Airworthiness Directives; PIAGGIO AERO INDUSTRIES S.p.A Model PIAGGIO P-180 Airplanes, 63058-63060 [2010-25284]

Download as PDF 63058 Federal Register / Vol. 75, No. 198 / Thursday, October 14, 2010 / Rules and Regulations number 001 thru 0767: Modification of the valve accomplished before the effective date of this AD in accordance with Bombardier Service Bulletin 601R–32–090, Revision B, dated December 12, 2006; and Bombardier Service Bulletin Revision C, dated March 3, 2009; are considered acceptable for compliance with the requirements of this AD for that valve. FAA AD Differences Note 1: This AD differs from the MCAI and/or service information as follows: No differences. Other FAA AD Provisions (g) The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, New York Aircraft Certification Office (ACO), ANE–170, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Program Manager, Continuing Operational Safety, FAA, New York ACO, 1600 Stewart Avenue, Suite 410, Westbury, New York 11590; telephone (516) 228–7300; fax (516) 794–5531. Before using any approved AMOC on any airplane to which the AMOC applies, notify your principal maintenance inspector (PMI) or principal avionics inspector (PAI), as appropriate, or lacking a principal inspector, your local Flight Standards District Office. The AMOC approval letter must specifically reference this AD. (2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service. (3) Reporting Requirements: For any reporting requirement in this AD, under the provisions of the Paperwork Reduction Act (44 U.S.C. 3501 et seq.), the Office of Management and Budget (OMB) has approved the information collection requirements and has assigned OMB Control Number 2120–0056. emcdonald on DSK2BSOYB1PROD with RULES Related Information (h) Refer to MCAI Canadian Airworthiness Directive CF–2009–19, dated April 29, 2009; and Bombardier Service Bulletin 601R–32– 104, dated March 3, 2009; for related information. Material Incorporated by Reference (i) You must use Bombardier Service Bulletin 601R–32–104, dated March 3, 2009, to do the actions required by this AD, unless the AD specifies otherwise. (1) The Director of the Federal Register approved the incorporation by reference of the service information under 5 U.S.C. 552(a) and 1 CFR part 51. (2) For service information identified in ˆ this AD, contact Bombardier, Inc., 400 Cote´ Vertu Road West, Dorval, Quebec H4S 1Y9, Canada; telephone 514–855–5000; fax 514– 855–7401; e-mail thd.crj@aero.bombardier.com; Internet https:// www.bombardier.com. VerDate Mar<15>2010 16:06 Oct 13, 2010 Jkt 223001 (3) You may review copies of the service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington. For information on the availability of this material at the FAA, call 425–227–1221. (4) You may also review copies of the service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202–741–6030, or go to: https://www.archives.gov/federal_register/ code_of_federal_regulations/ ibr_locations.html. Issued in Renton, Washington, on September 29, 2010. Ali Bahrami, Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. 2010–25458 Filed 10–13–10; 8:45 am] BILLING CODE 4910–13–P DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2010–0734 Directorate Identifier 2010–CE–036–AD; Amendment 39–16474; AD 2010–21–14] RIN 2120–AA64 Airworthiness Directives; PIAGGIO AERO INDUSTRIES S.p.A Model PIAGGIO P–180 Airplanes Federal Aviation Administration (FAA), Department of Transportation (DOT). ACTION: Final rule. AGENCY: We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: SUMMARY: Due to a manufacturing error, some rivets, required by drawings, were not installed in the joints between two ceiling beams and the rear pressurized bulkhead. If left uncorrected, long term fatigue stress could locally weaken the structure, compromising the fuselage structural integrity. We are issuing this AD to require actions to correct the unsafe condition on these products. DATES: This AD becomes effective November 18, 2010. On November 18, 2010, the Director of the Federal Register approved the incorporation by reference of certain publications listed in this AD. PO 00000 Frm 00020 Fmt 4700 Sfmt 4700 You may examine the AD docket on the Internet at https:// www.regulations.gov or in person at Document Management Facility, U.S. Department of Transportation, Docket Operations, M–30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue, SE., Washington, DC 20590. FOR FURTHER INFORMATION CONTACT: Sarjapur Nagarajan, Aerospace Engineer, FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 329– 4145; fax: (816) 329–4090. SUPPLEMENTARY INFORMATION: ADDRESSES: Discussion We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR part 39 to include an AD that would apply to the specified products. That NPRM was published in the Federal Register on July 23, 2010 (75 FR 43105). That NPRM proposed to correct an unsafe condition for the specified products. The MCAI states: Due to a manufacturing error, some rivets, required by drawings, were not installed in the joints between two ceiling beams and the rear pressurized bulkhead. If left uncorrected, long term fatigue stress could locally weaken the structure, compromising the fuselage structural integrity. This AD requires the accomplishment of Piaggio Aero Industries (PAI) Service Bulletin (SB) 80–0268 original issue, which contains instructions to rework the affected area, thus restoring the fuselage design strength as well as the fatigue specifications of the structure. You may obtain further information by examining the MCAI in the AD docket. Comments We gave the public the opportunity to participate in developing this AD. We received no comments on the NPRM or on the determination of the cost to the public. Conclusion We reviewed the available data and determined that air safety and the public interest require adopting the AD as proposed. Differences Between This AD and the MCAI or Service Information We have reviewed the MCAI and related service information and, in general, agree with their substance. But we might have found it necessary to use different words from those in the MCAI to ensure the AD is clear for U.S. operators and is enforceable. In making these changes, we do not intend to differ substantively from the information E:\FR\FM\14OCR1.SGM 14OCR1 Federal Register / Vol. 75, No. 198 / Thursday, October 14, 2010 / Rules and Regulations provided in the MCAI and related service information. We might also have required different actions in this AD from those in the MCAI in order to follow FAA policies. Any such differences are highlighted in a NOTE within the AD. Costs of Compliance We estimate that this AD will affect 6 products of U.S. registry. We also estimate that it will take about 30 workhours per product to comply with the basic requirements of this AD. The average labor rate is $85 per work-hour. Required parts will cost about $100 per product. Based on these figures, we estimate the cost of this AD to the U.S. operators to be $15,900 or $2,650 per product. Authority for This Rulemaking Title 49 of the United States Code specifies the FAA’s authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. ‘‘Subtitle VII: Aviation Programs,’’ describes in more detail the scope of the Agency’s authority. We are issuing this rulemaking under the authority described in ‘‘Subtitle VII, Part A, Subpart III, Section 44701: General requirements.’’ Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. emcdonald on DSK2BSOYB1PROD with RULES Regulatory Findings We determined that this AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government. For the reasons discussed above, I certify this AD: (1) Is not a ‘‘significant regulatory action’’ under Executive Order 12866; (2) Is not a ‘‘significant rule’’ under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and (3) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. VerDate Mar<15>2010 16:06 Oct 13, 2010 Jkt 223001 We prepared a regulatory evaluation of the estimated costs to comply with this AD and placed it in the AD Docket. Examining the AD Docket You may examine the AD docket on the Internet at https:// www.regulations.gov; or in person at the Docket Management Facility between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains the NPRM, the regulatory evaluation, any comments received, and other information. The street address for the Docket Office (telephone (800) 647–5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt. List of Subjects in 14 CFR Part 39 Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety. Adoption of the Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows: ■ PART 39—AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows: ■ Authority: 49 U.S.C. 106(g), 40113, 44701. § 39.13 [Amended] 2. The FAA amends § 39.13 by adding the following new AD: ■ 2010–21–14 PIAGGIO AERO INDUSTRIES S.p.A: Amendment 39–16474; Docket No. FAA–2010–0734; Directorate Identifier 2010–CE–036–AD. Effective Date (a) This airworthiness directive (AD) becomes effective November 18, 2010. Affected ADs (b) None. Applicability (c) This AD applies to PIAGGIO AERO INDUSTRIES S.p.A Model PIAGGIO P–180 airplanes, serial numbers 1166 through 1175, certificated in any category. Subject (d) Air Transport Association of America (ATA) Code 53: Fuselage. Reason (e) The mandatory continuing airworthiness information (MCAI) states: Due to a manufacturing error, some rivets, required by drawings, were not installed in the joints between two ceiling beams and the rear pressurized bulkhead. If left uncorrected, long term fatigue stress could locally weaken the structure, PO 00000 Frm 00021 Fmt 4700 Sfmt 4700 63059 compromising the fuselage structural integrity. This AD requires the accomplishment of Piaggio Aero Industries (PAI) Service Bulletin (SB) 80–0268 original issue, which contains instructions to rework the affected area, thus restoring the fuselage design strength as well as the fatigue specifications of the structure. Actions and Compliance (f) Unless already done, within 200 hours time-in-service (TIS) after November 18, 2010 (the effective date of this AD), replace the rivets of the joint brackets on the right-hand and left-hand beam with ‘‘Hi-Lok’’ fasteners, following the accomplishment instructions of PIAGGIO AERO INDUSTRIES S.p.A. Service Bulletin (Mandatory) N.: 80–0268, REV. 0, dated December 18, 2008. FAA AD Differences Note: This AD differs from the MCAI and/or service information as follows: No differences. Other FAA AD Provisions (g) The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, Standards Office, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Sarjapur Nagarajan, Aerospace Engineer, FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 329–4145; fax: (816) 329–4090; e-mail: sarjapur.nagarajan@faa.gov. Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO. (2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service. (3) Reporting Requirements: For any reporting requirement in this AD, under the provisions of the Paperwork Reduction Act (44 U.S.C. 3501 et seq.), the Office of Management and Budget (OMB) has approved the information collection requirements and has assigned OMB Control Number 2120–0056. Related Information (h) Refer to MCAI European Aviation Safety Agency (EASA) AD No.: 2010–0126, dated June 23, 2010; and PIAGGIO AERO INDUSTRIES S.p.A. Service Bulletin (Mandatory) N.: 80–0268, REV. 0, dated December 18, 2008, for related information. Material Incorporated by Reference (i) You must use PIAGGIO AERO INDUSTRIES S.p.A. Service Bulletin (Mandatory) N.: 80–0268, REV. 0, dated December 18, 2008, to do the actions E:\FR\FM\14OCR1.SGM 14OCR1 63060 Federal Register / Vol. 75, No. 198 / Thursday, October 14, 2010 / Rules and Regulations required by this AD, unless the AD specifies otherwise. (1) The Director of the Federal Register approved the incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51. (2) For service information identified in this AD, contact Piaggio Aero Industries S.p.a., Via Cibrario, 4–16154 Genoa, Italy; phone: +39 010 6481 353; fax: +39 010 6481 881; e-mail: airworthiness@piaggioaero.it; Internet: https://www.piaggioaero.com. (3) You may review copies of the service information incorporated by reference for this AD at the FAA, Central Region, Office of the Regional Counsel, 901 Locust, Kansas City, Missouri 64106. For information on the availability of this material at the Central Region, call (816) 329–3768. (4) You may also review copies of the service information incorporated by reference for this AD at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call (202) 741–6030, or go to: https://www.archives.gov/federal_register/ code_of_federal_regulations/ ibr_locations.html. Issued in Kansas City, Missouri, on September 30, 2010. John R. Colomy, Acting Manager, Small Airplane Directorate, Aircraft Certification Service. [FR Doc. 2010–25284 Filed 10–13–10; 8:45 am] BILLING CODE 4910–13–P DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2010–0737; Directorate Identifier 2010–CE–037–AD; Amendment 39–16468; AD 2010–21–08] Airworthiness Directives; PIAGGIO AERO INDUSTRIES S.p.A. Model PIAGGIO P–180 Airplanes Federal Aviation Administration (FAA), Department of Transportation (DOT). ACTION: Final rule. AGENCY: We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: emcdonald on DSK2BSOYB1PROD with RULES SUMMARY: Some cases of failure of engine oil dipsticks, installed on Pratt & Whitney Canada (P&WC) PT6A66 and PT6A66B engines, were detected on P.180 aeroplanes; such failures, due to moisture penetration 16:06 Oct 13, 2010 Jkt 223001 This Correction is issued to amend the AD number heading: It was PAD, it is AD. If left uncorrected, this situation could lead to in-flight engine failure(s). We are issuing this AD to require actions to correct the unsafe condition on these products. DATES: This AD becomes effective November 18, 2010. On November 18, 2010, the Director of the Federal Register approved the incorporation by reference of certain publications listed in this AD. ADDRESSES: You may examine the AD docket on the Internet at https:// www.regulations.gov or in person at Document Management Facility, U.S. Department of Transportation, Docket Operations, M–30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue, SE., Washington, DC 20590. FOR FURTHER INFORMATION CONTACT: Sarjapur Nagarajan, Aerospace Engineer, FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 329– 4145; fax: (816) 329–4090. SUPPLEMENTARY INFORMATION: Comments Discussion We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR part 39 to include an AD that would apply to the specified products. That NPRM was published in the Federal Register on July 23, 2010 (75 FR 43095). That NPRM proposed to correct an unsafe condition for the specified products. The MCAI states: Some cases of failure of engine oil dipsticks, installed on Pratt & Whitney Canada (P&WC) PT6A66 and PT6A66B engines, were detected on P.180 aeroplanes; such failures, due to moisture penetration into the dipstick and subsequent corrosion, can cause incorrect reading of the engine oil low level on the Refuel/Ground Test Panel. RIN 2120–AA64 VerDate Mar<15>2010 into the dipstick and subsequent corrosion, can cause incorrect reading of the engine oil low level on the Refuel/Ground Test Panel. If left uncorrected, this situation could lead to in-flight engine failure(s). This AD requires: (1) Repetitive visual checks of the engine oil levels to prevent an undetected low level condition; (2) Repetitive inspections of the oil dipsticks to detect faulty units; (3) Replacement of faulty oil dipsticks or visual checks of the oil level at reduced not to exceed intervals, until replacement of faulty units. The engine TC Holder is currently developing a modification that will address the unsafe condition identified in this AD; once such modification is developed, approved and available, further mandatory actions might be considered. PO 00000 Frm 00022 Fmt 4700 Sfmt 4700 We gave the public the opportunity to participate in developing this AD. We received no comments on the NPRM or on the determination of the cost to the public. Conclusion We reviewed the available data and determined that air safety and the public interest require adopting the AD as proposed. Differences Between This AD and the MCAI or Service Information We have reviewed the MCAI and related service information and, in general, agree with their substance. But we might have found it necessary to use different words from those in the MCAI to ensure the AD is clear for U.S. operators and is enforceable. In making these changes, we do not intend to differ substantively from the information provided in the MCAI and related service information. We might also have required different actions in this AD from those in the MCAI in order to follow FAA policies. Any such differences are highlighted in a NOTE within the AD. Costs of Compliance We estimate that this AD will affect 99 products of U.S. registry. We also estimate that it will take about 2.5 workhours per product to comply with the basic requirements of this AD. The average labor rate is $85 per work-hour. Based on these figures, we estimate the cost of this AD to the U.S. operators to be $21,038 or $212.50 per product. In addition, we estimate that any necessary follow-on actions would take about 1 work-hour and require parts costing $9,000, for a cost of $9,085 per product. We have no way of determining the number of products that may need these actions. Authority for This Rulemaking Title 49 of the United States Code specifies the FAA’s authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. ‘‘Subtitle VII: Aviation Programs,’’ describes in more detail the scope of the Agency’s authority. We are issuing this rulemaking under the authority described in ‘‘Subtitle VII, Part A, Subpart III, Section 44701: General requirements.’’ Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in E:\FR\FM\14OCR1.SGM 14OCR1

Agencies

[Federal Register Volume 75, Number 198 (Thursday, October 14, 2010)]
[Rules and Regulations]
[Pages 63058-63060]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2010-25284]

-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2010-0734 Directorate Identifier 2010-CE-036-AD;
Amendment 39-16474; AD 2010-21-14]
RIN 2120-AA64

Airworthiness Directives; PIAGGIO AERO INDUSTRIES S.p.A Model
PIAGGIO P-180 Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of
Transportation (DOT).

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: We are adopting a new airworthiness directive (AD) for the
products listed above. This AD results from mandatory continuing
airworthiness information (MCAI) issued by an aviation authority of
another country to identify and correct an unsafe condition on an
aviation product. The MCAI describes the unsafe condition as:

We are issuing this AD to require actions to correct the unsafe
condition on these products.

DATES: This AD becomes effective November 18, 2010.
On November 18, 2010, the Director of the Federal Register approved
the incorporation by reference of certain publications listed in this
AD.

ADDRESSES: You may examine the AD docket on the Internet at https://www.regulations.gov or in person at Document Management Facility, U.S.
Department of Transportation, Docket Operations, M-30, West Building
Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC
20590.

FOR FURTHER INFORMATION CONTACT: Sarjapur Nagarajan, Aerospace
Engineer, FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas
City, Missouri 64106; telephone: (816) 329-4145; fax: (816) 329-4090.

SUPPLEMENTARY INFORMATION:

Discussion

We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR
part 39 to include an AD that would apply to the specified products.
That NPRM was published in the Federal Register on July 23, 2010 (75 FR
43105). That NPRM proposed to correct an unsafe condition for the
specified products. The MCAI states:

Due to a manufacturing error, some rivets, required by drawings,
were not installed in the joints between two ceiling beams and the
rear pressurized bulkhead.
If left uncorrected, long term fatigue stress could locally
weaken the structure, compromising the fuselage structural
integrity.
This AD requires the accomplishment of Piaggio Aero Industries
(PAI) Service Bulletin (SB) 80-0268 original issue, which contains
instructions to rework the affected area, thus restoring the
fuselage design strength as well as the fatigue specifications of
the structure.

You may obtain further information by examining the MCAI in the AD
docket.

Comments

We gave the public the opportunity to participate in developing
this AD. We received no comments on the NPRM or on the determination of
the cost to the public.

Conclusion

We reviewed the available data and determined that air safety and
the public interest require adopting the AD as proposed.

Differences Between This AD and the MCAI or Service Information

We have reviewed the MCAI and related service information and, in
general, agree with their substance. But we might have found it
necessary to use different words from those in the MCAI to ensure the
AD is clear for U.S. operators and is enforceable. In making these
changes, we do not intend to differ substantively from the information

[[Page 63059]]

provided in the MCAI and related service information.
We might also have required different actions in this AD from those
in the MCAI in order to follow FAA policies. Any such differences are
highlighted in a NOTE within the AD.

Costs of Compliance

We estimate that this AD will affect 6 products of U.S. registry.
We also estimate that it will take about 30 work-hours per product to
comply with the basic requirements of this AD. The average labor rate
is $85 per work-hour. Required parts will cost about $100 per product.
Based on these figures, we estimate the cost of this AD to the U.S.
operators to be $15,900 or $2,650 per product.

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. ``Subtitle VII: Aviation
Programs,'' describes in more detail the scope of the Agency's
authority.
We are issuing this rulemaking under the authority described in
``Subtitle VII, Part A, Subpart III, Section 44701: General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.

Regulatory Findings

We determined that this AD will not have federalism implications
under Executive Order 13132. This AD will not have a substantial direct
effect on the States, on the relationship between the national
government and the States, or on the distribution of power and
responsibilities among the various levels of government.
For the reasons discussed above, I certify this AD:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866;
(2) Is not a ``significant rule'' under DOT Regulatory Policies and
Procedures (44 FR 11034, February 26, 1979); and
(3) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to
comply with this AD and placed it in the AD Docket.

Examining the AD Docket

You may examine the AD docket on the Internet at https://www.regulations.gov; or in person at the Docket Management Facility
between 9 a.m. and 5 p.m., Monday through Friday, except Federal
holidays. The AD docket contains the NPRM, the regulatory evaluation,
any comments received, and other information. The street address for
the Docket Office (telephone (800) 647-5527) is in the ADDRESSES
section. Comments will be available in the AD docket shortly after
receipt.

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.

Adoption of the Amendment

0
Accordingly, under the authority delegated to me by the Administrator,
the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

Sec. 39.13 [Amended]

0
2. The FAA amends Sec. 39.13 by adding the following new AD:

2010-21-14 PIAGGIO AERO INDUSTRIES S.p.A: Amendment 39-16474; Docket
No. FAA-2010-0734; Directorate Identifier 2010-CE-036-AD.

Effective Date

(a) This airworthiness directive (AD) becomes effective November
18, 2010.

Affected ADs

(b) None.

Applicability

(c) This AD applies to PIAGGIO AERO INDUSTRIES S.p.A Model
PIAGGIO P-180 airplanes, serial numbers 1166 through 1175,
certificated in any category.

Subject

(d) Air Transport Association of America (ATA) Code 53:
Fuselage.

Reason

(e) The mandatory continuing airworthiness information (MCAI)
states:

Actions and Compliance

(f) Unless already done, within 200 hours time-in-service (TIS)
after November 18, 2010 (the effective date of this AD), replace the
rivets of the joint brackets on the right-hand and left-hand beam
with ``Hi-Lok'' fasteners, following the accomplishment instructions
of PIAGGIO AERO INDUSTRIES S.p.A. Service Bulletin (Mandatory) N.:
80-0268, REV. 0, dated December 18, 2008.

FAA AD Differences

Note: This AD differs from the MCAI and/or service information
as follows: No differences.

Other FAA AD Provisions

(g) The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager,
Standards Office, FAA, has the authority to approve AMOCs for this
AD, if requested using the procedures found in 14 CFR 39.19. Send
information to ATTN: Sarjapur Nagarajan, Aerospace Engineer, FAA,
Small Airplane Directorate, 901 Locust, Room 301, Kansas City,
Missouri 64106; telephone: (816) 329-4145; fax: (816) 329-4090; e-
mail: sarjapur.nagarajan@faa.gov. Before using any approved AMOC on
any airplane to which the AMOC applies, notify your appropriate
principal inspector (PI) in the FAA Flight Standards District Office
(FSDO), or lacking a PI, your local FSDO.
(2) Airworthy Product: For any requirement in this AD to obtain
corrective actions from a manufacturer or other source, use these
actions if they are FAA-approved. Corrective actions are considered
FAA-approved if they are approved by the State of Design Authority
(or their delegated agent). You are required to assure the product
is airworthy before it is returned to service.
(3) Reporting Requirements: For any reporting requirement in
this AD, under the provisions of the Paperwork Reduction Act (44
U.S.C. 3501 et seq.), the Office of Management and Budget (OMB) has
approved the information collection requirements and has assigned
OMB Control Number 2120-0056.

Related Information

(h) Refer to MCAI European Aviation Safety Agency (EASA) AD No.:
2010-0126, dated June 23, 2010; and PIAGGIO AERO INDUSTRIES S.p.A.
Service Bulletin (Mandatory) N.: 80-0268, REV. 0, dated December 18,
2008, for related information.

Material Incorporated by Reference

(i) You must use PIAGGIO AERO INDUSTRIES S.p.A. Service Bulletin
(Mandatory) N.: 80-0268, REV. 0, dated December 18, 2008, to do the
actions

[[Page 63060]]

required by this AD, unless the AD specifies otherwise.
(1) The Director of the Federal Register approved the
incorporation by reference of this service information under 5
U.S.C. 552(a) and 1 CFR part 51.
(2) For service information identified in this AD, contact
Piaggio Aero Industries S.p.a., Via Cibrario, 4-16154 Genoa, Italy;
phone: +39 010 6481 353; fax: +39 010 6481 881; e-mail:
airworthiness@piaggioaero.it; Internet: https://www.piaggioaero.com.
(3) You may review copies of the service information
incorporated by reference for this AD at the FAA, Central Region,
Office of the Regional Counsel, 901 Locust, Kansas City, Missouri
64106. For information on the availability of this material at the
Central Region, call (816) 329-3768.
(4) You may also review copies of the service information
incorporated by reference for this AD at the National Archives and
Records Administration (NARA). For information on the availability
of this material at NARA, call (202) 741-6030, or go to: https://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.

Issued in Kansas City, Missouri, on September 30, 2010.
John R. Colomy,
Acting Manager, Small Airplane Directorate, Aircraft Certification
Service.
[FR Doc. 2010-25284 Filed 10-13-10; 8:45 am]
BILLING CODE 4910-13-P

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.