avenue SW., Renton, Washington 98057–3356; telephone (425) 227–2125; fax (425) 227–1149. SUPPLEMENTARY INFORMATION: Comments Invited We invite you to send any written relevant data, views, or arguments about this proposed AD. Send your comments to an address listed under the ADDRESSES section. Include ‘‘Docket No. FAA–2012–0040; Directorate Identifier 2011–NM–121–AD’’ at the beginning of your comments. We specifically invite comments on the overall regulatory, E:\FR\FM\06FEP1.SGM 06FEP1 Federal Register / Vol. 77, No. 24 / Monday, February 6, 2012 / Proposed Rules economic, environmental, and energy aspects of this proposed AD. We will consider all comments received by the closing date and may amend this proposed AD based on those comments. We will post all comments we receive, without change, to https:// www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive about this proposed AD. Discussion The European Aviation Safety Agency (EASA), which is the Technical Agent for the Member States of the European Community, has issued EASA AD 2011– 0084, dated May 24, 2011 (referred to after this as ‘‘the MCAI’’), to correct an unsafe condition for the specified products. The MCAI states: During a scheduled maintenance check, one operator reported inoperative FSOV [fire shut-off valve]. Investigations showed damage at wire located between engine 2 Hydraulic FSOV and wing rear spar, in the zones 575/675, and at bonding lead, located between wing Rib 7A and Rib 8 below Hydraulic Pressure Lines. Similar inspections on different aeroplanes have shown that one of the causes of damage, is the contact between bonding lead and the harness, due to over length of the bonding lead. As the affected wire is not powered during normal operation, no defect had been detected. The defect was detected when a test was performed on the FSOV during maintenance check by the operator. This condition, in the scope of published FAA SFAR88 and JAA Internal Policy INT/ POL/25/12, is considered to be a potential source of sparks in the wing trailing edge area and if not detected, could lead to an uncontrolled engine fire. For the reasons stated above, this [EASA] AD requires a one-time [detailed] inspection of the wires [for contact or chafing] located between LH/RH engines Hydraulic FSOV and wing rear spar in the zones 575/675, and the bonding lead [for length] that is located between Rib 7A and Rib 8 below Hydraulic Pressure Lines, and corrective actions [repair wires or replace bonding leads] depending on findings. You may obtain further information by examining the MCAI in the AD docket. tkelley on DSK3SPTVN1PROD with PROPOSALS Relevant Service Information Airbus has issued Mandatory Service Bulletins A300–24–0106 (for Model A300 series airplanes); and A300–24– 6108 (for Model A300–600 series airplanes); both including Appendices 01 and 02, both dated July 9, 2010. The actions described in this service information are intended to correct the unsafe condition identified in the MCAI. VerDate Mar<15>2010 15:45 Feb 03, 2012 Jkt 226001 FAA’s Determination and Requirements of This Proposed AD This product has been approved by the aviation authority of another country, and is approved for operation in the United States. Pursuant to our bilateral agreement with the State of Design Authority, we have been notified of the unsafe condition described in the MCAI and service information referenced above. We are proposing this AD because we evaluated all pertinent information and determined an unsafe condition exists and is likely to exist or develop on other products of the same type design. Costs of Compliance Based on the service information, we estimate that this proposed AD would affect about 125 products of U.S. registry. We also estimate that it would take about 8 work-hours per product to comply with the basic requirements of this proposed AD. The average labor rate is $85 per work-hour. Based on these figures, we estimate the cost of the proposed AD on U.S. operators to be $85,000, or $680 per product. In addition, we estimate that any necessary follow-on actions would take about 1 work-hour and require parts costing $50, for a cost of $135 per product. We have no way of determining the number of products that may need these actions. Authority for This Rulemaking Title 49 of the United States Code specifies the FAA’s authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. ‘‘Subtitle VII: Aviation Programs,’’ describes in more detail the scope of the Agency’s authority. We are issuing this rulemaking under the authority described in ‘‘Subtitle VII, Part A, Subpart III, Section 44701: General requirements.’’ Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. Regulatory Findings We determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national PO 00000 Frm 00013 Fmt 4702 Sfmt 4702 5729 Government and the States, or on the distribution of power and responsibilities among the various levels of government. For the reasons discussed above, I certify this proposed regulation: 1. Is not a ‘‘significant regulatory action’’ under Executive Order 12866; 2. Is not a ‘‘significant rule’’ under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); 3. Will not affect intrastate aviation in Alaska; and 4. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. We prepared a regulatory evaluation of the estimated costs to comply with this proposed AD and placed it in the AD docket. List of Subjects in 14 CFR Part 39 Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety. The Proposed Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows: PART 39—AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. § 39.13 [Amended] 2. The FAA amends § 39.13 by adding the following new AD: Airbus: Docket No. FAA–2012–0040; Directorate Identifier 2011–NM–121–AD. (a) Comments Due Date We must receive comments by March 22, 2012. (b) Affected ADs None. (c) Applicability This AD applies to airplanes specified in paragraphs (c)(1), (c)(2) and (c)(3) of this AD; certificated in any category; all certificated models; all serial numbers. (1) Airbus Model A300 B2–1A, B2–1C, B2K–3C, B2–203, B4–2C, B4–103, and B4– 203 airplanes. (2) Airbus Model A300 B4–601, B4–603, B4–620, B4–622, B4–605R, B4–622R, F4– 605R, and F4–622 airplanes. (3) Airbus Model A300 C4–605R Variant F airplanes. (d) Subject Air Transport Association (ATA) of America Code 24: Electrical Power. E:\FR\FM\06FEP1.SGM 06FEP1 5730 Federal Register / Vol. 77, No. 24 / Monday, February 6, 2012 / Proposed Rules (e) Reason This AD was prompted by reports of an inoperative fire shut-off valve (FSOV) as a result of damage due to over-length of the bonding lead. We are issuing this AD to detect and correct contact or chafing of wires and bonding leads which, if not detected, could be a source of sparks in the wing trailing edge, and could lead to an uncontrolled engine fire. (f) Compliance You are responsible for having the actions required by this AD performed within the compliance times specified, unless the actions have already been done. (g) Inspection of the FSOV Bonding Leads Within 4,500 flight hours or 30 months after the effective date of this AD, whichever occurs first: Do a one-time detailed inspection for length of the FSOV bonding leads, and for contact or chafing of the wires located on left hand (LH) side and right-hand (RH) side of the wing rear spar, in accordance with Accomplishment Instructions of the Airbus Mandatory Service Bulletin A300–24– 0106, dated July 9, 2010 (for Model A300 series airplanes); or Airbus Mandatory Service Bulletin A300–24–6108, dated July 9, 2010 (for Model A300–600 series airplanes). request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the International Branch, send it to ATTN: Dan Rodina, Aerospace Engineer, International Branch, ANM–116, Transport Airplane Directorate, FAA, 1601 Lind Avenue SW., Renton, Washington 98057– 3356; telephone (425) 227–2125; fax (425) 227–1149. (2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service. (l) Related Information Refer to MCAI European Aviation Safety Agency (EASA) Airworthiness Directive 2011–0084, dated May 24, 2011; and the service information identified in paragraphs (l)(1), and (l)(2) of this AD; for related information. (1) Airbus Mandatory Service Bulletin A300–24–0106, dated July 9, 2010. (2) Airbus Mandatory Service Bulletin A300–24–6108, dated July 9, 2010. (h) Corrective Action for FSOV Bonding Leads If, during the inspection required by paragraph (g) of this AD, the length of the bonding lead(s) is more than 80 mm (3.15 inches), before further flight, replace the bonding lead(s) with a new bonding lead having a length equal to 80 mm (3.15 inches), in accordance with the Accomplishment Instructions of Airbus Mandatory Service Bulletin A300–24–0106, dated July 9, 2010 (for Model A300 series airplanes); or Airbus Mandatory Service Bulletin A300–24–6108, dated July 9, 2010 (for Model A300–600 series airplanes). Issued in Renton, Washington, on January 12, 2012. Michael J. Kaszycki, Acting Manager, Transport Airplane Directorate, Aircraft Certification Service. (i) Repair of the Wires of the LH and RH Sides If, during the inspection required by paragraph (g) of this AD, contact(s) or chafing(s) of the wires is found, repair the wires in accordance with the Accomplishment Instructions of Airbus Mandatory Service Bulletin A300–24–0106, dated July 9, 2010 (for Model A300 series airplanes); or Airbus Mandatory Service Bulletin A300–24–6108, dated July 9, 2010 (for Model A300–600 series airplanes). [Docket No. FAA–2012–0042; Directorate Identifier 2011–NM–154–AD] tkelley on DSK3SPTVN1PROD with PROPOSALS (j) Parts Installation As of the effective date of this AD, no person may install any bonding lead longer than 80 mm (3.15 inches), located between LH/RH engine hydraulic FSOV and wing rear spar in the zones 575/675 on any airplane. (k) Other FAA AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, International Branch, ANM–116, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your VerDate Mar<15>2010 18:22 Feb 03, 2012 Jkt 226001 [FR Doc. 2012–2625 Filed 2–3–12; 8:45 am] BILLING CODE 4910–13–P DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 RIN 2120–AA64 Airworthiness Directives; Bombardier, Inc. Airplanes Federal Aviation Administration (FAA), DOT. ACTION: Notice of proposed rulemaking (NPRM). AGENCY: We propose to supersede an existing airworthiness directive (AD) that applies to certain Bombardier, Inc. Model CL–600–2C10 (Regional Jet Series 700, 701 & 702), CL–600–2D15 (Regional Jet Series 705), and CL–600– 2D24 (Regional Jet Series 900) airplanes. The existing AD currently requires a one-time inspection of the main landing gear (MLG) shock strut assemblies for part and serial numbers; for certain MLG shock strut assemblies, a one-time inspection of the torque link apex joint, and corrective actions if necessary; and, SUMMARY: PO 00000 Frm 00014 Fmt 4702 Sfmt 4702 for certain MLG shock strut assemblies, replacement or rework of the apex nut. Since we issued that AD, we have determined that part and serial numbers for MLG shock strut assemblies for Model CL–600–2D15 and CL–600–2D24 airplanes were inadvertently omitted from certain requirements of the existing AD. This proposed AD would continue to require the actions in the existing AD, and would add the previously omitted part and serial numbers. We are proposing this AD to detect and correct improper assembly and damage of the MLG torque link apex joint, which could cause heavy vibration during landing, consequent damage to MLG components, and subsequent collapse of the MLG. DATES: We must receive comments on this proposed AD by March 22, 2012. ADDRESSES: You may send comments by any of the following methods: • Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments. • Fax: (202) 493–2251. • Mail: U.S. Department of Transportation, Docket Operations, M–30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE., Washington, DC 20590. • Hand Delivery: U.S. Department of Transportation, Docket Operations, M–30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE., Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. For service information identified in this proposed AD, contact Bombardier, Inc., 400 Cote-Vertu Road West, Dorval, Quebec H4S 1Y9, Canada; phone: 514– 855–5000; fax: 514–855–7401; email: thd.crj@aero.bombardier.com; Internet: https://www.bombardier.com. You may review copies of the referenced service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, Washington. For information on the availability of this material at the FAA, call (425) 227– 1221. Examining the AD Docket You may examine the AD docket on the Internet at https:// www.regulations.gov; or in person at the Docket Operations office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this proposed AD, the regulatory evaluation, any comments received, and other information. The street address for the Docket Operations office (telephone (800) 647–5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt. E:\FR\FM\06FEP1.SGM 06FEP1

Agencies

[Federal Register Volume 77, Number 24 (Monday, February 6, 2012)]
[Proposed Rules]
[Pages 5728-5730]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2012-2625]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2012 0040; Directorate Identifier 2011-NM-121-AD]
RIN 2120-AA64


Airworthiness Directives; Airbus Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for all 
Airbus Model A300 series airplanes; all Model A300 B4-600, B4-600R, and 
F4-600R series airplanes, and Model C4-605R Variant F airplanes 
(collectively called A300-600 series airplanes). This proposed AD was 
prompted by reports of an inoperative fire shut-off valve (FSOV) as a 
result of damage due to over-length of the bonding lead. This proposed 
AD would require a one-time detailed inspection for length of the FSOV 
bonding leads and for contact or chafing of the wires, and corrective 
actions, if necessary. We are proposing this AD to detect and correct 
contact or chafing of wires and bonding leads which, if not detected 
could be a source of sparks in the wing trailing edge, and could lead 
to an uncontrolled engine fire.

DATES: We must receive comments on this proposed AD by March 22, 2012.

ADDRESSES: You may send comments by any of the following methods:
     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: (202) 493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC, between 9 a.m. and 5 p.m., Monday 
through Friday, except Federal holidays.
    For service information identified in this proposed AD, contact 
Airbus SAS-EAW (Airworthiness Office), 1 Rond Point Maurice Bellonte, 
31707 Blagnac Cedex, France; telephone +33 5 61 93 36 96; fax +33 5 61 
93 44 51; email: account.airworth-eas@airbus.com; Internet https://www.airbus.com. You may review copies of the referenced service 
information at the FAA, Transport Airplane Directorate, 1601 Lind 
Avenue SW., Renton, Washington. For information on the availability of 
this material at the FAA, call (425) 227-1221.

Examining the AD Docket

    You may examine the AD docket on the Internet at https://www.regulations.gov; or in person at the Docket Operations office 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The AD docket contains this proposed AD, the regulatory 
evaluation, any comments received, and other information. The street 
address for the Docket Operations office (telephone (800) 647-5527) is 
in the ADDRESSES section. Comments will be available in the AD docket 
shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Dan Rodina, Aerospace Engineer, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
1601 Lind Avenue SW., Renton, Washington 98057-3356; telephone (425) 
227-2125; fax (425) 227-1149.

SUPPLEMENTARY INFORMATION: 

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposed AD. Send your comments to an address 
listed under the ADDRESSES section. Include ``Docket No. FAA-2012-0040; 
Directorate Identifier 2011-NM-121-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory,

[[Page 5729]]

economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD based on those comments.
    We will post all comments we receive, without change, to https://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact we 
receive about this proposed AD.

Discussion

    The European Aviation Safety Agency (EASA), which is the Technical 
Agent for the Member States of the European Community, has issued EASA 
AD 2011-0084, dated May 24, 2011 (referred to after this as ``the 
MCAI''), to correct an unsafe condition for the specified products. The 
MCAI states:

    During a scheduled maintenance check, one operator reported 
inoperative FSOV [fire shut-off valve]. Investigations showed damage 
at wire located between engine 2 Hydraulic FSOV and wing rear spar, 
in the zones 575/675, and at bonding lead, located between wing Rib 
7A and Rib 8 below Hydraulic Pressure Lines.
    Similar inspections on different aeroplanes have shown that one 
of the causes of damage, is the contact between bonding lead and the 
harness, due to over length of the bonding lead.
    As the affected wire is not powered during normal operation, no 
defect had been detected. The defect was detected when a test was 
performed on the FSOV during maintenance check by the operator.
    This condition, in the scope of published FAA SFAR88 and JAA 
Internal Policy INT/POL/25/12, is considered to be a potential 
source of sparks in the wing trailing edge area and if not detected, 
could lead to an uncontrolled engine fire.
    For the reasons stated above, this [EASA] AD requires a one-time 
[detailed] inspection of the wires [for contact or chafing] located 
between LH/RH engines Hydraulic FSOV and wing rear spar in the zones 
575/675, and the bonding lead [for length] that is located between 
Rib 7A and Rib 8 below Hydraulic Pressure Lines, and corrective 
actions [repair wires or replace bonding leads] depending on 
findings.

    You may obtain further information by examining the MCAI in the AD 
docket.

Relevant Service Information

    Airbus has issued Mandatory Service Bulletins A300-24-0106 (for 
Model A300 series airplanes); and A300-24-6108 (for Model A300-600 
series airplanes); both including Appendices 01 and 02, both dated July 
9, 2010. The actions described in this service information are intended 
to correct the unsafe condition identified in the MCAI.

FAA's Determination and Requirements of This Proposed AD

    This product has been approved by the aviation authority of another 
country, and is approved for operation in the United States. Pursuant 
to our bilateral agreement with the State of Design Authority, we have 
been notified of the unsafe condition described in the MCAI and service 
information referenced above. We are proposing this AD because we 
evaluated all pertinent information and determined an unsafe condition 
exists and is likely to exist or develop on other products of the same 
type design.

Costs of Compliance

    Based on the service information, we estimate that this proposed AD 
would affect about 125 products of U.S. registry. We also estimate that 
it would take about 8 work-hours per product to comply with the basic 
requirements of this proposed AD. The average labor rate is $85 per 
work-hour. Based on these figures, we estimate the cost of the proposed 
AD on U.S. operators to be $85,000, or $680 per product.
    In addition, we estimate that any necessary follow-on actions would 
take about 1 work-hour and require parts costing $50, for a cost of 
$135 per product. We have no way of determining the number of products 
that may need these actions.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. ``Subtitle VII: Aviation 
Programs,'' describes in more detail the scope of the Agency's 
authority.
    We are issuing this rulemaking under the authority described in 
``Subtitle VII, Part A, Subpart III, Section 44701: General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify this proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);
    3. Will not affect intrastate aviation in Alaska; and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a regulatory evaluation of the estimated costs to 
comply with this proposed AD and placed it in the AD docket.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

    1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

    2. The FAA amends Sec.  39.13 by adding the following new AD:

Airbus: Docket No. FAA-2012-0040; Directorate Identifier 2011-NM-
121-AD.

(a) Comments Due Date

    We must receive comments by March 22, 2012.

(b) Affected ADs

    None.

(c) Applicability

    This AD applies to airplanes specified in paragraphs (c)(1), 
(c)(2) and (c)(3) of this AD; certificated in any category; all 
certificated models; all serial numbers.
    (1) Airbus Model A300 B2-1A, B2-1C, B2K-3C, B2-203, B4-2C, B4-
103, and B4-203 airplanes.
    (2) Airbus Model A300 B4-601, B4-603, B4-620, B4-622, B4-605R, 
B4-622R, F4-605R, and F4-622 airplanes.
    (3) Airbus Model A300 C4-605R Variant F airplanes.

(d) Subject

    Air Transport Association (ATA) of America Code 24: Electrical 
Power.

[[Page 5730]]

(e) Reason

    This AD was prompted by reports of an inoperative fire shut-off 
valve (FSOV) as a result of damage due to over-length of the bonding 
lead. We are issuing this AD to detect and correct contact or 
chafing of wires and bonding leads which, if not detected, could be 
a source of sparks in the wing trailing edge, and could lead to an 
uncontrolled engine fire.

(f) Compliance

    You are responsible for having the actions required by this AD 
performed within the compliance times specified, unless the actions 
have already been done.

(g) Inspection of the FSOV Bonding Leads

    Within 4,500 flight hours or 30 months after the effective date 
of this AD, whichever occurs first: Do a one-time detailed 
inspection for length of the FSOV bonding leads, and for contact or 
chafing of the wires located on left hand (LH) side and right-hand 
(RH) side of the wing rear spar, in accordance with Accomplishment 
Instructions of the Airbus Mandatory Service Bulletin A300-24-0106, 
dated July 9, 2010 (for Model A300 series airplanes); or Airbus 
Mandatory Service Bulletin A300-24-6108, dated July 9, 2010 (for 
Model A300-600 series airplanes).

(h) Corrective Action for FSOV Bonding Leads

    If, during the inspection required by paragraph (g) of this AD, 
the length of the bonding lead(s) is more than 80 mm (3.15 inches), 
before further flight, replace the bonding lead(s) with a new 
bonding lead having a length equal to 80 mm (3.15 inches), in 
accordance with the Accomplishment Instructions of Airbus Mandatory 
Service Bulletin A300-24-0106, dated July 9, 2010 (for Model A300 
series airplanes); or Airbus Mandatory Service Bulletin A300-24-
6108, dated July 9, 2010 (for Model A300-600 series airplanes).

(i) Repair of the Wires of the LH and RH Sides

    If, during the inspection required by paragraph (g) of this AD, 
contact(s) or chafing(s) of the wires is found, repair the wires in 
accordance with the Accomplishment Instructions of Airbus Mandatory 
Service Bulletin A300-24-0106, dated July 9, 2010 (for Model A300 
series airplanes); or Airbus Mandatory Service Bulletin A300-24-
6108, dated July 9, 2010 (for Model A300-600 series airplanes).

(j) Parts Installation

    As of the effective date of this AD, no person may install any 
bonding lead longer than 80 mm (3.15 inches), located between LH/RH 
engine hydraulic FSOV and wing rear spar in the zones 575/675 on any 
airplane.

(k) Other FAA AD Provisions

    The following provisions also apply to this AD:
    (1) Alternative Methods of Compliance (AMOCs): The Manager, 
International Branch, ANM-116, FAA, has the authority to approve 
AMOCs for this AD, if requested using the procedures found in 14 CFR 
39.19. In accordance with 14 CFR 39.19, send your request to your 
principal inspector or local Flight Standards District Office, as 
appropriate. If sending information directly to the International 
Branch, send it to ATTN: Dan Rodina, Aerospace Engineer, 
International Branch, ANM-116, Transport Airplane Directorate, FAA, 
1601 Lind Avenue SW., Renton, Washington 98057-3356; telephone (425) 
227-2125; fax (425) 227-1149.
    (2) Airworthy Product: For any requirement in this AD to obtain 
corrective actions from a manufacturer or other source, use these 
actions if they are FAA-approved. Corrective actions are considered 
FAA-approved if they are approved by the State of Design Authority 
(or their delegated agent). You are required to assure the product 
is airworthy before it is returned to service.

(l) Related Information

    Refer to MCAI European Aviation Safety Agency (EASA) 
Airworthiness Directive 2011-0084, dated May 24, 2011; and the 
service information identified in paragraphs (l)(1), and (l)(2) of 
this AD; for related information.
    (1) Airbus Mandatory Service Bulletin A300-24-0106, dated July 
9, 2010.
    (2) Airbus Mandatory Service Bulletin A300-24-6108, dated July 
9, 2010.

    Issued in Renton, Washington, on January 12, 2012.
Michael J. Kaszycki,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2012-2625 Filed 2-3-12; 8:45 am]
BILLING CODE 4910-13-P
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.