Medical Devices; General and Plastic Surgery Devices; Classification of the Low Level Laser System for Aesthetic Use, 20840-20842 [2011-8944]
Download as PDF
20840
Federal Register / Vol. 76, No. 72 / Thursday, April 14, 2011 / Rules and Regulations
interconnection-related system impact
studies.
10. Similarly, we deny TAPS’s request
that the information from system impact
studies be made available on a nondiscriminatory basis to all interested
transmission customers. TAPS
erroneously assumes that the
Commission determined that system
impact studies (or other studies)
performed in response to
interconnection requests are planning
activities that may be conducted by
marketing function employees.
Marketing function employees may not
perform system impact studies (or other
studies) in response to interconnection
requests since the studies would involve
the use and analysis of non-public
transmission information. As we stated
in Order No. 717, planning personnel
who do not qualify as marketing
function employees may discuss
information with transmission function
employees.12 However, we reiterated
that the No Conduit Rule applied in this
situation, stating that if transmission
employees share transmission function
information with planning personnel,
the planning personnel may not pass
such information on to marketing
function employees. The clear
implication of these statements is that
while planning studies may be
conducted by personnel who are not
transmission function employees,
marketing function employees may not
participate in the preparation of studies
which involve the use and analysis of
non-public transmission information.13
11. We grant TAPS’s clarification
request that when an employee
performs a system impact study in
response to a transmission service
request, that employee is a transmission
function employee regardless of the
duration of the requested transmission
service. This clarification is consistent
with our previous conclusion that the
designation of an employee as a
transmission function employee does
not depend upon the duration of the
requested transmission service.14
mstockstill on DSKH9S0YB1PROD with RULES
III. Document Availability
12. In addition to publishing the full
text of this document in the Federal
12 Order No. 717, FERC Stats. & Regs ¶ 31,280 at
P 151.
13 Order No. 717 specifically recognized that there
are employees who are neither transmission
function employees nor marketing function
employees. See, e.g., Order No. 717, FERC Stats. &
Regs. ¶ 31,280 at P 174 (‘‘Transmission function
employees are no longer barred from interacting
with all the employees of a marketing or energy
affiliate (only marketing function employees)’’).
14 See Standards of Conduct for Transmission
Providers, Order No. 717–A, 74 FR 54463 (Oct. 22,
2009), FERC Stats. & Regs. ¶ 31,297, at P 27 (2009).
VerDate Mar<15>2010
17:30 Apr 13, 2011
Jkt 223001
Register, the Commission provides all
interested persons an opportunity to
view and/or print the contents of this
document via the Internet through
FERC’s Home Page (https://www.ferc.gov)
and in FERC’s Public Reference Room
during normal business hours (8:30 a.m.
to 5 p.m. Eastern time) at 888 First
Street, NE., Room 2A, Washington, DC
20426.
13. From FERC’s Home Page on the
Internet, this information is available on
eLibrary. The full text of this document
is available on eLibrary in PDF and
Microsoft Word format for viewing,
printing, and/or downloading. To access
this document in eLibrary, type the
docket number excluding the last three
digits of this document in the docket
number field.
14. User assistance is available for
eLibrary and the FERC’s website during
normal business hours from FERC
Online Support at 202–502–6652 (toll
free at 1–866–208–3676) or e-mail at
ferconlinesupport@ferc.gov, or the
Public Reference Room at (202) 502–
8371, TTY (202) 502–8659. E-mail the
Public Reference Room at
public.referenceroom@ferc.gov.
IV. Effective Date
15. Changes to Order No. 717–C
adopted in this order on rehearing and
clarification are effective May 16, 2011.
By the Commission.
Kimberly D. Bose,
Secretary.
[FR Doc. 2011–9059 Filed 4–13–11; 8:45 am]
BILLING CODE 6717–01–P
DEPARTMENT OF HEALTH AND
HUMAN SERVICES
Food and Drug Administration
21 CFR Part 878
[Docket No. FDA–2011–N–0188]
Medical Devices; General and Plastic
Surgery Devices; Classification of the
Low Level Laser System for Aesthetic
Use
AGENCY:
Food and Drug Administration,
HHS.
ACTION:
Final rule.
The Food and Drug
Administration (FDA) is classifying the
low level laser system for aesthetic use
into class II (special controls). The
special control(s) that will apply to the
device is entitled ‘‘Class II Special
Controls Guidance Document: Low
Level Laser System for Aesthetic Use.’’
The Agency is classifying the device
SUMMARY:
PO 00000
Frm 00006
Fmt 4700
Sfmt 4700
into class II (special controls) in order
to provide a reasonable assurance of
safety and effectiveness of the device.
Elsewhere in this issue of the Federal
Register, FDA is announcing the
availability of a guidance document that
will serve as the special control for this
device type.
DATES: This rule is effective May 16,
2011. The classification was effective on
August 24, 2010.
FOR FURTHER INFORMATION CONTACT:
Richard Felten, Center for Devices and
Radiological Health, Food and Drug
Administration, 10903 New Hampshire
Ave., Bldg. 66, Rm. 1436, Silver Spring,
MD 20993–0002, 301–796–6392.
SUPPLEMENTARY INFORMATION:
I. What is the background of this
rulemaking?
In accordance with section 513(f)(1) of
the Federal Food, Drug, and Cosmetic
Act (the FD&C Act) (21 U.S.C.
360c(f)(1)), devices that were not in
commercial distribution before May 28,
1976 (the date of enactment of the
Medical Device Amendments of 1976),
generally referred to as postamendments
devices, are classified automatically by
statute into class III without any FDA
rulemaking process. These devices
remain in class III and require
premarket approval, unless and until
the device is classified or reclassified
into class I or II, or FDA issues an order
finding the device to be substantially
equivalent, in accordance with section
513(i) of the FD&C Act, to a predicate
device that does not require premarket
approval. The Agency determines
whether new devices are substantially
equivalent to predicate devices by
means of premarket notification
procedures in section 510(k) of the
FD&C Act (21 U.S.C. 360(k)) and 21 CFR
part 807 of the regulations.
Section 513(f)(2) of the FD&C Act
provides that any person who submits a
premarket notification under section
510(k) of the FD&C Act for a device that
has not previously been classified may,
within 30 days after receiving an order
classifying the device into class III
under section 513(f)(1) of the FD&C Act,
request FDA to classify the device under
the criteria set forth in section 513(a)(1)
of the FD&C Act. FDA will, within 60
days of receiving this request, classify
the device by written order. This
classification will be the initial
classification of the device. Within 30
days after the issuance of an order
classifying the device, FDA must
publish a notice in the Federal Register
announcing this classification.
In accordance with section 513(f)(1) of
the FD&C Act, FDA issued an order on
E:\FR\FM\14APR1.SGM
14APR1
Federal Register / Vol. 76, No. 72 / Thursday, April 14, 2011 / Rules and Regulations
December 22, 2008, classifying the
Erchonia Low Level Laser System for
Aesthetic Use into class III because it
was not substantially equivalent to a
device that was introduced or delivered
for introduction into interstate
commerce for commercial distribution
before May 28, 1976, or a device which
was subsequently reclassified into class
I or class II. On January 5, 2009,
Erchonia, Inc., submitted a petition
requesting classification of the Erchonia
Low Level Laser System for Aesthetic
Use under section 513(f)(2) of the FD&C
Act. The manufacturer recommended
that the device be classified into class II.
(Ref. 1)
In accordance with section 513(f)(2) of
the FD&C Act, FDA reviewed the
petition in order to classify the device
under the criteria for classification set
forth in section 513(a)(1) of the FD&C
Act. FDA classifies devices into class II
if general controls by themselves are
insufficient to provide reasonable
assurance of safety and effectiveness,
but there is sufficient information to
establish special controls to provide
reasonable assurance of the safety and
effectiveness of the device for its
intended use. After review of the
information submitted in the petition,
FDA determined that the device can be
classified into class II with the
establishment of special controls. FDA
believes these special controls will
provide reasonable assurance of the
safety and effectiveness of the device.
The device is assigned the generic
name Low Level Laser System for
Aesthetic Use, and it is identified as a
device using low level laser energy for
the disruption of adipocyte cells within
the fat layer for the release of fat and
lipids from these cells for noninvasive
aesthetic use.
FDA has identified the following risks
to health associated specifically with
this type of device and the
recommended measures to mitigate
these risks.
• Ocular injury is a recognized hazard
from laser optical systems because of
the unique physical characteristics of
laser light; that is, this optical radiation
is easily transmitted into the eye as a
very bright, intense light beam that may
produce lesions on the retina. This
hazard is addressed by device labeling,
which includes recommendations for
not looking directly at the laser beam
and the wearing of appropriate laser
safety eyewear by both the user and
patient. The labeling also includes
information defining the size of the area
within which this optical hazard exists.
• Electrical shock is addressed by
recommended testing of the device
according to recognized U.S. and
international standards specifically
designed to determine and measure
potential electrical safety. Again, the
recommended device labeling also
includes specific warnings for the user
in terms of device placement,
appropriate electrical wiring needs,
reminders to periodically check device
20841
wiring and accessories for damage, and
avoidance of use of the device in
environments where electrical shock is
possible.
• Unintended cell damage is a
potential risk from use of low level
lasers if improper or incorrect energy is
used to initiate the process of causing
lipid and fat leakage from the target
adipocyte cells. The intended effect on
the adipocyte cells is the creation of
pores that results in the lipid or fat
leaving these specialized cells; however,
if the laser parameters are not correct,
no effect may occur in terms of
adipocyte change or other nonadipocyte cells may be affected,
resulting in alteration of other cellular
membranes or transport systems that
could result in unintended cell death.
• Use error represents those risks to
the patient that can occur from
improper use of the device. In order to
address this potential risk, we
recommend the manufacturer provide a
detailed operator manual, which
contains information on possible risks
and hazards and how these should be
avoided and clear recommended safe
treatment procedures that include
information on device settings for
treatment, clear information on how the
device is to be used during treatment,
and recommended posttreatment care.
FDA believes that the class II special
controls guidance document will aid in
mitigating the potential risks to health
as described in table 1 of this document.
TABLE 1—RISKS TO HEALTH AND MITIGATION MEASURES
Identified risk
Recommended mitigation measures
Ocular Injury .............................................................................................
Section 6. Bench Testing.
Section 7. Software Validation.
Section 8. Clinical Testing.
Section 12. Labeling.
Section 11. Electrical and Mechanical Safety Performance Testing (IEC
60601–1).
Section 12. Labeling.
Section 6. Bench Testing.
Section 7. Software Validation.
Section 8. Clinical Testing.
Section 9. Biocompatibility.
Section 10. Electromagnetic Compatibility (IEC 60601–1–2).
Section 12. Labeling.
Section 12. Labeling.
Electrical Shock ........................................................................................
Unintended Cell Damage .........................................................................
mstockstill on DSKH9S0YB1PROD with RULES
Use Error ..................................................................................................
FDA believes that the special controls
guidance, ‘‘Low Level Laser System for
Aesthetic Use,’’ in addition to general
controls, address the risks to health and
provide reasonable assurance of the
safety and effectiveness of the device.
Therefore, on August 24, 2010, FDA
issued an order to the petitioner
classifying the device into class II. FDA
VerDate Mar<15>2010
17:30 Apr 13, 2011
Jkt 223001
is codifying the classification of the
device by adding § 878.5400.
Following the effective date of this
final classification rule, any firm
submitting a 510(k) premarket
notification for low level laser system
for aesthetic use will need to address
the issues covered in the special
controls guidance. However, the firm
need only show that its device meets the
PO 00000
Frm 00007
Fmt 4700
Sfmt 4700
recommendations of the guidance or in
some other way provides equivalent
assurance of safety and effectiveness.
Section 510(m) of the FD&C Act
provides that FDA may exempt a class
II device from the premarket notification
requirements under section 510(k) of the
FD&C Act, if FDA determines that
premarket notification is not necessary
to provide reasonable assurance of the
E:\FR\FM\14APR1.SGM
14APR1
20842
Federal Register / Vol. 76, No. 72 / Thursday, April 14, 2011 / Rules and Regulations
safety and effectiveness of the device.
For this type of device, FDA has
determined that premarket notification
is necessary to provide reasonable
assurance of the safety and effectiveness
of the device. Therefore, this device
type is not exempt from premarket
notification requirements. Persons who
intend to market this type of device
must submit to FDA a premarket
notification, prior to marketing the
device, which contains information
about the low level laser system for
aesthetic use they intend to market.
mstockstill on DSKH9S0YB1PROD with RULES
II. What is the environmental impact of
this rule?
The Agency has determined under 21
CFR 25.34(b) that this action is of a type
that does not individually or
cumulatively have a significant effect on
the human environment. Therefore,
neither an environmental assessment
nor an environmental impact statement
is required.
III. What is the analysis of impacts of
this rule?
FDA has examined the impacts of the
final rule under Executive Order 12866
and the Regulatory Flexibility Act (5
U.S.C. 601–612), and the Unfunded
Mandates Reform Act of 1995 (Pub. L.
104–4). Executive Order 12866 directs
Agencies to assess all costs and benefits
of available regulatory alternatives and,
when regulation is necessary, to select
regulatory approaches that maximize
net benefits (including potential
economic, environmental, public health
and safety, and other advantages;
distributive impacts; and equity). The
Agency believes that this final rule is
not a significant regulatory action as
defined by the Executive order and so
it is not subject to review under the
Executive order.
The Regulatory Flexibility Act
requires Agencies to analyze regulatory
options that would minimize any
significant impact of a rule on small
entities. Because reclassification of this
device from class III to class II will
relieve manufacturers of the device of
the cost of complying with the
premarket approval requirements of
section 515 of the FD&C Act (21 U.S.C.
360e), and may permit small potential
competitors to enter the marketplace by
lowering their costs, the Agency
certifies that the final rule will not have
a significant economic impact on a
substantial number of small entities.
Section 202(a) of the Unfunded
Mandates Reform Act of 1995 requires
that Agencies prepare a written
statement, which includes an
assessment of anticipated costs and
benefits, before proposing ‘‘any rule that
VerDate Mar<15>2010
17:30 Apr 13, 2011
Jkt 223001
includes any Federal mandate that may
result in the expenditure by State, local,
and tribal governments, in the aggregate,
or by the private sector, of $100,000,000
or more (adjusted annually for inflation)
in any one year.’’ The current threshold
after adjustment for inflation is $135
million, using the most current (2009)
Implicit Price Deflator for the Gross
Domestic Product. FDA does not expect
this final rule to result in any 1-year
expenditure that would meet or exceed
this amount.
IV. Does this rule have federalism
implications?
FDA has analyzed this final rule in
accordance with the principles set forth
in Executive Order 13132. Section 4(a)
of the Executive order requires Agencies
to ‘‘construe * * * a Federal statute to
preempt State law only where the
statute contains an express preemption
provision or there is some other clear
evidence that the Congress intended
preemption of State law, or where the
exercise of State authority conflicts with
the exercise of Federal authority under
the Federal statute.’’ Federal law
includes an express preemption
provision that preempts certain state
requirements ‘‘different from or in
addition to’’ certain Federal
requirements applicable to devices. (See
section 521 of the FD&C Act (21 U.S.C.
360k); See Medtronic, Inc., v. Lohr, 518
U.S. 470 (1996); and Riegel v.
Medtronic, Inc., 128 S. Ct. 999 (2008)).
The special controls established by this
final rule creates ‘‘requirements’’ for
specific medical devices under 21
U.S.C. 360k, even though product
sponsors have some flexibility in how
they meet those requirements. (See
Papike v. Tambrands, Inc., 107 F.3d
737, 740–42 (9th Cir. 1997)).
V. How does this rule comply with the
Paperwork Reduction Act of 1995?
FDA concludes that this final rule
contains no new collections of
information. Therefore, clearance by the
Office of Management and Budget
(OMB) under the Paperwork Reduction
Act of 1995 (PRA) (44 U.S.C. 3501–
3520) is not required. This final rule
establishes as special controls a
guidance document that refers to
previously approved collections of
information found in other FDA
regulations. These collections of
information are subject to review by
OMB under the PRA. Elsewhere in this
issue of the Federal Register, FDA is
issuing a notice announcing the
availability of the guidance document
entitled ‘‘Class II Special Controls
Guidance Document: Low Level Laser
System for Aesthetic Use’’ that will
PO 00000
Frm 00008
Fmt 4700
Sfmt 9990
serve as the special control for this
device. This notice contains an analysis
of the paperwork burden for the
guidance document.
VI. References
The following references have been
placed on display in the Division of
Dockets Management (HFA–305), Food
and Drug Administration, 5630 Fishers
Lane, rm. 1061, Rockville, MD 20852,
and may be seen by interested persons
between 9 a.m. and 4 p.m., Monday
through Friday.
1. Petition from Erchonia, Inc.,
January 5, 2009.
List of Subjects in 21 CFR Part 878
Medical devices.
Therefore, under the Federal Food,
Drug, and Cosmetic Act and under
authority delegated to the Commissioner
of Food and Drugs, 21 CFR part 878 is
amended as follows:
PART 878—GENERAL AND PLASTIC
SURGERY DEVICES
1. The authority citation for 21 CFR
part 878 continues to read as follows:
■
Authority: 21 U.S.C. 351, 360, 360c, 360e,
360j, 360l, 371.
2. Section 878.5400 is added to
subpart F to read as follows:
■
§ 878.5400 Low Level Laser System for
Aesthetic Use
(a) Identification. A Low Level Laser
System for Aesthetic Use is a device
using low level laser energy for the
disruption of adipocyte cells within the
fat layer for the release of fat and lipids
from these cells for noninvasive
aesthetic use.
(b) Classification. Class II (special
controls). The special control for this
device is the FDA guidance document
entitled ‘‘Guidance for Industry and
Food and Drug Administration Staff;
Class II Special Controls Guidance
Document: Low Level Laser System for
Aesthetic Use.’’ See § 878.1(e) for the
availability of this guidance document.
Dated: April 7, 2011.
Leslie Kux,
Acting Assistant Commissioner for Policy.
[FR Doc. 2011–8944 Filed 4–13–11; 8:45 am]
BILLING CODE 4160–01–P
E:\FR\FM\14APR1.SGM
14APR1
Agencies
[Federal Register Volume 76, Number 72 (Thursday, April 14, 2011)]
[Rules and Regulations]
[Pages 20840-20842]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2011-8944]
=======================================================================
-----------------------------------------------------------------------
DEPARTMENT OF HEALTH AND HUMAN SERVICES
Food and Drug Administration
21 CFR Part 878
[Docket No. FDA-2011-N-0188]
Medical Devices; General and Plastic Surgery Devices;
Classification of the Low Level Laser System for Aesthetic Use
AGENCY: Food and Drug Administration, HHS.
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: The Food and Drug Administration (FDA) is classifying the low
level laser system for aesthetic use into class II (special controls).
The special control(s) that will apply to the device is entitled
``Class II Special Controls Guidance Document: Low Level Laser System
for Aesthetic Use.'' The Agency is classifying the device into class II
(special controls) in order to provide a reasonable assurance of safety
and effectiveness of the device. Elsewhere in this issue of the Federal
Register, FDA is announcing the availability of a guidance document
that will serve as the special control for this device type.
DATES: This rule is effective May 16, 2011. The classification was
effective on August 24, 2010.
FOR FURTHER INFORMATION CONTACT: Richard Felten, Center for Devices and
Radiological Health, Food and Drug Administration, 10903 New Hampshire
Ave., Bldg. 66, Rm. 1436, Silver Spring, MD 20993-0002, 301-796-6392.
SUPPLEMENTARY INFORMATION:
I. What is the background of this rulemaking?
In accordance with section 513(f)(1) of the Federal Food, Drug, and
Cosmetic Act (the FD&C Act) (21 U.S.C. 360c(f)(1)), devices that were
not in commercial distribution before May 28, 1976 (the date of
enactment of the Medical Device Amendments of 1976), generally referred
to as postamendments devices, are classified automatically by statute
into class III without any FDA rulemaking process. These devices remain
in class III and require premarket approval, unless and until the
device is classified or reclassified into class I or II, or FDA issues
an order finding the device to be substantially equivalent, in
accordance with section 513(i) of the FD&C Act, to a predicate device
that does not require premarket approval. The Agency determines whether
new devices are substantially equivalent to predicate devices by means
of premarket notification procedures in section 510(k) of the FD&C Act
(21 U.S.C. 360(k)) and 21 CFR part 807 of the regulations.
Section 513(f)(2) of the FD&C Act provides that any person who
submits a premarket notification under section 510(k) of the FD&C Act
for a device that has not previously been classified may, within 30
days after receiving an order classifying the device into class III
under section 513(f)(1) of the FD&C Act, request FDA to classify the
device under the criteria set forth in section 513(a)(1) of the FD&C
Act. FDA will, within 60 days of receiving this request, classify the
device by written order. This classification will be the initial
classification of the device. Within 30 days after the issuance of an
order classifying the device, FDA must publish a notice in the Federal
Register announcing this classification.
In accordance with section 513(f)(1) of the FD&C Act, FDA issued an
order on
[[Page 20841]]
December 22, 2008, classifying the Erchonia Low Level Laser System for
Aesthetic Use into class III because it was not substantially
equivalent to a device that was introduced or delivered for
introduction into interstate commerce for commercial distribution
before May 28, 1976, or a device which was subsequently reclassified
into class I or class II. On January 5, 2009, Erchonia, Inc., submitted
a petition requesting classification of the Erchonia Low Level Laser
System for Aesthetic Use under section 513(f)(2) of the FD&C Act. The
manufacturer recommended that the device be classified into class II.
(Ref. 1)
In accordance with section 513(f)(2) of the FD&C Act, FDA reviewed
the petition in order to classify the device under the criteria for
classification set forth in section 513(a)(1) of the FD&C Act. FDA
classifies devices into class II if general controls by themselves are
insufficient to provide reasonable assurance of safety and
effectiveness, but there is sufficient information to establish special
controls to provide reasonable assurance of the safety and
effectiveness of the device for its intended use. After review of the
information submitted in the petition, FDA determined that the device
can be classified into class II with the establishment of special
controls. FDA believes these special controls will provide reasonable
assurance of the safety and effectiveness of the device.
The device is assigned the generic name Low Level Laser System for
Aesthetic Use, and it is identified as a device using low level laser
energy for the disruption of adipocyte cells within the fat layer for
the release of fat and lipids from these cells for noninvasive
aesthetic use.
FDA has identified the following risks to health associated
specifically with this type of device and the recommended measures to
mitigate these risks.
Ocular injury is a recognized hazard from laser optical
systems because of the unique physical characteristics of laser light;
that is, this optical radiation is easily transmitted into the eye as a
very bright, intense light beam that may produce lesions on the retina.
This hazard is addressed by device labeling, which includes
recommendations for not looking directly at the laser beam and the
wearing of appropriate laser safety eyewear by both the user and
patient. The labeling also includes information defining the size of
the area within which this optical hazard exists.
Electrical shock is addressed by recommended testing of
the device according to recognized U.S. and international standards
specifically designed to determine and measure potential electrical
safety. Again, the recommended device labeling also includes specific
warnings for the user in terms of device placement, appropriate
electrical wiring needs, reminders to periodically check device wiring
and accessories for damage, and avoidance of use of the device in
environments where electrical shock is possible.
Unintended cell damage is a potential risk from use of low
level lasers if improper or incorrect energy is used to initiate the
process of causing lipid and fat leakage from the target adipocyte
cells. The intended effect on the adipocyte cells is the creation of
pores that results in the lipid or fat leaving these specialized cells;
however, if the laser parameters are not correct, no effect may occur
in terms of adipocyte change or other non-adipocyte cells may be
affected, resulting in alteration of other cellular membranes or
transport systems that could result in unintended cell death.
Use error represents those risks to the patient that can
occur from improper use of the device. In order to address this
potential risk, we recommend the manufacturer provide a detailed
operator manual, which contains information on possible risks and
hazards and how these should be avoided and clear recommended safe
treatment procedures that include information on device settings for
treatment, clear information on how the device is to be used during
treatment, and recommended posttreatment care.
FDA believes that the class II special controls guidance document
will aid in mitigating the potential risks to health as described in
table 1 of this document.
Table 1--Risks to Health and Mitigation Measures
------------------------------------------------------------------------
Identified risk Recommended mitigation measures
------------------------------------------------------------------------
Ocular Injury.......................... Section 6. Bench Testing.
Section 7. Software Validation.
Section 8. Clinical Testing.
Section 12. Labeling.
Electrical Shock....................... Section 11. Electrical and
Mechanical Safety Performance
Testing (IEC 60601-1).
Section 12. Labeling.
Unintended Cell Damage................. Section 6. Bench Testing.
Section 7. Software Validation.
Section 8. Clinical Testing.
Section 9. Biocompatibility.
Section 10. Electromagnetic
Compatibility (IEC 60601-1-2).
Section 12. Labeling.
Use Error.............................. Section 12. Labeling.
------------------------------------------------------------------------
FDA believes that the special controls guidance, ``Low Level Laser
System for Aesthetic Use,'' in addition to general controls, address
the risks to health and provide reasonable assurance of the safety and
effectiveness of the device. Therefore, on August 24, 2010, FDA issued
an order to the petitioner classifying the device into class II. FDA is
codifying the classification of the device by adding Sec. 878.5400.
Following the effective date of this final classification rule, any
firm submitting a 510(k) premarket notification for low level laser
system for aesthetic use will need to address the issues covered in the
special controls guidance. However, the firm need only show that its
device meets the recommendations of the guidance or in some other way
provides equivalent assurance of safety and effectiveness.
Section 510(m) of the FD&C Act provides that FDA may exempt a class
II device from the premarket notification requirements under section
510(k) of the FD&C Act, if FDA determines that premarket notification
is not necessary to provide reasonable assurance of the
[[Page 20842]]
safety and effectiveness of the device. For this type of device, FDA
has determined that premarket notification is necessary to provide
reasonable assurance of the safety and effectiveness of the device.
Therefore, this device type is not exempt from premarket notification
requirements. Persons who intend to market this type of device must
submit to FDA a premarket notification, prior to marketing the device,
which contains information about the low level laser system for
aesthetic use they intend to market.
II. What is the environmental impact of this rule?
The Agency has determined under 21 CFR 25.34(b) that this action is
of a type that does not individually or cumulatively have a significant
effect on the human environment. Therefore, neither an environmental
assessment nor an environmental impact statement is required.
III. What is the analysis of impacts of this rule?
FDA has examined the impacts of the final rule under Executive
Order 12866 and the Regulatory Flexibility Act (5 U.S.C. 601-612), and
the Unfunded Mandates Reform Act of 1995 (Pub. L. 104-4). Executive
Order 12866 directs Agencies to assess all costs and benefits of
available regulatory alternatives and, when regulation is necessary, to
select regulatory approaches that maximize net benefits (including
potential economic, environmental, public health and safety, and other
advantages; distributive impacts; and equity). The Agency believes that
this final rule is not a significant regulatory action as defined by
the Executive order and so it is not subject to review under the
Executive order.
The Regulatory Flexibility Act requires Agencies to analyze
regulatory options that would minimize any significant impact of a rule
on small entities. Because reclassification of this device from class
III to class II will relieve manufacturers of the device of the cost of
complying with the premarket approval requirements of section 515 of
the FD&C Act (21 U.S.C. 360e), and may permit small potential
competitors to enter the marketplace by lowering their costs, the
Agency certifies that the final rule will not have a significant
economic impact on a substantial number of small entities.
Section 202(a) of the Unfunded Mandates Reform Act of 1995 requires
that Agencies prepare a written statement, which includes an assessment
of anticipated costs and benefits, before proposing ``any rule that
includes any Federal mandate that may result in the expenditure by
State, local, and tribal governments, in the aggregate, or by the
private sector, of $100,000,000 or more (adjusted annually for
inflation) in any one year.'' The current threshold after adjustment
for inflation is $135 million, using the most current (2009) Implicit
Price Deflator for the Gross Domestic Product. FDA does not expect this
final rule to result in any 1-year expenditure that would meet or
exceed this amount.
IV. Does this rule have federalism implications?
FDA has analyzed this final rule in accordance with the principles
set forth in Executive Order 13132. Section 4(a) of the Executive order
requires Agencies to ``construe * * * a Federal statute to preempt
State law only where the statute contains an express preemption
provision or there is some other clear evidence that the Congress
intended preemption of State law, or where the exercise of State
authority conflicts with the exercise of Federal authority under the
Federal statute.'' Federal law includes an express preemption provision
that preempts certain state requirements ``different from or in
addition to'' certain Federal requirements applicable to devices. (See
section 521 of the FD&C Act (21 U.S.C. 360k); See Medtronic, Inc., v.
Lohr, 518 U.S. 470 (1996); and Riegel v. Medtronic, Inc., 128 S. Ct.
999 (2008)). The special controls established by this final rule
creates ``requirements'' for specific medical devices under 21 U.S.C.
360k, even though product sponsors have some flexibility in how they
meet those requirements. (See Papike v. Tambrands, Inc., 107 F.3d 737,
740-42 (9th Cir. 1997)).
V. How does this rule comply with the Paperwork Reduction Act of 1995?
FDA concludes that this final rule contains no new collections of
information. Therefore, clearance by the Office of Management and
Budget (OMB) under the Paperwork Reduction Act of 1995 (PRA) (44 U.S.C.
3501-3520) is not required. This final rule establishes as special
controls a guidance document that refers to previously approved
collections of information found in other FDA regulations. These
collections of information are subject to review by OMB under the PRA.
Elsewhere in this issue of the Federal Register, FDA is issuing a
notice announcing the availability of the guidance document entitled
``Class II Special Controls Guidance Document: Low Level Laser System
for Aesthetic Use'' that will serve as the special control for this
device. This notice contains an analysis of the paperwork burden for
the guidance document.
VI. References
The following references have been placed on display in the
Division of Dockets Management (HFA-305), Food and Drug Administration,
5630 Fishers Lane, rm. 1061, Rockville, MD 20852, and may be seen by
interested persons between 9 a.m. and 4 p.m., Monday through Friday.
1. Petition from Erchonia, Inc., January 5, 2009.
List of Subjects in 21 CFR Part 878
Medical devices.
Therefore, under the Federal Food, Drug, and Cosmetic Act and under
authority delegated to the Commissioner of Food and Drugs, 21 CFR part
878 is amended as follows:
PART 878--GENERAL AND PLASTIC SURGERY DEVICES
0
1. The authority citation for 21 CFR part 878 continues to read as
follows:
Authority: 21 U.S.C. 351, 360, 360c, 360e, 360j, 360l, 371.
0
2. Section 878.5400 is added to subpart F to read as follows:
Sec. 878.5400 Low Level Laser System for Aesthetic Use
(a) Identification. A Low Level Laser System for Aesthetic Use is a
device using low level laser energy for the disruption of adipocyte
cells within the fat layer for the release of fat and lipids from these
cells for noninvasive aesthetic use.
(b) Classification. Class II (special controls). The special
control for this device is the FDA guidance document entitled
``Guidance for Industry and Food and Drug Administration Staff; Class
II Special Controls Guidance Document: Low Level Laser System for
Aesthetic Use.'' See Sec. 878.1(e) for the availability of this
guidance document.
Dated: April 7, 2011.
Leslie Kux,
Acting Assistant Commissioner for Policy.
[FR Doc. 2011-8944 Filed 4-13-11; 8:45 am]
BILLING CODE 4160-01-P