Special Conditions: Diamond Aircraft Industries, Model DA-40NG; Electronic Engine Control (EEC) System, 72087-72091 [2011-28616]

Download as PDF Federal Register / Vol. 76, No. 225 / Tuesday, November 22, 2011 / Rules and Regulations § 110.7 Information collection requirements: OMB approval. 201, Pub. L. 93–438, 88 Stat. 1242, as amended (42 U.S.C. 5841); sec. 205a, Pub. L. 101–576, 104 Stat. 2842, as amended (31 U.S.C. 901, 902); sec. 1704, 112 Stat. 2750 (44 U.S.C. 3504 note); sec. 623, Pub. L. 109–58, 119 Stat. 783 (42 U.S.C. 2201(w)); sec. 651(e), Pub. L. 109–58, 119 Stat. 806–810 (42 U.S.C. 2014, 2021, 2021b, 2111). * § 170.31 553. Sections 110.2 and 110.42(a)(9) also issued under sec. 903, Pub. L. 102–496 (42 U.S.C. 2151 et seq.). 31. Section 110.7, paragraph (b), is revised to read as follows: ■ * * * * (b) The approved information requirements contained in this part appear in §§ 110.7a, 110.27, 110.32, 110.50, 110.52, 110.53, and 110.54. * * * * * [Amended] 33. In § 170.31, remove footnote 6 and the corresponding reference to footnote 6 in 15.M, 15.N, 15.O, 15.P, and 15.Q. ■ PART 170—FEES FOR FACILITIES, MATERIALS IMPORT AND EXPORT LICENSES AND OTHER REGULATORY SERVICES UNDER THE ATOMIC ENERGY ACT OF 1954, AS AMENDED 32. The authority citation for part 170 continues to read as follows: ■ Authority: Sec. 9701, Pub. L. 97–258, 96 Stat. 1051 (31 U.S.C. 9701); sec. 301, Pub. L. 92–314, 86 Stat. 227 (42 U.S.C. 2201(w)); sec. PART 171—ANNUAL FEES FOR REACTOR LICENSES AND FUEL CYCLE LICENSES AND MATERIAL LICENSES, INCLUDING HOLDERS OF CERTIFICATES OF COMPLIANCE, REGISTRATIONS, AND QUALITY ASSURANCE PROGRAM APPROVALS AND GOVERNMENT AGENCIES LICENSED BY NRC 34. The authority citation for part 171 continues to read as follows: ■ 72087 Authority: Sec. 7601, Pub. L. 99–272, 100 Stat. 146, as amended by sec. 5601, Pub. L. 100–203, 101 Stat. 1330 as amended by sec. 3201, Pub. L. 101–239, 103 Stat. 2132, as amended by sec. 6101, Pub. L. 101–508, 104 Stat. 1388, as amended by sec. 2903a, Pub. L. 102–486, 106 Stat. 3125 (42 U.S.C. 2213, 2214), and as amended by Title IV, Pub. L. 109–103, 119 Stat. 2283 (42 U.S.C. 2214); sec. 301, Pub. L. 92–314, 86 Stat. 227 (42 U.S.C. 2201w); sec. 201, Pub. L. 93–438, 88 Stat. 1242, as amended (42 U.S.C. 5841); sec. 1704, 112 Stat. 2750 (44 U.S.C. 3504 note); sec. 651(e), Pub. L. 109–58, 119 Stat. 806–810 (42 U.S.C. 2014, 2021, 2021b, 2111). 35. In § 171.16, paragraph (c), the table is revised to read as follows: ■ § 171.16 Annual fees: Materials licensees, holders of certificates of compliance, holders of sealed source and device registrations, holders of quality assurance program approvals, and government agencies licensed by the NRC. * * * (c) * * * * * Maximum annual fee per licensed category Small Businesses Not Engaged in Manufacturing (Average gross receipts over last 3 completed fiscal years): $450,000 to $6.5 million ........................................................................................................................................................... Less than $450,000 .................................................................................................................................................................. Small Not-For-Profit Organizations (Annual Gross Receipts): $450,000 to $6.5 million ........................................................................................................................................................... Less than $450,000 .................................................................................................................................................................. Manufacturing entities that have an average of 500 employees or fewer: 35 to 500 employees ................................................................................................................................................................ Fewer than 35 employees ........................................................................................................................................................ Small Governmental Jurisdictions (Including publicly supported educational institutions) (Population): 20,000 to 50,000 ...................................................................................................................................................................... Fewer than 20,000 ................................................................................................................................................................... Educational Institutions that are not State or Publicly Supported, and have 500 Employees or Fewer: 35 to 500 employees ................................................................................................................................................................ Fewer than 35 employees ........................................................................................................................................................ * * * * * DEPARTMENT OF TRANSPORTATION Dated at Rockville, Maryland, this 10th day of November 2011. For the Nuclear Regulatory Commission. Cindy Bladey, Chief, Rules, Announcements, and Directives Branch, Division of Administrative Services, Office of Administration. [FR Doc. 2011–29669 Filed 11–21–11; 8:45 am] BILLING CODE 7590–01–P Federal Aviation Administration 14 CFR Part 23 [Docket No. CE313; Special Conditions No. 23–253–SC] Special Conditions: Diamond Aircraft Industries, Model DA–40NG; Electronic Engine Control (EEC) System Federal Aviation Administration (FAA), DOT. ACTION: Final special conditions. erowe on DSK2VPTVN1PROD with RULES AGENCY: These special conditions are issued for the Diamond Aircraft Industries, Model DA–40NG airplane. This airplane will have a novel or unusual design feature(s) associated with an electronic engine control (EEC) also known as a Full authority Digital SUMMARY: VerDate Mar<15>2010 13:43 Nov 21, 2011 Jkt 226001 PO 00000 Frm 00007 Fmt 4700 Sfmt 4700 $2,300 500 2,300 500 2,300 500 2,300 500 2,300 500 Engine Control (FADEC). The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards. DATES: Effective Date: October 28, 2011. FOR FURTHER INFORMATION CONTACT: Peter L. Rouse, Federal Aviation Administration, Aircraft Certification Service, Small Airplane Directorate, ACE–111, 901 Locust, Kansas City, Missouri, (816) 329–4135, fax (816) 329–4090. SUPPLEMENTARY INFORMATION: Background On May 11, 2010, Diamond Aircraft Industry GmbH applied for an E:\FR\FM\22NOR1.SGM 22NOR1 72088 Federal Register / Vol. 76, No. 225 / Tuesday, November 22, 2011 / Rules and Regulations erowe on DSK2VPTVN1PROD with RULES amendment to Type Certificate No. A47CE to include the new model DA– 40NG with the Austro Engine GmbH model E4 Aircraft Diesel Engine (ADE). The model DA–40NG, which is a derivative of the model DA–40 currently approved under Type Certificate No. A47CE, is a fully composite, four place, single-engine airplane with a cantilever low wing, T-tail airplane with the Austro Engine GmbH model E4 diesel engine and an increased maximum takeoff gross weight from 1150 kilograms (kg) to 1280 kg (2535 pounds (lbs) to 2816 lbs). DAI will use an EEC instead of a traditional mechanical control system on the model DA–40NG airplane. The EEC is certified as part of the engine design certification, and the certification requirements for engine control systems are driven by 14 CFR part 33 certification requirements. The guidance for the part 33 EEC certification requirement is contained in two advisory circulars: Advisory Circular (AC) 33.28–1 and AC 33.28–2. The EEC certification, as part of the engine, addresses those aspects of the engine specifically addressed by part 33 and is not intended to address 14 CFR part 23 installation requirements. However, the VerDate Mar<15>2010 13:43 Nov 21, 2011 Jkt 226001 guidance does highlight some of the aspects of installation that the engine applicant should consider during engine certification. The installation of an engine with an EEC system requires evaluation of environmental effects and possible effects on or by other airplane systems, including the part 23 installation aspects of the EEC functions. For example, the indirect effects of lightning, radio interference with other airplane electronic systems, and shared engine and airplane data and power sources. The regulatory requirements in part 23 for evaluating the installation of complex electronic systems are contained in § 23.1309. However, when § 23.1309 was developed, the requirements of the rule were specifically excluded from applying to powerplant systems provided as part of the engine (reference § 23.1309(f)(1)). Although the parts of the system that are not certificated with the engine could be evaluated using the criteria of § 23.1309, the analysis would not be useful and not be complete because it would not include the effects of the aircraft supplied power and data failures on the engine control system, and the resulting effects on engine power/thrust. The PO 00000 Frm 00008 Fmt 4700 Sfmt 4700 integral nature of EEC installations require review of EEC functionality at the airplane level, as behavior acceptable for part 33 certification may not be acceptable for part 23 certification. For over a decade, the Small Airplane Directorate has applied a special condition that required all EEC installations to comply with the requirements of § 23.1309(a) through (e). The rationale for applying § 23.1309 was that it was an existing rule that contained the best available requirements to apply to the installation of a complex electronic system; in this case, an EEC with aircraft interfaces. Additionally, special conditions for High Intensity Radiated Fields (HIRF) were also applied prior to the codification of § 23.1308. There are several difficulties for propulsion systems directly complying with the requirements of § 23.1309. There are conflicts between the guidance material for § 23.1309 and propulsion system capabilities and failure susceptibilities. The following figure is an excerpt from AC 23.1309– 1D. BILLING CODE 4910–13–P E:\FR\FM\22NOR1.SGM 22NOR1 Federal Register / Vol. 76, No. 225 / Tuesday, November 22, 2011 / Rules and Regulations erowe on DSK2VPTVN1PROD with RULES There is a conflict between the EEC system loss-of-thrust-control (LOTC), or loss-of-power-control (LOPC), probability per hour requirements given in part 33 guidance material and the failure rate requirements associated with the hazard created by a total loss Engine type Average LOTC/LOPC Events per million hours Turbine Engine .................................................. Reciprocating Engine ......................................... 10 (1 × 10–05 per hour) ................................... 45 (4.5 × 10–05 per hour) ................................ of power/thrust as given in part 23 AC 23.1309–1D guidance. The part 33 requirements for engine control LOTC/ LOPC probabilities are shown below: Maximum LOTC/LOPC Events per million hours 100 (1 × 10–04 per hour). 450 (4.5 × 10–04 per hour). Note: See AC 33.28–1, AC 33.28–2 and ANE–1993–33.28TLD–R1 for further guidance. VerDate Mar<15>2010 13:43 Nov 21, 2011 Jkt 226001 PO 00000 Frm 00009 Fmt 4700 Sfmt 4700 E:\FR\FM\22NOR1.SGM 22NOR1 ER22NO11.003</GPH> BILLING CODE 4910–13–C 72089 erowe on DSK2VPTVN1PROD with RULES 72090 Federal Register / Vol. 76, No. 225 / Tuesday, November 22, 2011 / Rules and Regulations The classification of the failure condition for LOTC/LOPC event on a single engine airplane ranges from Hazardous to Catastrophic. The classification of the failure condition for a single engine LOTC/LOPC event on a multi-engine airplane ranges from Major to Catastrophic. The classification of the failure condition for a multi-engine LOTC/LOPC event on a multi-engine airplane is Catastrophic. From the AC 23.1309–1D failure probability values, it is obvious that a single engine airplane EEC system will not be able to meet the failure probabilities as shown in the guidance material for § 23.1309. As a result, applicants have elected to declare a reduced hazard severity for a failure of the EEC system. This is not the intent of § 23.1309. The greater hazard severity should be associated with lower probabilities of failure, and higher probabilities of failure should not establish the lower hazard severities. There is also a conflict between the classification of the failure condition for a failure of an EEC system and the required test levels for the effects of lightning and high intensity radiated frequency (HIRF). Testing to a level lower than required for a catastrophic failure results in a lower level of safety than the mechanical system it replaces. This is contrary to the intent of certification requirements. The advent of EEC also created/ established the ability to dispatch with certain allowable loss of functionality and/or redundancy. This is known as Time-Limited Dispatch (TLD). The TLD allowable configurations must meet the specific risk LOTC/LOPC failure probabilities. FAA policy statement, ANE–1993–33.28TLD–R1, defines the full up and TLD allowable failure probabilities for turbine engines. The ability to use TLD is a risk management endeavor that uses a limited time period between inspection/maintenance intervals to mitigate the hazard. As such, the FAA has issued specific guidance for part 23 airplanes in addition to policy statement, ANE– 1993–33.28TLD–R1, in order to adequately capture the necessary time limits between maintenance intervals. A means of compliance issue paper giving specific guidance can be generated, if desired, for the applicant. The advent of EEC also led to incorporation of functions that, while not required by the CFRs, also introduce potentially catastrophic failure(s) and malfunction(s). Consequently, incorporation of these additional functions must be shown to retain part 23 levels of safety. These additional functions have included thrust management, portions of engine VerDate Mar<15>2010 13:43 Nov 21, 2011 Jkt 226001 indication otherwise provided as part of the engine installation, engine speed synchronization, ignition control, autofeather, etc. The certification of an airplane to the standards of 14 CFR part 25 does not require the application of § 25.1309 via special condition to the EEC installation. In part 25, § 25.1309 is applicable to the powerplant installations in general and as a whole. The part 25 consequences differ from part 23 due to the required multi-engine configuration of part 25 airplanes. Additional applicable part 25, Subpart E requirements are those contained within § 25.901(b)(2) and (c). There is language similar to part 25, § 25.901(c) contained in part 23, § 23.1141(e).The requirements contained within § 23.1141(e) were originally intended for the mechanical control interfaces on turbine engines. The rule was first promulgated at Amendment 23–7, effective on September 14, 1969. The preamble justifying the rule change states: ‘‘This proposal would, in effect require that the need for system redundancy, alternate devices, and duplication of functions be determined in the design of turbine powerplant control systems.’’ The overall intent of the above cited rules is to provide a robust and fault tolerant engine control installation that ensures that no single failure or malfunction or probable combination of failures will jeopardize the safe operation of the airplane. Given the unique requirements of an EEC installation, and the lack of specific regulatory requirements, a special condition will be applied to all EEC installations in part 23 airplanes. This special condition is not applicable to the part 33 engine certification requirements, and it specifically excludes any part 33 references. Compliance with this special condition may necessitate changes to the EEC, and may require additional part 33 compliance showings. In like manner, changes to the EEC at the part 33 level may require additional compliance showings to this special condition. The overall intent of this special condition is to leverage off of the part 33 compliance as much as possible and address the airplane level effects of an EEC installation. The EEC system includes all of the subsystems on the aircraft that interface with the EEC and provide aircraft data and electrical power. This special condition is applicable to and includes all functions of the EEC system that have an effect at the airplane level. An example of this is control of the turbine PO 00000 Frm 00010 Fmt 4700 Sfmt 4700 engine compressor variable geometry (VG): the VG function in itself is not an airplane function, but changes to the VG scheduling will require re-substantiating compliance to part 23 requirements, such as § 23.939. The components that should be considered part of the EEC system are defined in Society of Automotive Engineers (SAE) document, Aerospace Recommended Practice (ARP) 5107B, Guidelines for Time-Limited-Dispatch (TLD) Analysis for Electronic Engine Control Systems, section 6.4. This guidance is intended for turbine engine installations; however, the intent is applicable to piston engine installations. A means of compliance issue paper giving specific guidance can be generated, if desired, for the applicant. Part 33 certification data, if applicable, may be used to show compliance with the requirements of part 23 installation requirements; however, compliance with the part 33 requirements does not constitute compliance with the requirements of part 23, nor automatically imply that the engine is installable on a part 23 airplane. The part 23 applicant is required to show compliance in accordance with part 21. If part 33 data is to be used, then the part 23 applicant must be able to provide this data for their showing of compliance to the part 23 requirements. Type Certification Basis Under the provisions of § 21.101, DAI must show that the model DA–40NG meets the applicable provisions of the regulations incorporated by reference in Type Certificate No. A47CE or the applicable regulations in effect on the date of application for the change to the model DA–40. The regulations incorporated by reference in the type certificate are commonly referred to as the ‘‘original type certification basis.’’ If the Administrator finds that the applicable airworthiness regulations (i.e., 14 CFR part 23) do not contain adequate or appropriate safety standards for the model DA–40NG because of a novel or unusual design feature, special conditions are prescribed under the provisions of § 21.16. In addition to the applicable airworthiness regulations and special conditions, the model DA–40NG must comply with the fuel vent and exhaust emission requirements of 14 CFR part 34 and the noise certification requirements of 14 CFR part 36. The FAA issues special conditions, as appropriate, as defined in § 11.19, under § 11.38, and they become part of the type certification basis under § 21.101(b)(2). E:\FR\FM\22NOR1.SGM 22NOR1 Federal Register / Vol. 76, No. 225 / Tuesday, November 22, 2011 / Rules and Regulations Special conditions are initially applicable to the model for which they are issued. Should the type certificate for that model be amended later to include any other model that incorporates the same novel or unusual design feature, or should any other model already included on the same type certificate be modified to incorporate the same novel or unusual design feature, the special conditions would also apply to the other model under the provisions of § 21.101(a)(1). Novel or Unusual Design Features The model DA–40NG will incorporate the following novel or unusual design features: Electronic engine control system. Discussion As discussed above, these special conditions are applicable to the model DA–40NG. Should DAI apply at a later date for a change to the type certificate to include another model incorporating the same novel or unusual design feature, the special conditions would apply to that model. Discussion of Comments Notice of proposed special conditions No. 23–10–03–SC for the Diamond Aircraft Industries, model DA–40NG, airplane was published on September 7, 2011 (76FR 55293). No comments were received, and the special conditions are adopted as proposed. Applicability As discussed above, these special conditions are applicable to the model DA–40NG. Should DAI apply at a later date for a change to the type certificate to include another model incorporating the same novel or unusual design feature, the special conditions would apply to that model. Under standard practice, the effective date of final special conditions would be 30 days after the date of publication in the Federal Register; however, as the certification date for the Diamond Aircraft Industries (DAI), model DA– 40NG airplane is imminent, the FAA finds that good cause exists to make these special conditions effective upon issuance. erowe on DSK2VPTVN1PROD with RULES Conclusion This action affects only certain novel or unusual design features on one model of airplane. It is not a rule of general applicability, and it affects only the applicant who applied to the FAA for approval of these features on the airplane. VerDate Mar<15>2010 13:43 Nov 21, 2011 Jkt 226001 List of Subjects in 14 CFR Part 23 Aircraft, Aviation safety, Signs and symbols. Citation The authority citation for these special conditions is as follows: Authority: 49 U.S.C. 106(g), 40113 and 44701; 14 CFR 21.16 and 21.17; and 14 CFR 11.38 and 11.19. Accordingly, pursuant to the authority delegated to me by the Administrator, the following special conditions are issued as part of the type certification basis for the Diamond Aircraft Industry GmbH model DA– 40NG with the installation of the Austro Engine GmbH model E4 aircraft diesel engine. 1. Electronic Engine Control Note: The term ‘‘probable’’ in the context of ‘‘probable combination of failures’’ does not have the same meaning as in AC Fmt 4700 Sfmt 4700 Issued in Kansas City, Missouri on October 28, 2011. John Colomy, Acting Manager, Small Airplane Directorate, Aircraft Certification Service. [FR Doc. 2011–28616 Filed 11–21–11; 8:45 am] DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2011–1037; Directorate Identifier 2011–NE–30–AD; Amendment 39– 16872; AD 2011–24–08] RIN 2120–AA64 a. For electronic engine control system installations, it must be established that no single failure or malfunction or probable combinations of failures of Electronic Engine Control (EEC) system components will have an effect on the system, as installed in the airplane, that causes the loss-of-thrustcontrol (LOTC), or loss-of-power-control (LOPC) probability of the system to exceed those allowed in part 33 certification. b. Electronic engine control system installations must be evaluated for environmental and atmospheric conditions, including lightning. The EEC system lightning and High-Intensity Radiated Fields (HIRF) effects that result in LOTC/LOPC should be considered catastrophic. c. The components of the installation must be constructed, arranged, and installed so as to ensure their continued safe operation between normal inspections or overhauls. d. Functions incorporated into any electronic engine control that make it part of any equipment, systems or installation whose functions are beyond that of basic engine control, and which may also introduce system failures and malfunctions, are not exempt from § 23.1309 and must be shown to meet part 23 levels of safety as derived from § 23.1309. Part 33 certification data, if applicable, may be used to show compliance with any part 23 requirements. If part 33 data is to be used to substantiate compliance with part 23 requirements, then the part 23 applicant must be able to provide this data for their showing of compliance. Frm 00011 23.1309–1D. The term ‘‘probable’’ in ‘‘probable combination of failures’’ means ‘‘foreseeable,’’ or (in AC 23.1309–1D terms), ‘‘not extremely improbable.’’ BILLING CODE 4910–13–P The Special Conditions PO 00000 72091 Airworthiness Directives; Turbomeca S.A. Makila 1A2 Turboshaft Engines Federal Aviation Administration (FAA), DOT. ACTION: Final rule; request for comments. AGENCY: We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: SUMMARY: A helicopter experienced an inadvertent activation of the 65% N1 (gas generator speed) back up control mode. The subsequent technical investigations carried by Turbomeca revealed that an N2 (power turbine speed) sensor harness wire crimping discrepancy was at the origin of this event. Further quality investigations performed with the supplier led to the conclusion that N2 sensor Part Number (P/N) 0 301 52 001 0 whose Serial Numbers (S/N) are between S/N 242 and S/N 339 inclusive are potentially concerned by the same manufacturing discrepancy. This condition, if not corrected, could lead to the inadvertent activation of the 65% N1 back up mode and consequently to significant power loss on one or more or both engines installed on the same helicopter, potentially resulting in an emergency landing of the helicopter. We are issuing this AD to prevent inadvertent activation of the backup control mode, which could result in engine power loss and emergency landing of the helicopter. DATES: This AD becomes effective December 7, 2011. E:\FR\FM\22NOR1.SGM 22NOR1

Agencies

[Federal Register Volume 76, Number 225 (Tuesday, November 22, 2011)]
[Rules and Regulations]
[Pages 72087-72091]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2011-28616]


=======================================================================
-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 23

[Docket No. CE313; Special Conditions No. 23-253-SC]


Special Conditions: Diamond Aircraft Industries, Model DA-40NG; 
Electronic Engine Control (EEC) System

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final special conditions.

-----------------------------------------------------------------------

SUMMARY: These special conditions are issued for the Diamond Aircraft 
Industries, Model DA-40NG airplane. This airplane will have a novel or 
unusual design feature(s) associated with an electronic engine control 
(EEC) also known as a Full authority Digital Engine Control (FADEC). 
The applicable airworthiness regulations do not contain adequate or 
appropriate safety standards for this design feature. These special 
conditions contain the additional safety standards that the 
Administrator considers necessary to establish a level of safety 
equivalent to that established by the existing airworthiness standards.

DATES: Effective Date: October 28, 2011.

FOR FURTHER INFORMATION CONTACT: Peter L. Rouse, Federal Aviation 
Administration, Aircraft Certification Service, Small Airplane 
Directorate, ACE-111, 901 Locust, Kansas City, Missouri, (816) 329-
4135, fax (816) 329-4090.

SUPPLEMENTARY INFORMATION:

Background

    On May 11, 2010, Diamond Aircraft Industry GmbH applied for an

[[Page 72088]]

amendment to Type Certificate No. A47CE to include the new model DA-
40NG with the Austro Engine GmbH model E4 Aircraft Diesel Engine (ADE). 
The model DA-40NG, which is a derivative of the model DA-40 currently 
approved under Type Certificate No. A47CE, is a fully composite, four 
place, single-engine airplane with a cantilever low wing, T-tail 
airplane with the Austro Engine GmbH model E4 diesel engine and an 
increased maximum takeoff gross weight from 1150 kilograms (kg) to 1280 
kg (2535 pounds (lbs) to 2816 lbs).
    DAI will use an EEC instead of a traditional mechanical control 
system on the model DA-40NG airplane. The EEC is certified as part of 
the engine design certification, and the certification requirements for 
engine control systems are driven by 14 CFR part 33 certification 
requirements. The guidance for the part 33 EEC certification 
requirement is contained in two advisory circulars: Advisory Circular 
(AC) 33.28-1 and AC 33.28-2. The EEC certification, as part of the 
engine, addresses those aspects of the engine specifically addressed by 
part 33 and is not intended to address 14 CFR part 23 installation 
requirements. However, the guidance does highlight some of the aspects 
of installation that the engine applicant should consider during engine 
certification. The installation of an engine with an EEC system 
requires evaluation of environmental effects and possible effects on or 
by other airplane systems, including the part 23 installation aspects 
of the EEC functions. For example, the indirect effects of lightning, 
radio interference with other airplane electronic systems, and shared 
engine and airplane data and power sources.
    The regulatory requirements in part 23 for evaluating the 
installation of complex electronic systems are contained in Sec.  
23.1309. However, when Sec.  23.1309 was developed, the requirements of 
the rule were specifically excluded from applying to powerplant systems 
provided as part of the engine (reference Sec.  23.1309(f)(1)). 
Although the parts of the system that are not certificated with the 
engine could be evaluated using the criteria of Sec.  23.1309, the 
analysis would not be useful and not be complete because it would not 
include the effects of the aircraft supplied power and data failures on 
the engine control system, and the resulting effects on engine power/
thrust. The integral nature of EEC installations require review of EEC 
functionality at the airplane level, as behavior acceptable for part 33 
certification may not be acceptable for part 23 certification.
    For over a decade, the Small Airplane Directorate has applied a 
special condition that required all EEC installations to comply with 
the requirements of Sec.  23.1309(a) through (e). The rationale for 
applying Sec.  23.1309 was that it was an existing rule that contained 
the best available requirements to apply to the installation of a 
complex electronic system; in this case, an EEC with aircraft 
interfaces. Additionally, special conditions for High Intensity 
Radiated Fields (HIRF) were also applied prior to the codification of 
Sec.  23.1308.
    There are several difficulties for propulsion systems directly 
complying with the requirements of Sec.  23.1309. There are conflicts 
between the guidance material for Sec.  23.1309 and propulsion system 
capabilities and failure susceptibilities. The following figure is an 
excerpt from AC 23.1309-1D.
BILLING CODE 4910-13-P

[[Page 72089]]

[GRAPHIC] [TIFF OMITTED] TR22NO11.003

BILLING CODE 4910-13-C
    There is a conflict between the EEC system loss-of-thrust-control 
(LOTC), or loss-of-power-control (LOPC), probability per hour 
requirements given in part 33 guidance material and the failure rate 
requirements associated with the hazard created by a total loss of 
power/thrust as given in part 23 AC 23.1309-1D guidance. The part 33 
requirements for engine control LOTC/LOPC probabilities are shown 
below:

------------------------------------------------------------------------
                                   Average LOTC/LOPC   Maximum LOTC/LOPC
           Engine type            Events per million  Events per million
                                         hours               hours
------------------------------------------------------------------------
Turbine Engine..................  10 (1 x 10-05 per   100 (1 x 10-04 per
                                   hour).              hour).
Reciprocating Engine............  45 (4.5 x 10-05     450 (4.5 x 10-04
                                   per hour).          per hour).
------------------------------------------------------------------------
Note: See AC 33.28-1, AC 33.28-2 and ANE-1993-33.28TLD-R1 for further
  guidance.


[[Page 72090]]

    The classification of the failure condition for LOTC/LOPC event on 
a single engine airplane ranges from Hazardous to Catastrophic. The 
classification of the failure condition for a single engine LOTC/LOPC 
event on a multi-engine airplane ranges from Major to Catastrophic. The 
classification of the failure condition for a multi-engine LOTC/LOPC 
event on a multi-engine airplane is Catastrophic. From the AC 23.1309-
1D failure probability values, it is obvious that a single engine 
airplane EEC system will not be able to meet the failure probabilities 
as shown in the guidance material for Sec.  23.1309. As a result, 
applicants have elected to declare a reduced hazard severity for a 
failure of the EEC system. This is not the intent of Sec.  23.1309. The 
greater hazard severity should be associated with lower probabilities 
of failure, and higher probabilities of failure should not establish 
the lower hazard severities. There is also a conflict between the 
classification of the failure condition for a failure of an EEC system 
and the required test levels for the effects of lightning and high 
intensity radiated frequency (HIRF). Testing to a level lower than 
required for a catastrophic failure results in a lower level of safety 
than the mechanical system it replaces. This is contrary to the intent 
of certification requirements.
    The advent of EEC also created/established the ability to dispatch 
with certain allowable loss of functionality and/or redundancy. This is 
known as Time-Limited Dispatch (TLD). The TLD allowable configurations 
must meet the specific risk LOTC/LOPC failure probabilities. FAA policy 
statement, ANE-1993-33.28TLD-R1, defines the full up and TLD allowable 
failure probabilities for turbine engines. The ability to use TLD is a 
risk management endeavor that uses a limited time period between 
inspection/maintenance intervals to mitigate the hazard. As such, the 
FAA has issued specific guidance for part 23 airplanes in addition to 
policy statement, ANE-1993-33.28TLD-R1, in order to adequately capture 
the necessary time limits between maintenance intervals. A means of 
compliance issue paper giving specific guidance can be generated, if 
desired, for the applicant.
    The advent of EEC also led to incorporation of functions that, 
while not required by the CFRs, also introduce potentially catastrophic 
failure(s) and malfunction(s). Consequently, incorporation of these 
additional functions must be shown to retain part 23 levels of safety. 
These additional functions have included thrust management, portions of 
engine indication otherwise provided as part of the engine 
installation, engine speed synchronization, ignition control, auto-
feather, etc.
    The certification of an airplane to the standards of 14 CFR part 25 
does not require the application of Sec.  25.1309 via special condition 
to the EEC installation. In part 25, Sec.  25.1309 is applicable to the 
powerplant installations in general and as a whole. The part 25 
consequences differ from part 23 due to the required multi-engine 
configuration of part 25 airplanes. Additional applicable part 25, 
Subpart E requirements are those contained within Sec.  25.901(b)(2) 
and (c).
    There is language similar to part 25, Sec.  25.901(c) contained in 
part 23, Sec.  23.1141(e).The requirements contained within Sec.  
23.1141(e) were originally intended for the mechanical control 
interfaces on turbine engines. The rule was first promulgated at 
Amendment 23-7, effective on September 14, 1969. The preamble 
justifying the rule change states:

    ``This proposal would, in effect require that the need for 
system redundancy, alternate devices, and duplication of functions 
be determined in the design of turbine powerplant control systems.''

    The overall intent of the above cited rules is to provide a robust 
and fault tolerant engine control installation that ensures that no 
single failure or malfunction or probable combination of failures will 
jeopardize the safe operation of the airplane.
    Given the unique requirements of an EEC installation, and the lack 
of specific regulatory requirements, a special condition will be 
applied to all EEC installations in part 23 airplanes. This special 
condition is not applicable to the part 33 engine certification 
requirements, and it specifically excludes any part 33 references. 
Compliance with this special condition may necessitate changes to the 
EEC, and may require additional part 33 compliance showings. In like 
manner, changes to the EEC at the part 33 level may require additional 
compliance showings to this special condition. The overall intent of 
this special condition is to leverage off of the part 33 compliance as 
much as possible and address the airplane level effects of an EEC 
installation.
    The EEC system includes all of the subsystems on the aircraft that 
interface with the EEC and provide aircraft data and electrical power. 
This special condition is applicable to and includes all functions of 
the EEC system that have an effect at the airplane level. An example of 
this is control of the turbine engine compressor variable geometry 
(VG): the VG function in itself is not an airplane function, but 
changes to the VG scheduling will require re-substantiating compliance 
to part 23 requirements, such as Sec.  23.939.
    The components that should be considered part of the EEC system are 
defined in Society of Automotive Engineers (SAE) document, Aerospace 
Recommended Practice (ARP) 5107B, Guidelines for Time-Limited-Dispatch 
(TLD) Analysis for Electronic Engine Control Systems, section 6.4. This 
guidance is intended for turbine engine installations; however, the 
intent is applicable to piston engine installations. A means of 
compliance issue paper giving specific guidance can be generated, if 
desired, for the applicant.
    Part 33 certification data, if applicable, may be used to show 
compliance with the requirements of part 23 installation requirements; 
however, compliance with the part 33 requirements does not constitute 
compliance with the requirements of part 23, nor automatically imply 
that the engine is installable on a part 23 airplane. The part 23 
applicant is required to show compliance in accordance with part 21. If 
part 33 data is to be used, then the part 23 applicant must be able to 
provide this data for their showing of compliance to the part 23 
requirements.

Type Certification Basis

    Under the provisions of Sec.  21.101, DAI must show that the model 
DA-40NG meets the applicable provisions of the regulations incorporated 
by reference in Type Certificate No. A47CE or the applicable 
regulations in effect on the date of application for the change to the 
model DA-40. The regulations incorporated by reference in the type 
certificate are commonly referred to as the ``original type 
certification basis.''
    If the Administrator finds that the applicable airworthiness 
regulations (i.e., 14 CFR part 23) do not contain adequate or 
appropriate safety standards for the model DA-40NG because of a novel 
or unusual design feature, special conditions are prescribed under the 
provisions of Sec.  21.16.
    In addition to the applicable airworthiness regulations and special 
conditions, the model DA-40NG must comply with the fuel vent and 
exhaust emission requirements of 14 CFR part 34 and the noise 
certification requirements of 14 CFR part 36.
    The FAA issues special conditions, as appropriate, as defined in 
Sec.  11.19, under Sec.  11.38, and they become part of the type 
certification basis under Sec.  21.101(b)(2).

[[Page 72091]]

    Special conditions are initially applicable to the model for which 
they are issued. Should the type certificate for that model be amended 
later to include any other model that incorporates the same novel or 
unusual design feature, or should any other model already included on 
the same type certificate be modified to incorporate the same novel or 
unusual design feature, the special conditions would also apply to the 
other model under the provisions of Sec.  21.101(a)(1).

Novel or Unusual Design Features

    The model DA-40NG will incorporate the following novel or unusual 
design features: Electronic engine control system.

Discussion

    As discussed above, these special conditions are applicable to the 
model DA-40NG. Should DAI apply at a later date for a change to the 
type certificate to include another model incorporating the same novel 
or unusual design feature, the special conditions would apply to that 
model.

Discussion of Comments

    Notice of proposed special conditions No. 23-10-03-SC for the 
Diamond Aircraft Industries, model DA-40NG, airplane was published on 
September 7, 2011 (76FR 55293). No comments were received, and the 
special conditions are adopted as proposed.

Applicability

    As discussed above, these special conditions are applicable to the 
model DA-40NG. Should DAI apply at a later date for a change to the 
type certificate to include another model incorporating the same novel 
or unusual design feature, the special conditions would apply to that 
model.
    Under standard practice, the effective date of final special 
conditions would be 30 days after the date of publication in the 
Federal Register; however, as the certification date for the Diamond 
Aircraft Industries (DAI), model DA-40NG airplane is imminent, the FAA 
finds that good cause exists to make these special conditions effective 
upon issuance.

Conclusion

    This action affects only certain novel or unusual design features 
on one model of airplane. It is not a rule of general applicability, 
and it affects only the applicant who applied to the FAA for approval 
of these features on the airplane.

List of Subjects in 14 CFR Part 23

    Aircraft, Aviation safety, Signs and symbols.

Citation

    The authority citation for these special conditions is as follows:

    Authority:  49 U.S.C. 106(g), 40113 and 44701; 14 CFR 21.16 and 
21.17; and 14 CFR 11.38 and 11.19.

The Special Conditions

    Accordingly, pursuant to the authority delegated to me by the 
Administrator, the following special conditions are issued as part of 
the type certification basis for the Diamond Aircraft Industry GmbH 
model DA-40NG with the installation of the Austro Engine GmbH model E4 
aircraft diesel engine.

1. Electronic Engine Control

    a. For electronic engine control system installations, it must be 
established that no single failure or malfunction or probable 
combinations of failures of Electronic Engine Control (EEC) system 
components will have an effect on the system, as installed in the 
airplane, that causes the loss-of-thrust-control (LOTC), or loss-of-
power-control (LOPC) probability of the system to exceed those allowed 
in part 33 certification.
    b. Electronic engine control system installations must be evaluated 
for environmental and atmospheric conditions, including lightning. The 
EEC system lightning and High-Intensity Radiated Fields (HIRF) effects 
that result in LOTC/LOPC should be considered catastrophic.
    c. The components of the installation must be constructed, 
arranged, and installed so as to ensure their continued safe operation 
between normal inspections or overhauls.
    d. Functions incorporated into any electronic engine control that 
make it part of any equipment, systems or installation whose functions 
are beyond that of basic engine control, and which may also introduce 
system failures and malfunctions, are not exempt from Sec.  23.1309 and 
must be shown to meet part 23 levels of safety as derived from Sec.  
23.1309. Part 33 certification data, if applicable, may be used to show 
compliance with any part 23 requirements. If part 33 data is to be used 
to substantiate compliance with part 23 requirements, then the part 23 
applicant must be able to provide this data for their showing of 
compliance.

    Note:  The term ``probable'' in the context of ``probable 
combination of failures'' does not have the same meaning as in AC 
23.1309-1D. The term ``probable'' in ``probable combination of 
failures'' means ``foreseeable,'' or (in AC 23.1309-1D terms), ``not 
extremely improbable.''


    Issued in Kansas City, Missouri on October 28, 2011.
John Colomy,
Acting Manager, Small Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2011-28616 Filed 11-21-11; 8:45 am]
BILLING CODE 4910-13-P

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.