Airworthiness Directives; Eurocopter Deutschland GmbH Helicopters, 76068-76070 [2011-31254]

Download as PDF 76068 Federal Register / Vol. 76, No. 234 / Tuesday, December 6, 2011 / Proposed Rules structural damage significant enough to result in loss of control of the airplane. (j) Alternative Methods of Compliance (AMOCs) DEPARTMENT OF TRANSPORTATION (f) Compliance (1) The Manager, Seattle Aircraft Certification Office (ACO), FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the manager of the ACO, send it to the attention of the person identified in the Related Information section of this AD. Information may be emailed to: 9-ANMSeattle-ACO-AMOC-Requests@faa.gov. (2) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/ certificate holding district office. (3) An AMOC that provides an acceptable level of safety may be used for any repair required by this AD if it is approved by the Boeing Commercial Airplanes Organization Designation Authorization (ODA) that has been authorized by the Manager, Seattle ACO, to make those findings. For a repair method to be approved, the repair must meet the certification basis of the airplane, and the approval must specifically refer to this AD. Federal Aviation Administration Comply with this AD within the compliance times specified, unless already done. (g) Pivot Pin Replacement At the applicable time specified in paragraph 1.E., ‘‘Compliance,’’ of Boeing Alert Service Bulletin 777–55A0018, dated July 27, 2011, except as required by paragraph (i)(2) of this AD, replace the pivot pins of the horizontal stabilizer with new or reworked pivot pins, including replacing the spacer with a new spacer or with one that has been determined to be without corrosion damage or other irregularities; in accordance with the Accomplishment Instructions of Boeing Alert Service Bulletin 777–55A0018, dated July 27, 2011. (h) Repetitive Inspections At the applicable time specified in paragraph 1.E., ‘‘Compliance,’’ of Boeing Alert Service Bulletin 777–55A0018, dated July 27, 2011: Do detailed inspections for cracks, corrosion damage, or other irregularity of the outer and inner pivot pins; and an ultrasonic inspection for cracking of the outer pivot pins; and do all applicable corrective actions; in accordance with the Accomplishment Instructions of Boeing Alert Service Bulletin 777–55A0018, dated July 27, 2011. Corrective actions must be done before further flight. Repeat the inspections at the applicable interval specified in paragraph 1.E., ‘‘Compliance,’’ of Boeing Alert Service Bulletin 777–55A0018, dated July 27, 2011, except as provided by paragraph (i)(1) of this AD. Note 1: The Accomplishment Instructions of Boeing Alert Service Bulletin 777– 55A0018, dated July 27, 2011, might refer to other procedures. When the words ‘‘refer to’’ are used and the operator has an accepted alternative procedure, the accepted alternative procedure can be used to comply with the AD. When the words ‘‘in accordance with’’ are included in the instruction, the procedure in the design approval holder document must be used to comply with the AD. tkelley on DSK3SPTVN1PROD with PROPOSALS-1 (i) Exceptions The following exceptions to Boeing Alert Service Bulletin 777–55A0018, dated July 27, 2011, apply to this AD. (1) Where the Repeat Interval column of tables 2 and 3 of paragraph 1.E., ‘‘Compliance,’’ of Boeing Alert Service Bulletin 777–55A0018, dated July 27, 2011, specify a compliance time, this AD requires compliance within the specified compliance time after the most recent inspection. (2) Where paragraph 1.E., ‘‘Compliance,’’ of Boeing Alert Service Bulletin 777–55A0018, dated July 27, 2011, specifies a compliance time ‘‘after the original issue date of this service bulletin,’’ this AD requires compliance within the specified compliance time ‘‘after the effective date of this AD.’’ VerDate Mar<15>2010 15:26 Dec 05, 2011 Jkt 226001 14 CFR Part 39 [Docket No. FAA–2011–1285; Directorate Identifier 2010–SW–073–AD] RIN 2120–AA64 Airworthiness Directives; Eurocopter Deutschland GmbH Helicopters Federal Aviation Administration (FAA), DOT. ACTION: Notice of proposed rulemaking (NPRM). AGENCY: We propose to adopt a new airworthiness directive (AD) for Eurocopter Deutschland GmbH Model BO–105A, BO–105C, BO–105LS A–1, BO–105LS A–3, and BO–105S helicopters. This proposed AD would require inspecting certain main rotor blades for debonding of the erosion protective shell. If the erosion protective shell is debonded, you would be required to replace the main rotor blade with an airworthy main rotor blade. This proposed AD is prompted by the results of an inspection on a BO–105 (k) Related Information helicopter where debonding was (1) For more information about this AD, discovered on a main rotor blade contact James Sutherland, Aerospace erosion protective shell, and it was Engineer, Airframe Branch, ANM–120S, determined that the debonding was due FAA, Seattle Aircraft Certification Office, to incorrect installation of the erosion 1601 Lind Avenue SW., Renton, Washington protective shell. Subsequently, an 98057–3356; phone: (425) 917–6533; fax: incident occurred where a BO–105 (425) 917–6590; email: helicopter lost its main rotor blade james.sutherland@faa.gov. erosion protective shell during flight. (2) For service information identified in The actions specified by this proposed this AD, contact Boeing Commercial AD are intended to detect debonding of Airplanes, Attention: Data & Services the main rotor blade erosion protective Management, P.O. Box 3707, MC 2H–65, shell which could lead to an unbalanced Seattle, Washington 98124–2207; telephone main rotor, high vibrations, damage to (206) 544–5000, extension 1; fax (206) 766– 5680; email me.boecom@boeing.com; Internet the tail boom or tail rotor, and loss of control of the helicopter. https://www.myboeingfleet.com. You may review copies of the referenced service DATES: Comments must be received on information at the FAA, Transport Airplane or before February 6, 2012. Directorate, 1601 Lind Avenue SW., Renton, ADDRESSES: Use one of the following Washington. For information on the addresses to submit comments on this availability of this material at the FAA, call proposed AD: (425) 227–1221. • Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the Issued in Renton, Washington, on instructions for submitting comments. November 23, 2011. • Fax: (202) 493–2251. Ali Bahrami, • Mail: U.S. Department of Manager, Transport Airplane Directorate, Transportation, Docket Operations, M– Aircraft Certification Service. 30, West Building Ground Floor, Room [FR Doc. 2011–31312 Filed 12–5–11; 8:45 am] W12–140, 1200 New Jersey Avenue SE., BILLING CODE 4910–13–P Washington, DC 20590. • Hand Delivery: U.S. Department of Transportation, Docket Operations, M– 30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE., Washington, DC 20590, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. PO 00000 Frm 00003 Fmt 4702 Sfmt 4702 SUMMARY: E:\FR\FM\06DEP1.SGM 06DEP1 Federal Register / Vol. 76, No. 234 / Tuesday, December 6, 2011 / Proposed Rules You may get the service information identified in this proposed AD from American Eurocopter Corporation, 2701 N. Forum Drive, Grand Prairie, TX 75052, telephone (972) 641–0000 or (800) 232–0323, fax (972) 641–3775, or at https://www.eurocopter.com/techpub. FOR FURTHER INFORMATION CONTACT: Jim Grigg, Manager, FAA, Rotorcraft Directorate, Safety Management Group, 2601 Meacham Blvd., Fort Worth, TX 76137, telephone (817) 222–5126, fax (817) 222–5961. SUPPLEMENTARY INFORMATION: tkelley on DSK3SPTVN1PROD with PROPOSALS-1 Comments Invited We invite you to send any written relevant data, views, or arguments about this proposed AD. Send your comments to an address listed under the caption ADDRESSES. Include the Docket No. ‘‘FAA–2011–1285, Directorate Identifier 2010–SW–073–AD’’ at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this proposed AD. We will consider all comments received by the closing date and may amend this proposed AD because of those comments. We will post all comments we receive, without change, to https:// www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact with FAA personnel concerning this proposed rulemaking. Using the search function of the docket web site, you can find and read the comments to any of our dockets, including the name of the individual who sent or signed the comment. You may review the DOT’s complete Privacy Act Statement in the Federal Register published on April 11, 2000 (65 FR 19477–78). Examining the Docket You may examine the docket that contains the proposed AD, any comments, and other information in person at the Docket Operations office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The Docket Operations office (telephone (800) 647–5527) is located in Room W12–140 on the ground floor of the West Building at the street address stated in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt. Discussion The European Aviation Safety Agency (EASA), which is the Technical Agent for the Member States of the European Community, has issued Emergency AD No. 2010–0216–E, dated October 21, VerDate Mar<15>2010 15:26 Dec 05, 2011 Jkt 226001 2010 (corrected October 29, 2010), to correct an unsafe condition for Eurocopter Deutschland Model BO– 105A, BO–105C, BO–105D, BO–105LS A–1, BO–105LS A–3, and BO–105S helicopters, all variants (except CB–5 and DBS–5, which are military models.) EASA advises that during an inspection on a BO–105 helicopter, debonding was found on the erosion protective shell of a main rotor blade, and it was determined that the debonding was caused by incorrect installation of the erosion protective shell. In addition, EASA states that an incident occurred where a second BO–105 helicopter lost its erosion protective shell during flight. EASA advises that this condition, if not detected, could result in loss of the main rotor blade erosion protective shell during flight, leading to an unbalanced main rotor and high vibrations, which could result in damage to the tail boom or tail rotor, loss of tail rotor control, and loss of control of the helicopter. Related Service Information Eurocopter Deutschland has issued Emergency Alert Service Bulletin No. BO105–10–124, dated July 14, 2010, for the Model BO105 helicopter, with a main rotor blade, part number (P/N) 105–15103, 105–15141, 105– 15141V001, 105–15143, 105–15150, 105–15150V001, 105–15152, 105– 81013, 105–87214, 1120–15101, or 1120–15103, where the main rotor blade erosion protective shell was replaced between September 2006 and March 2010. Eurocopter Deutschland also issued Emergency Alert Service Bulletin BO105LS–10–12 for the Model BO105LS A–3 helicopter, dated July 14, 2010, with a main rotor blade, part P/ N 105–15141, where the main rotor blade erosion protective shell was replaced between September 2006 and March 2010. Both Emergency Alert Service Bulletins specified a one-time inspection of the main rotor blades within the next 50 flight hours to determine if debonding of the main rotor blade erosion protective shell has occurred. Both Service Bulletins exclude helicopters from this inspection if each main rotor blade was inspected at the last 600 flight hour inspection and no debonding was detected during the inspection. In response to the incident where the helicopter lost its main rotor blade erosion protective shell during flight, Eurocopter Deutschland has issued Emergency Alert Service Bulletin No. BO105–10–124, Revision 1, dated October 18, 2010, and Emergency Alert Service Bulletin BO105LS–10–12, Revision 1, dated October 20, 2010. These Service Bulletins specify the PO 00000 Frm 00004 Fmt 4702 Sfmt 4702 76069 same inspection requirements as the original Service Bulletins, but revise the inspection compliance time from 50 flight hours to 10 flight hours. EASA classified these Service Bulletins as mandatory, and issued EASA Emergency AD No. 2010–0216–E, dated October 21, 2010 (corrected October 29, 2010) to ensure the continued airworthiness of these helicopters. FAA’s Evaluation and Unsafe Condition Determination These products have been approved by the aviation authority of Germany and are approved for operation in the United States. Pursuant to our bilateral agreement with Germany, EASA, their technical representative, has notified us of the unsafe condition described in their AD. We are proposing this AD because we evaluated all information provided by EASA and determined the unsafe condition exists and is likely to exist or develop on other products of these same type designs. This proposed AD would require a one-time inspection of each main rotor blade for debonding of the main rotor blade erosion protective shell within 50 hours time-inservice (TIS), for helicopters with a main rotor blade, P/N 105–15103, 105– 15141, 105–15141V001, 105–15143, 105–15150, 105–15150V001, 105– 15152, 105–81013, 105–87214, 1120– 15101, or 1120–15103, where the main rotor blade erosion protective shell was replaced between September 2006 and March 2010. If debonding is detected during the inspection, before further flight, you would be required to replace the main rotor blade with an airworthy main rotor blade. Differences Between This Proposed AD and the EASA AD The differences between this proposed AD and the EASA AD are: • This proposed AD uses the term ‘‘hours time-in-service’’ to describe compliance times, and the EASA AD uses ‘‘flight hours.’’ • The EASA AD allows compliance within ‘‘10 flight hours, or 4 flight cycles, or 4 weeks, whichever occurs first,’’ and this proposed AD would require compliance within 50 hours TIS. • The EASA AD allows you to replace the main rotor blade erosion protective shell if debonding is detected, and this proposed AD would require you to replace the main rotor blade with an airworthy main rotor blade if debonding is detected. • The EASA AD is applicable to the Model BO–105D helicopter, and this proposed AD does not include this model because it does not have a typecertificate in the U.S. E:\FR\FM\06DEP1.SGM 06DEP1 76070 Federal Register / Vol. 76, No. 234 / Tuesday, December 6, 2011 / Proposed Rules Costs of Compliance We estimate that this proposed AD would affect 97 helicopters of U.S. registry. We estimate that it would take about 1.0 work-hour per helicopter to do the inspection, at an average labor rate of $85 per work hour. Based on these figures, we estimate the cost of the proposed AD on U.S. operators to be $8,245, or $85 per product. If debonding is found, we estimate that it would take about 2 work-hours to replace the main rotor blade, and required parts would cost $114,182, for a cost of $114,352. We have no way of determining how many operators would incur these costs. Regulatory Findings We have determined that this proposed AD would not have federalism implications under Executive Order 13132. Additionally, this proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government. For the reasons discussed above, I certify that the proposed regulation: 1. Is not a ‘‘significant regulatory action’’ under Executive Order 12866; 2. Is not a ‘‘significant rule’’ under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); 3. Will not affect intrastate aviation in Alaska to the extent that a regulatory distinction is required; and 4. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. We prepared an economic evaluation of the estimated costs to comply with this proposed AD. See the AD docket to examine the economic evaluation. tkelley on DSK3SPTVN1PROD with PROPOSALS-1 Authority for This Rulemaking Title 49 of the United States Code specifies the FAA’s authority to issue rules on aviation safety. Subtitle I, Section 106, describes the authority of the FAA Administrator. Subtitle VII, Aviation Programs, describes in more detail the scope of the Agency’s authority. We are issuing this rulemaking under the authority described in subtitle VII, part A, subpart III, section 44701, ‘‘General requirements.’’ Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority VerDate Mar<15>2010 15:26 Dec 05, 2011 Jkt 226001 because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. Note 2: The subject of this AD is addressed in European Aviation Safety Agency AD 2010–0216–E, dated October 21, 2010 (corrected October 29, 2010). List of Subjects in 14 CFR Part 39 Air transportation, Aircraft, Aviation safety, Incorporation by Reference, Safety. Issued in Fort Worth, Texas, on November 29, 2011. Lance T. Gant, Acting Manager, Rotorcraft Directorate, Aircraft Certification Service. The Proposed Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows: [FR Doc. 2011–31254 Filed 12–5–11; 8:45 am] BILLING CODE 4910–13–P DEPARTMENT OF TRANSPORTATION Federal Aviation Administration PART 39—AIRWORTHINESS DIRECTIVES 14 CFR Part 71 1. The authority citation for Part 39 continues to read as follows: [Docket No. FAA–2011–1193; Airspace Docket No. 11–ANM–14] Authority: 49 U.S.C. 106(g), 40113, 44701. § 39.13 [Amended] 2. Section 39.13 is amended by adding a new airworthiness directive (AD) to read as follows: Eurocopter Deutschland GMBH: Docket No. FAA–2011–1285; Directorate Identifier 2010–SW–073–AD. Applicability: Model BO–105A, BO–105C, BO–105LS A–1, BO–105LS A–3, and BO– 105S helicopters, all serial numbers, with a main rotor blade, part number (P/N) 105– 15103, 105–15141, 105–15141V001, 105– 15143, 105–15150, 105–15150V001, 105– 15152, 105–81013, 105–87214, 1120–15101, or 1120–15103; where the main rotor blade erosion protective shell was replaced between September 2006 and March 2010; certificated in any category. Compliance: Required within 50 hours time-in-service (TIS) after the effective date of this AD, unless accomplished previously. To detect debonding of the main rotor blade erosion protective shell, which could lead to an unbalanced main rotor, high vibration, damage to the tail boom or tail rotor, and loss of control of the helicopter, accomplish the following: (a) Inspect the main rotor blade for debonding of the erosion protective shell. If debonding is detected during the inspection, before further flight, replace the main rotor blade with an airworthy main rotor blade. Note 1: Eurocopter Deutschland GmbH Emergency Alert Service Bulletin No. BO105–10–124, Revision 1, dated October 18, 2010, and No. BO105LS–10–12, Revision 1, dated October 20, 2010, which are not incorporated by reference, contain additional information about the subject of this AD. (b) To request a different method of compliance or a different compliance time for this AD, follow the procedures in 14 CFR 39.19. Contact the Manager, Regulations and Policy Group, FAA, ATTN: Jim Grigg, Manager, 2601 Meacham Blvd., Fort Worth, Texas 76137; telephone: (817) 222–5122; fax: (817) 222–5126, for information about previously approved alternative methods of compliance. (c) The Joint Aircraft System/Component Code is 6210: Main Rotor Blades. PO 00000 Frm 00005 Fmt 4702 Sfmt 4702 Proposed Modification of Area Navigation Route T–288; WY Federal Aviation Administration (FAA), DOT. ACTION: Notice of proposed rulemaking (NPRM). AGENCY: This action proposes to modify low altitude area navigation (RNAV) route T–288 by extending the route westward from the Rapid City, SD, VORTAC to the Gillette, WY, VOR/ DME. The proposed extension would enhance efficiency and safety of the National Airspace System (NAS) by supplementing the existing VOR Federal airway structure in that area. DATES: Comments must be received on or before January 20, 2012. ADDRESSES: Send comments on this proposal to the Docket Management Facility, U.S. Department of Transportation, Docket Operations, M– 30, 1200 New Jersey Avenue SE., West Building Ground Floor, Room W12–140, Washington, DC 20590–0001; telephone: (202) 366–9826. You must identify FAA Docket No. FAA–2011–1193 and Airspace Docket No. 11–ANM–14 at the beginning of your comments. You may also submit comments through the Internet at https://www.regulations.gov. FOR FURTHER INFORMATION CONTACT: Paul Gallant, Airspace, Regulations and ATC Procedures Group, Office of Airspace Services, Federal Aviation Administration, 800 Independence Avenue SW., Washington, DC 20591; telephone: (202) 267–8783. SUPPLEMENTARY INFORMATION: SUMMARY: Comments Invited Interested parties are invited to participate in this proposed rulemaking by submitting such written data, views, or arguments, as they may desire. E:\FR\FM\06DEP1.SGM 06DEP1

Agencies

[Federal Register Volume 76, Number 234 (Tuesday, December 6, 2011)]
[Proposed Rules]
[Pages 76068-76070]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2011-31254]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2011-1285; Directorate Identifier 2010-SW-073-AD]
RIN 2120-AA64


Airworthiness Directives; Eurocopter Deutschland GmbH Helicopters

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for 
Eurocopter Deutschland GmbH Model BO-105A, BO-105C, BO-105LS A-1, BO-
105LS A-3, and BO-105S helicopters. This proposed AD would require 
inspecting certain main rotor blades for debonding of the erosion 
protective shell. If the erosion protective shell is debonded, you 
would be required to replace the main rotor blade with an airworthy 
main rotor blade. This proposed AD is prompted by the results of an 
inspection on a BO-105 helicopter where debonding was discovered on a 
main rotor blade erosion protective shell, and it was determined that 
the debonding was due to incorrect installation of the erosion 
protective shell. Subsequently, an incident occurred where a BO-105 
helicopter lost its main rotor blade erosion protective shell during 
flight. The actions specified by this proposed AD are intended to 
detect debonding of the main rotor blade erosion protective shell which 
could lead to an unbalanced main rotor, high vibrations, damage to the 
tail boom or tail rotor, and loss of control of the helicopter.

DATES: Comments must be received on or before February 6, 2012.

ADDRESSES: Use one of the following addresses to submit comments on 
this proposed AD:
     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: (202) 493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue SE., Washington, DC 20590, between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays.

[[Page 76069]]

    You may get the service information identified in this proposed AD 
from American Eurocopter Corporation, 2701 N. Forum Drive, Grand 
Prairie, TX 75052, telephone (972) 641-0000 or (800) 232-0323, fax 
(972) 641-3775, or at https://www.eurocopter.com/techpub.

FOR FURTHER INFORMATION CONTACT: Jim Grigg, Manager, FAA, Rotorcraft 
Directorate, Safety Management Group, 2601 Meacham Blvd., Fort Worth, 
TX 76137, telephone (817) 222-5126, fax (817) 222-5961.

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to send any written relevant data, views, or 
arguments about this proposed AD. Send your comments to an address 
listed under the caption ADDRESSES. Include the Docket No. ``FAA-2011-
1285, Directorate Identifier 2010-SW-073-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of this proposed AD. We 
will consider all comments received by the closing date and may amend 
this proposed AD because of those comments.
    We will post all comments we receive, without change, to https://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact 
with FAA personnel concerning this proposed rulemaking. Using the 
search function of the docket web site, you can find and read the 
comments to any of our dockets, including the name of the individual 
who sent or signed the comment. You may review the DOT's complete 
Privacy Act Statement in the Federal Register published on April 11, 
2000 (65 FR 19477-78).

Examining the Docket

    You may examine the docket that contains the proposed AD, any 
comments, and other information in person at the Docket Operations 
office between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The Docket Operations office (telephone (800) 647-5527) is 
located in Room W12-140 on the ground floor of the West Building at the 
street address stated in the ADDRESSES section. Comments will be 
available in the AD docket shortly after receipt.

Discussion

    The European Aviation Safety Agency (EASA), which is the Technical 
Agent for the Member States of the European Community, has issued 
Emergency AD No. 2010-0216-E, dated October 21, 2010 (corrected October 
29, 2010), to correct an unsafe condition for Eurocopter Deutschland 
Model BO-105A, BO-105C, BO-105D, BO-105LS A-1, BO-105LS A-3, and BO-
105S helicopters, all variants (except CB-5 and DBS-5, which are 
military models.) EASA advises that during an inspection on a BO-105 
helicopter, debonding was found on the erosion protective shell of a 
main rotor blade, and it was determined that the debonding was caused 
by incorrect installation of the erosion protective shell. In addition, 
EASA states that an incident occurred where a second BO-105 helicopter 
lost its erosion protective shell during flight. EASA advises that this 
condition, if not detected, could result in loss of the main rotor 
blade erosion protective shell during flight, leading to an unbalanced 
main rotor and high vibrations, which could result in damage to the 
tail boom or tail rotor, loss of tail rotor control, and loss of 
control of the helicopter.

Related Service Information

    Eurocopter Deutschland has issued Emergency Alert Service Bulletin 
No. BO105-10-124, dated July 14, 2010, for the Model BO105 helicopter, 
with a main rotor blade, part number (P/N) 105-15103, 105-15141, 105-
15141V001, 105-15143, 105-15150, 105-15150V001, 105-15152, 105-81013, 
105-87214, 1120-15101, or 1120-15103, where the main rotor blade 
erosion protective shell was replaced between September 2006 and March 
2010. Eurocopter Deutschland also issued Emergency Alert Service 
Bulletin BO105LS-10-12 for the Model BO105LS A-3 helicopter, dated July 
14, 2010, with a main rotor blade, part P/N 105-15141, where the main 
rotor blade erosion protective shell was replaced between September 
2006 and March 2010. Both Emergency Alert Service Bulletins specified a 
one-time inspection of the main rotor blades within the next 50 flight 
hours to determine if debonding of the main rotor blade erosion 
protective shell has occurred. Both Service Bulletins exclude 
helicopters from this inspection if each main rotor blade was inspected 
at the last 600 flight hour inspection and no debonding was detected 
during the inspection.
    In response to the incident where the helicopter lost its main 
rotor blade erosion protective shell during flight, Eurocopter 
Deutschland has issued Emergency Alert Service Bulletin No. BO105-10-
124, Revision 1, dated October 18, 2010, and Emergency Alert Service 
Bulletin BO105LS-10-12, Revision 1, dated October 20, 2010. These 
Service Bulletins specify the same inspection requirements as the 
original Service Bulletins, but revise the inspection compliance time 
from 50 flight hours to 10 flight hours. EASA classified these Service 
Bulletins as mandatory, and issued EASA Emergency AD No. 2010-0216-E, 
dated October 21, 2010 (corrected October 29, 2010) to ensure the 
continued airworthiness of these helicopters.

FAA's Evaluation and Unsafe Condition Determination

    These products have been approved by the aviation authority of 
Germany and are approved for operation in the United States. Pursuant 
to our bilateral agreement with Germany, EASA, their technical 
representative, has notified us of the unsafe condition described in 
their AD. We are proposing this AD because we evaluated all information 
provided by EASA and determined the unsafe condition exists and is 
likely to exist or develop on other products of these same type 
designs. This proposed AD would require a one-time inspection of each 
main rotor blade for debonding of the main rotor blade erosion 
protective shell within 50 hours time-in-service (TIS), for helicopters 
with a main rotor blade, P/N 105-15103, 105-15141, 105-15141V001, 105-
15143, 105-15150, 105-15150V001, 105-15152, 105-81013, 105-87214, 1120-
15101, or 1120-15103, where the main rotor blade erosion protective 
shell was replaced between September 2006 and March 2010. If debonding 
is detected during the inspection, before further flight, you would be 
required to replace the main rotor blade with an airworthy main rotor 
blade.

Differences Between This Proposed AD and the EASA AD

    The differences between this proposed AD and the EASA AD are:
     This proposed AD uses the term ``hours time-in-service'' 
to describe compliance times, and the EASA AD uses ``flight hours.''
     The EASA AD allows compliance within ``10 flight hours, or 
4 flight cycles, or 4 weeks, whichever occurs first,'' and this 
proposed AD would require compliance within 50 hours TIS.
     The EASA AD allows you to replace the main rotor blade 
erosion protective shell if debonding is detected, and this proposed AD 
would require you to replace the main rotor blade with an airworthy 
main rotor blade if debonding is detected.
     The EASA AD is applicable to the Model BO-105D helicopter, 
and this proposed AD does not include this model because it does not 
have a type-certificate in the U.S.

[[Page 76070]]

Costs of Compliance

    We estimate that this proposed AD would affect 97 helicopters of 
U.S. registry. We estimate that it would take about 1.0 work-hour per 
helicopter to do the inspection, at an average labor rate of $85 per 
work hour. Based on these figures, we estimate the cost of the proposed 
AD on U.S. operators to be $8,245, or $85 per product. If debonding is 
found, we estimate that it would take about 2 work-hours to replace the 
main rotor blade, and required parts would cost $114,182, for a cost of 
$114,352. We have no way of determining how many operators would incur 
these costs.

Regulatory Findings

    We have determined that this proposed AD would not have federalism 
implications under Executive Order 13132. Additionally, this proposed 
AD would not have a substantial direct effect on the States, on the 
relationship between the national Government and the States, or on the 
distribution of power and responsibilities among the various levels of 
government.
    For the reasons discussed above, I certify that the proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979);
    3. Will not affect intrastate aviation in Alaska to the extent that 
a regulatory distinction is required; and
    4. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared an economic evaluation of the estimated costs to comply 
with this proposed AD. See the AD docket to examine the economic 
evaluation.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, Section 106, describes the 
authority of the FAA Administrator. Subtitle VII, Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
subtitle VII, part A, subpart III, section 44701, ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
Reference, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

    1. The authority citation for Part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

    2. Section 39.13 is amended by adding a new airworthiness directive 
(AD) to read as follows:

Eurocopter Deutschland GMBH: Docket No. FAA-2011-1285; Directorate 
Identifier 2010-SW-073-AD.

    Applicability: Model BO-105A, BO-105C, BO-105LS A-1, BO-105LS A-
3, and BO-105S helicopters, all serial numbers, with a main rotor 
blade, part number (P/N) 105-15103, 105-15141, 105-15141V001, 105-
15143, 105-15150, 105-15150V001, 105-15152, 105-81013, 105-87214, 
1120-15101, or 1120-15103; where the main rotor blade erosion 
protective shell was replaced between September 2006 and March 2010; 
certificated in any category.
    Compliance: Required within 50 hours time-in-service (TIS) after 
the effective date of this AD, unless accomplished previously.
    To detect debonding of the main rotor blade erosion protective 
shell, which could lead to an unbalanced main rotor, high vibration, 
damage to the tail boom or tail rotor, and loss of control of the 
helicopter, accomplish the following:
    (a) Inspect the main rotor blade for debonding of the erosion 
protective shell. If debonding is detected during the inspection, 
before further flight, replace the main rotor blade with an 
airworthy main rotor blade.

    Note 1: Eurocopter Deutschland GmbH Emergency Alert Service 
Bulletin No. BO105-10-124, Revision 1, dated October 18, 2010, and 
No. BO105LS-10-12, Revision 1, dated October 20, 2010, which are not 
incorporated by reference, contain additional information about the 
subject of this AD.

    (b) To request a different method of compliance or a different 
compliance time for this AD, follow the procedures in 14 CFR 39.19. 
Contact the Manager, Regulations and Policy Group, FAA, ATTN: Jim 
Grigg, Manager, 2601 Meacham Blvd., Fort Worth, Texas 76137; 
telephone: (817) 222-5122; fax: (817) 222-5126, for information 
about previously approved alternative methods of compliance.
    (c) The Joint Aircraft System/Component Code is 6210: Main Rotor 
Blades.

    Note 2: The subject of this AD is addressed in European Aviation 
Safety Agency AD 2010-0216-E, dated October 21, 2010 (corrected 
October 29, 2010).


    Issued in Fort Worth, Texas, on November 29, 2011.
Lance T. Gant,
Acting Manager, Rotorcraft Directorate, Aircraft Certification Service.
[FR Doc. 2011-31254 Filed 12-5-11; 8:45 am]
BILLING CODE 4910-13-P
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.