Airworthiness Directives; The Boeing Company Model MD-90-30 Airplanes, 35342-35344 [2011-14339]

Download as PDF 35342 Federal Register / Vol. 76, No. 117 / Friday, June 17, 2011 / Rules and Regulations Avenue, SW., Renton, Washington 98057– 3356; telephone (425) 227–1137; fax (425) 227–1149. Information may be e-mailed to: 9-ANM-116-AMOC-REQUESTS@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/ certificate holding district office. The AMOC approval letter must specifically reference this AD. (2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service. Related Information (m) Refer to MCAI EASA Airworthiness Directive 2010–0159, dated August 3, 2010; and Fokker Service Bulletin SBF100–28–050, Revision 1, dated July 28, 2010; for related information. Material Incorporated by Reference (n) You must use Fokker Service Bulletin SBF100–28–050, Revision 1, dated July 28, 2010, to do the actions required by this AD, unless the AD specifies otherwise. (1) The Director of the Federal Register approved the incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51. (2) For service information identified in this AD, contact Fokker Services B.V., Technical Services Dept., P.O. Box 231, 2150 AE Nieuw-Vennep, the Netherlands; telephone +31 (0)252–627–350; fax +31 (0)252–627–211; e-mail technicalservices.fokkerservices@stork.com; Internet https://www.myfokkerfleet.com. (3) You may review copies of the service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington. For information on the availability of this material at the FAA, call 425–227–1221. (4) You may also review copies of the service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202–741–6030, or go to: https://www.archives.gov/federal_register/ code_of_federal_regulations/ibr_ locations.html. mstockstill on DSK4VPTVN1PROD with RULES Issued in Renton, Washington, on June 2, 2011. Kalene C. Yanamura, Acting Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. 2011–14340 Filed 6–16–11; 8:45 am] BILLING CODE 4910–13–P VerDate Mar<15>2010 18:58 Jun 16, 2011 Jkt 223001 DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2011–0218; Directorate Identifier 2010–NM–164–AD; Amendment 39–16719; AD 2011–12–12] RIN 2120–AA64 Airworthiness Directives; The Boeing Company Model MD–90–30 Airplanes Federal Aviation Administration (FAA), DOT. ACTION: Final rule. AGENCY: We are adopting a new airworthiness directive (AD) for the products listed above. This AD requires a detailed inspection to detect distress and existing repairs to the leading edge structure of the vertical stabilizer at the splice at Station Zfs=52.267; repetitive inspections for cracking in the front spar cap forward flanges of the vertical stabilizer, and either the aft flanges or side skins; repetitive inspections for loose and missing fasteners; and related investigative and corrective actions if necessary. This AD was prompted by reports of cracked vertical stabilizer skin, a severed front spar cap, elongated fastener holes at the leading edge of the vertical stabilizer, and cracked front spar web and front spar cap bolt holes in the vertical stabilizer. We are issuing this AD to detect and correct such cracking damage, which could result in the structure being unable to support limit load, and could lead to the loss of the vertical stabilizer. DATES: This AD is effective July 22, 2011. The Director of the Federal Register approved the incorporation by reference of a certain publication listed in the AD as of July 22, 2011. ADDRESSES: For service information identified in this AD, contact Boeing Commercial Airplanes, Attention: Data & Services Management, 3855 Lakewood Boulevard, MC D800–0019, Long Beach, California 90846–0001; phone: 206–544–5000, extension 2; fax: 206–766–5683; e-mail: dse.boecom@boeing.com; Internet: https://www.myboeingfleet.com. You may review copies of the referenced service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington. For information on the availability of SUMMARY: PO 00000 Frm 00042 Fmt 4700 Sfmt 4700 this material at the FAA, call 425–227– 1221. Examining the AD Docket You may examine the AD docket on the Internet at https:// www.regulations.gov; or in person at the Docket Management Facility between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this AD, the regulatory evaluation, any comments received, and other information. The address for the Docket Office (phone: 800–647–5527) is Document Management Facility, U.S. Department of Transportation, Docket Operations, M–30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue, SE., Washington, DC 20590. FOR FURTHER INFORMATION CONTACT: Roger Durbin, Aerospace Engineer, Airframe Branch, ANM–120L, Los Angeles ACO, 3960 Paramount Blvd, Lakewood, CA 90712–4137; phone: 562–627–5233; fax: 562–627–5210; email: Roger.Durbin@faa.gov. SUPPLEMENTARY INFORMATION: Discussion We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR part 39 to include an airworthiness directive (AD) that would apply to the specified products. That NPRM published in the Federal Register on March 14, 2011 (76 FR 13546). That NPRM proposed to require a detailed inspection to detect distress in, and existing repairs to, the leading edge structure of the vertical stabilizer at the splice at Station Zfs=52.267, and corrective action if necessary. Comments We gave the public the opportunity to participate in developing this AD. We have considered the comment received. The Boeing Company supports the NPRM. Conclusion We reviewed the relevant data, considered the comment received, and determined that air safety and the public interest require adopting the AD as proposed. Costs of Compliance We estimate that this AD affects 19 airplanes of U.S. registry. We estimate the following costs to comply with this AD: E:\FR\FM\17JNR1.SGM 17JNR1 Federal Register / Vol. 76, No. 117 / Friday, June 17, 2011 / Rules and Regulations 35343 ESTIMATED COSTS Action Labor cost Inspection for existing repairs, distress. Repetitive inspections for cracking and loose and missing fasteners. 10 work-hours × $85 per hour = $850. 7 work-hours × $85 per hour = $595 per inspection cycle. We have received no definitive data that would enable us to provide cost estimates for the on-condition action specified in this AD. Authority for This Rulemaking mstockstill on DSK4VPTVN1PROD with RULES $850 ........................................ $16,150. 0 $595 per inspection cycle ....... $11,305 per inspection cycle. Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety. Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows: PART 39—AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows: ■ Authority: 49 U.S.C. 106(g), 40113, 44701. [Amended] 2. The FAA amends § 39.13 by adding the following new airworthiness directive (AD): ■ 2011–12–12 The Boeing Company: Amendment 39–16719; Docket No. FAA–2011–0218; Directorate Identifier 2010–NM–164–AD. Effective Date (a) This AD is effective July 22, 2011. Regulatory Findings Affected ADs This AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government. For the reasons discussed above, I certify that this AD: (1) Is not a ‘‘significant regulatory action’’ under Executive Order 12866, (2) Is not a ‘‘significant rule’’ under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979), (3) Will not affect intrastate aviation in Alaska, and (4) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. 18:58 Jun 16, 2011 $0 List of Subjects in 14 CFR Part 39 § 39.13 Jkt 223001 (b) None. Applicability (c) This AD applies to The Boeing Company Model MD–90–30 airplanes, certificated in any category, as identified in Boeing Alert Service Bulletin MD90–55A014, dated June 24, 2010. Subject (d) Joint Aircraft System Component (JASC)/Air Transport Association (ATA) of America Code 55: Stabilizers. Unsafe Condition (e) This AD was prompted by reports of cracked vertical stabilizer skin, a severed front spar cap, elongated fastener holes at the leading edge of the vertical stabilizer, and cracked front spar web and front spar cap bolt holes in the vertical stabilizer. We are issuing this AD to detect and correct such cracking damage, which could result in the structure being unable to support limit load, and could lead to the loss of the vertical stabilizer. PO 00000 Frm 00043 Cost on U.S. operators Cost per product Adoption of the Amendment Title 49 of the United States Code specifies the FAA’s authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII: Aviation Programs, describes in more detail the scope of the Agency’s authority. We are issuing this rulemaking under the authority described in subtitle VII, part A, subpart III, section 44701: ‘‘General requirements.’’ Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. VerDate Mar<15>2010 Parts cost Fmt 4700 Sfmt 4700 Compliance (f) Comply with this AD within the compliance times specified, unless already done. Inspections for Distress/Repairs (g) Within 4,100 flight cycles after the effective date of this AD, do a detailed inspection for distress in and existing repairs to the leading edge structure of the vertical stabilizer at the splice at Station Zfs=52.267, in accordance with the Accomplishment Instructions of Boeing Alert Service Bulletin MD90–55A014, dated June 24, 2010. Repetitive Inspections for Cracks, and Related Investigative and Corrective Actions (h) Before further flight after doing the inspection required by paragraph (g) of this AD, inspect for cracks of the left and right vertical stabilizer front spar cap, in accordance with either Option 1 or Option 2 as specified in the Accomplishment Instructions of Boeing Alert Service Bulletin MD90–55A014, dated June 24, 2010. If any crack is found, before further flight, evaluate and verify to confirm all crack indications, in accordance with the Accomplishment Instructions of Boeing Alert Service Bulletin MD90–55A014, dated June 24, 2010. (1) If any cracking is confirmed, before further flight, repair using a method approved in accordance with the procedures specified in paragraph (l) of this AD. (2) If no cracking is confirmed, repeat the inspection thereafter at intervals not to exceed the applicable interval specified in paragraph (h)(2)(i) or (h)(2)(ii) of this AD. (i) If the most recent inspection was done using Option 1, the next inspection must be done within 4,400 flight cycles. (ii) If the most recent inspection was done using Option 2, the next inspection must be done within 3,000 flight cycles. Leading Edge Repair (i) If leading edge distress is found during the detailed inspection required by paragraph (g) of this AD, before further flight and after accomplishing the inspection required by paragraph (h) of this AD, repair the leading edge, in accordance with the Accomplishment Instructions of Boeing Alert Service Bulletin MD90–55A014, dated June 24, 2010. Inspection for Loose/Missing Fasteners (j) For airplanes on which no cracking is confirmed during the initial inspection required by paragraph (h) of this AD: At the applicable time specified in paragraph (j)(1) or (j)(2) of this AD, do a detailed inspection for indications of loose and missing fasteners, in accordance with the Accomplishment E:\FR\FM\17JNR1.SGM 17JNR1 35344 Federal Register / Vol. 76, No. 117 / Friday, June 17, 2011 / Rules and Regulations mstockstill on DSK4VPTVN1PROD with RULES Instructions of Boeing Alert Service Bulletin MD90–55A014, dated June 24, 2010. If any loose or missing fastener is found, before further flight, repair the leading edge, in accordance with the Accomplishment Instructions of Boeing Alert Service Bulletin MD90–55A014, dated June 24, 2010. (1) If the inspection required by paragraph (h) was done using Option 1, do the inspection required by paragraph (j) of this AD within 4,400 flight cycles after accomplishing the inspection required by paragraph (h) of this AD. (2) If inspection required by paragraph (h) was done using Option 2, do the inspection required by paragraph (j) of this AD within 3,000 flight cycles after accomplishing the inspection required by paragraph (h) of this AD. (k) For airplanes on which no cracking is confirmed during the most recent inspection required by paragraph (h) of this AD: Repeat the inspection for loose and missing fasteners required by paragraph (j) of this AD thereafter at intervals not to exceed the applicable time specified in paragraph (k)(1) or (k)(2) of this AD. (1) If the most recent inspection required by paragraph (h) was done using Option 1, the next inspection required by paragraph (j) of this AD must be done within 4,400 flight cycles after accomplishing the most recent inspection required by paragraph (j) of this AD. (2) If the most recent inspection required by paragraph (h) was done using Option 2, the next inspection required by paragraph (j) of this AD must be done within 3,000 flight cycles after the most recent inspection required by paragraph (j) of this AD. Material Incorporated by Reference (n) You must use of Boeing Alert Service Bulletin MD90–55A014, dated June 24, 2010, to do the actions required by this AD, unless the AD specifies otherwise. (1) The Director of the Federal Register approved the incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51. (2) For service information identified in this AD, contact Boeing Commercial Airplanes, Attention: Data & Services Management, 3855 Lakewood Boulevard, MC D800–0019, Long Beach, California 90846– 0001; phone: 206–544–5000, extension 2; fax: 206–766–5683; e-mail: dse.boecom@boeing.com; Internet: https:// www.myboeingfleet.com. (3) You may review copies of the service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington. For information on the availability of this material at the FAA, call 425–227–1221. (4) You may also review copies of the service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at an NARA facility, call 202–741– 6030, or go to https://www.archives.gov/ federal_register/code_of_federal_regulations/ ibr_locations.html. Alternative Methods of Compliance (AMOCs) (l)(1) The Manager, Los Angeles Aircraft Certification Office, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the manager of the ACO, send it to the attention of the person identified in the Related Information section of this AD. (2) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/ certificate holding district office. (3) An AMOC that provides an acceptable level of safety may be used for any repair required by this AD if it is approved by the Boeing Commercial Airplanes Organization Designation Authorization (ODA) that has been authorized by the Manager, Los Angeles ACO to make those findings. For a repair method to be approved, the repair must meet the certification basis of the airplane, and the approval must specifically refer to this AD. [FR Doc. 2011–14339 Filed 6–16–11; 8:45 am] Related Information (m) For more information about this AD, contact Roger Durbin, Aerospace Engineer, Airframe Branch, ANM–120L, Los Angeles ACO, 3960 Paramount Blvd., Lakewood, CA 90712–4137; phone: 562–627–5233; fax: 562– 627–5210; e-mail: Roger.Durbin@faa.gov. VerDate Mar<15>2010 18:58 Jun 16, 2011 Jkt 223001 Issued in Renton, Washington, on May 31, 2011. Jeffrey E. Duven, Acting Manager, Transport Airplane Directorate, Aircraft Certification Service. BILLING CODE 4910–13–P DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2011–0326; Directorate Identifier 2011–CE–006–AD; Amendment 39–16725; AD 2011–13–02] RIN 2120–AA64 Airworthiness Directives; Costruzioni Aeronautiche Tecnam srl Model P2006T Airplanes Federal Aviation Administration (FAA), Department of Transportation (DOT). ACTION: Final rule. AGENCY: We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: SUMMARY: PO 00000 Frm 00044 Fmt 4700 Sfmt 4700 During Landing Gear retraction/extension ground checks performed on the P2006T, a loose Seeger ring was found on the nose landing gear hydraulic actuator cap. The manufacturer has identified the root cause of this discrepancy in a design deficiency of the hydraulic actuator caps. This condition, if not corrected, could determine uncommanded and improper extension of the nose or main landing gear. We are issuing this AD to require actions to correct the unsafe condition on these products. DATES: This AD becomes effective July 22, 2011. On July 22, 2011, the Director of the Federal Register approved the incorporation by reference of certain publications listed in this AD. ADDRESSES: You may examine the AD docket on the Internet at https:// www.regulations.gov or in person at Document Management Facility, U.S. Department of Transportation, Docket Operations, M–30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue, SE., Washington, DC 20590. For service information identified in this AD, contact Costruzioni Aeronautiche TECNAM Airworthiness Office, Via Maiorise—81043 Capua (CE) Italy; telephone: +39 0823 620134; fax: +39 0823 622899; e-mail: m.oliva@tecnam.com, p.violetti@tecnam.com; internet: http:/www.tecnam.com. You may review copies of the referenced service information at the FAA, Small Airplane Directorate, 901 Locust, Kansas City, Missouri 64106. For information on the availability of this material at the FAA, call 816–329–4148. FOR FURTHER INFORMATION CONTACT: Albert Mercado, Aerospace Engineer, FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 329– 4119; fax: (816) 329–4090. SUPPLEMENTARY INFORMATION: Discussion We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR part 39 to include an AD that would apply to the specified products. That NPRM was published in the Federal Register on April 6, 2011 (76 FR 18964). That NPRM proposed to correct an unsafe condition for the specified products. The MCAI states: During Landing Gear retraction/extension ground checks performed on the P2006T, a loose Seeger ring was found on the nose landing gear hydraulic actuator cap. The manufacturer has identified the root cause of this discrepancy in a design deficiency of the hydraulic actuator caps. This condition, if not corrected, could determine uncommanded and improper E:\FR\FM\17JNR1.SGM 17JNR1

Agencies

[Federal Register Volume 76, Number 117 (Friday, June 17, 2011)]
[Rules and Regulations]
[Pages 35342-35344]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2011-14339]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2011-0218; Directorate Identifier 2010-NM-164-AD; 
Amendment 39-16719; AD 2011-12-12]
RIN 2120-AA64


Airworthiness Directives; The Boeing Company Model MD-90-30 
Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: We are adopting a new airworthiness directive (AD) for the 
products listed above. This AD requires a detailed inspection to detect 
distress and existing repairs to the leading edge structure of the 
vertical stabilizer at the splice at Station Zfs=52.267; repetitive 
inspections for cracking in the front spar cap forward flanges of the 
vertical stabilizer, and either the aft flanges or side skins; 
repetitive inspections for loose and missing fasteners; and related 
investigative and corrective actions if necessary. This AD was prompted 
by reports of cracked vertical stabilizer skin, a severed front spar 
cap, elongated fastener holes at the leading edge of the vertical 
stabilizer, and cracked front spar web and front spar cap bolt holes in 
the vertical stabilizer. We are issuing this AD to detect and correct 
such cracking damage, which could result in the structure being unable 
to support limit load, and could lead to the loss of the vertical 
stabilizer.

DATES: This AD is effective July 22, 2011.
    The Director of the Federal Register approved the incorporation by 
reference of a certain publication listed in the AD as of July 22, 
2011.

ADDRESSES: For service information identified in this AD, contact 
Boeing Commercial Airplanes, Attention: Data & Services Management, 
3855 Lakewood Boulevard, MC D800-0019, Long Beach, California 90846-
0001; phone: 206-544-5000, extension 2; fax: 206-766-5683; e-mail: 
dse.boecom@boeing.com; Internet: https://www.myboeingfleet.com. You may 
review copies of the referenced service information at the FAA, 
Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, 
Washington. For information on the availability of this material at the 
FAA, call 425-227-1221.

Examining the AD Docket

    You may examine the AD docket on the Internet at https://www.regulations.gov; or in person at the Docket Management Facility 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The AD docket contains this AD, the regulatory evaluation, 
any comments received, and other information. The address for the 
Docket Office (phone: 800-647-5527) is Document Management Facility, 
U.S. Department of Transportation, Docket Operations, M-30, West 
Building Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE., 
Washington, DC 20590.

FOR FURTHER INFORMATION CONTACT: Roger Durbin, Aerospace Engineer, 
Airframe Branch, ANM-120L, Los Angeles ACO, 3960 Paramount Blvd, 
Lakewood, CA 90712-4137; phone: 562-627-5233; fax: 562-627-5210; e-
mail: Roger.Durbin@faa.gov.

SUPPLEMENTARY INFORMATION:

Discussion

    We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR 
part 39 to include an airworthiness directive (AD) that would apply to 
the specified products. That NPRM published in the Federal Register on 
March 14, 2011 (76 FR 13546). That NPRM proposed to require a detailed 
inspection to detect distress in, and existing repairs to, the leading 
edge structure of the vertical stabilizer at the splice at Station 
Zfs=52.267, and corrective action if necessary.

Comments

    We gave the public the opportunity to participate in developing 
this AD. We have considered the comment received. The Boeing Company 
supports the NPRM.

Conclusion

    We reviewed the relevant data, considered the comment received, and 
determined that air safety and the public interest require adopting the 
AD as proposed.

Costs of Compliance

    We estimate that this AD affects 19 airplanes of U.S. registry.
    We estimate the following costs to comply with this AD:

[[Page 35343]]



                                                 Estimated Costs
----------------------------------------------------------------------------------------------------------------
                                                                                                Cost on U.S.
              Action                    Labor cost        Parts cost    Cost per product          operators
----------------------------------------------------------------------------------------------------------------
Inspection for existing repairs,   10 work-hours x $85            $0  $850................  $16,150.
 distress.                          per hour = $850.
Repetitive inspections for         7 work-hours x $85              0  $595 per inspection   $11,305 per
 cracking and loose and missing     per hour = $595 per                cycle.                inspection cycle.
 fasteners.                         inspection cycle.
----------------------------------------------------------------------------------------------------------------

    We have received no definitive data that would enable us to provide 
cost estimates for the on-condition action specified in this AD.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII: Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
subtitle VII, part A, subpart III, section 44701: ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    This AD will not have federalism implications under Executive Order 
13132. This AD will not have a substantial direct effect on the States, 
on the relationship between the national government and the States, or 
on the distribution of power and responsibilities among the various 
levels of government.
    For the reasons discussed above, I certify that this AD:
    (1) Is not a ``significant regulatory action'' under Executive 
Order 12866,
    (2) Is not a ``significant rule'' under DOT Regulatory Policies and 
Procedures (44 FR 11034, February 26, 1979),
    (3) Will not affect intrastate aviation in Alaska, and
    (4) Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. The FAA amends Sec.  39.13 by adding the following new airworthiness 
directive (AD):

2011-12-12 The Boeing Company: Amendment 39-16719; Docket No. FAA-
2011-0218; Directorate Identifier 2010-NM-164-AD.

Effective Date

    (a) This AD is effective July 22, 2011.

Affected ADs

    (b) None.

Applicability

    (c) This AD applies to The Boeing Company Model MD-90-30 
airplanes, certificated in any category, as identified in Boeing 
Alert Service Bulletin MD90-55A014, dated June 24, 2010.

Subject

    (d) Joint Aircraft System Component (JASC)/Air Transport 
Association (ATA) of America Code 55: Stabilizers.

Unsafe Condition

    (e) This AD was prompted by reports of cracked vertical 
stabilizer skin, a severed front spar cap, elongated fastener holes 
at the leading edge of the vertical stabilizer, and cracked front 
spar web and front spar cap bolt holes in the vertical stabilizer. 
We are issuing this AD to detect and correct such cracking damage, 
which could result in the structure being unable to support limit 
load, and could lead to the loss of the vertical stabilizer.

Compliance

    (f) Comply with this AD within the compliance times specified, 
unless already done.

Inspections for Distress/Repairs

    (g) Within 4,100 flight cycles after the effective date of this 
AD, do a detailed inspection for distress in and existing repairs to 
the leading edge structure of the vertical stabilizer at the splice 
at Station Zfs=52.267, in accordance with the Accomplishment 
Instructions of Boeing Alert Service Bulletin MD90-55A014, dated 
June 24, 2010.

Repetitive Inspections for Cracks, and Related Investigative and 
Corrective Actions

    (h) Before further flight after doing the inspection required by 
paragraph (g) of this AD, inspect for cracks of the left and right 
vertical stabilizer front spar cap, in accordance with either Option 
1 or Option 2 as specified in the Accomplishment Instructions of 
Boeing Alert Service Bulletin MD90-55A014, dated June 24, 2010. If 
any crack is found, before further flight, evaluate and verify to 
confirm all crack indications, in accordance with the Accomplishment 
Instructions of Boeing Alert Service Bulletin MD90-55A014, dated 
June 24, 2010.
    (1) If any cracking is confirmed, before further flight, repair 
using a method approved in accordance with the procedures specified 
in paragraph (l) of this AD.
    (2) If no cracking is confirmed, repeat the inspection 
thereafter at intervals not to exceed the applicable interval 
specified in paragraph (h)(2)(i) or (h)(2)(ii) of this AD.
    (i) If the most recent inspection was done using Option 1, the 
next inspection must be done within 4,400 flight cycles.
    (ii) If the most recent inspection was done using Option 2, the 
next inspection must be done within 3,000 flight cycles.

Leading Edge Repair

    (i) If leading edge distress is found during the detailed 
inspection required by paragraph (g) of this AD, before further 
flight and after accomplishing the inspection required by paragraph 
(h) of this AD, repair the leading edge, in accordance with the 
Accomplishment Instructions of Boeing Alert Service Bulletin MD90-
55A014, dated June 24, 2010.

Inspection for Loose/Missing Fasteners

    (j) For airplanes on which no cracking is confirmed during the 
initial inspection required by paragraph (h) of this AD: At the 
applicable time specified in paragraph (j)(1) or (j)(2) of this AD, 
do a detailed inspection for indications of loose and missing 
fasteners, in accordance with the Accomplishment

[[Page 35344]]

Instructions of Boeing Alert Service Bulletin MD90-55A014, dated 
June 24, 2010. If any loose or missing fastener is found, before 
further flight, repair the leading edge, in accordance with the 
Accomplishment Instructions of Boeing Alert Service Bulletin MD90-
55A014, dated June 24, 2010.
    (1) If the inspection required by paragraph (h) was done using 
Option 1, do the inspection required by paragraph (j) of this AD 
within 4,400 flight cycles after accomplishing the inspection 
required by paragraph (h) of this AD.
    (2) If inspection required by paragraph (h) was done using 
Option 2, do the inspection required by paragraph (j) of this AD 
within 3,000 flight cycles after accomplishing the inspection 
required by paragraph (h) of this AD.
    (k) For airplanes on which no cracking is confirmed during the 
most recent inspection required by paragraph (h) of this AD: Repeat 
the inspection for loose and missing fasteners required by paragraph 
(j) of this AD thereafter at intervals not to exceed the applicable 
time specified in paragraph (k)(1) or (k)(2) of this AD.
    (1) If the most recent inspection required by paragraph (h) was 
done using Option 1, the next inspection required by paragraph (j) 
of this AD must be done within 4,400 flight cycles after 
accomplishing the most recent inspection required by paragraph (j) 
of this AD.
    (2) If the most recent inspection required by paragraph (h) was 
done using Option 2, the next inspection required by paragraph (j) 
of this AD must be done within 3,000 flight cycles after the most 
recent inspection required by paragraph (j) of this AD.

Alternative Methods of Compliance (AMOCs)

    (l)(1) The Manager, Los Angeles Aircraft Certification Office, 
FAA, has the authority to approve AMOCs for this AD, if requested 
using the procedures found in 14 CFR 39.19. In accordance with 14 
CFR 39.19, send your request to your principal inspector or local 
Flight Standards District Office, as appropriate. If sending 
information directly to the manager of the ACO, send it to the 
attention of the person identified in the Related Information 
section of this AD.
    (2) Before using any approved AMOC, notify your appropriate 
principal inspector, or lacking a principal inspector, the manager 
of the local flight standards district office/certificate holding 
district office.
    (3) An AMOC that provides an acceptable level of safety may be 
used for any repair required by this AD if it is approved by the 
Boeing Commercial Airplanes Organization Designation Authorization 
(ODA) that has been authorized by the Manager, Los Angeles ACO to 
make those findings. For a repair method to be approved, the repair 
must meet the certification basis of the airplane, and the approval 
must specifically refer to this AD.

Related Information

    (m) For more information about this AD, contact Roger Durbin, 
Aerospace Engineer, Airframe Branch, ANM-120L, Los Angeles ACO, 3960 
Paramount Blvd., Lakewood, CA 90712-4137; phone: 562-627-5233; fax: 
562-627-5210; e-mail: Roger.Durbin@faa.gov.

Material Incorporated by Reference

    (n) You must use of Boeing Alert Service Bulletin MD90-55A014, 
dated June 24, 2010, to do the actions required by this AD, unless 
the AD specifies otherwise.
    (1) The Director of the Federal Register approved the 
incorporation by reference of this service information under 5 
U.S.C. 552(a) and 1 CFR part 51.
    (2) For service information identified in this AD, contact 
Boeing Commercial Airplanes, Attention: Data & Services Management, 
3855 Lakewood Boulevard, MC D800-0019, Long Beach, California 90846-
0001; phone: 206-544-5000, extension 2; fax: 206-766-5683; e-mail: 
dse.boecom@boeing.com; Internet: https://www.myboeingfleet.com.
    (3) You may review copies of the service information at the FAA, 
Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, 
Washington. For information on the availability of this material at 
the FAA, call 425-227-1221.
    (4) You may also review copies of the service information that 
is incorporated by reference at the National Archives and Records 
Administration (NARA). For information on the availability of this 
material at an NARA facility, call 202-741-6030, or go to https://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.

    Issued in Renton, Washington, on May 31, 2011.
Jeffrey E. Duven,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 2011-14339 Filed 6-16-11; 8:45 am]
BILLING CODE 4910-13-P
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.