Antimicrobial Pesticide Products; Registration Applications, 30829-30830 [2010-13183]

Download as PDF sroberts on DSKD5P82C1PROD with NOTICES Federal Register / Vol. 75, No. 105 / Wednesday, June 2, 2010 / Notices WWTPs by adding a new MBR treatment process. The membrane filtration cassette is an integral component of the MBR treatment process because it separates the treated wastewater from the mixed liquor which comes from the biological reactors, before the treated wastewater is disinfected and discharged. After an engineering analysis of alternate treatment processes, the CVPSD determined MBR to be the most environmentally sound and cost effective solution. The MBR is an advanced waste water treatment process which is designed to meet the high quality effluent requirements of the waste load allocation under the NPDES permit. In addition, in anticipation of procuring the MBR system, the CVPSD has already incorporated specific technical design requirements for installation of membrane filter cassettes with the MBR treatment process at their WWTPs, including specific tankage footprint, geometry and configuration. To require CVPSD to redesign its project would cause an unacceptable delay to the initiation of construction. The CVPSD has provided information to the EPA demonstrating that there are no membrane filtration cassettes manufactured in the United States in sufficient and reasonable quantity and of a satisfactory quality to meet the required technical specification. Four companies were considered for the membrane filtration cassettes, none based in the United States. The CVPSD has performed market research but was unsuccessful in its effort to locate any domestic manufacturers of membrane filtration cassettes for WWTPs. The April 28, 2009 EPA HQ Memorandum, Implementation of Buy American provisions of Public Law 111–5, the ‘‘American Recovery and Reinvestment Act of 2009’’, defines reasonably available quantity as ‘‘the quantity of iron, steel, or relevant manufactured good is available or will be available at the time needed and place needed, and in the proper form or specification as specified in the project plans and design.’’ The CVPSD has incorporated specific technical design requirements for installation of membrane filtration cassettes at its WWTPs. The purpose of the ARRA is to stimulate economic recovery in part by funding current infrastructure construction, not to delay projects that are ‘‘shovel ready’’ by requiring utilities, such as the CVPSD, to revise their standards and specifications, institute a new bidding process, and potentially choose a more costly, less efficient project. The imposition of ARRA Buy VerDate Mar<15>2010 19:46 Jun 01, 2010 Jkt 220001 American requirements on such projects otherwise eligible for State Revolving Fund assistance would result in unreasonable delay and thus displace the ‘‘shovel ready’’ status for this project. To further delay construction is in direct conflict with a fundamental economic purpose of the ARRA, which is to create or retain jobs. Based on additional research conducted by EPA’s Office of Infrastructure and Assistance (OIA) in Region 3, and to the best of the Region’s knowledge at the time of review, there do not appear to be other membrane filtration cassettes manufactured domestically that would meet the CVPSD’s technical specification. EPA’s national contractor prepared a technical assessment report dated January 9, 2010 based on the waiver request submitted. This report included a detailed review intended to enable EPA to determine if any company could be considered to substantially transform these cassettes in the United States. However, sufficient information was not available or made available to establish either performance characteristics for any potential alternative product, or the substantial transformation of any such product in the United States. Accordingly, the report determined that the waiver request submittal was complete, that adequate technical information was provided, and that there were no significant weaknesses in the justification provided. The report confirmed the waiver applicant’s claim that there are no American-made membrane filtration cassettes for use in MBRs in WWTPs. The OIA has reviewed this waiver request and to the best of our knowledge at the time of review has determined that the supporting documentation provided by the CVPSD is sufficient to meet the criteria listed under Section 1605(b) and in the April 28, 2009, ‘‘Implementation of Buy American provisions of Public Law 111–5, the ‘American Recovery and Reinvestment Act of 2009’ Memorandum:’’ Iron, steel, and the manufactured goods are not produced in the United States in sufficient and reasonably available quantities and of a satisfactory quality. The basis for this project waiver is the authorization provided in Section 1605(b)(2). Due to the lack of production of this product in the United States in sufficient and reasonably available quantities and of a satisfactory quality in order to meet the CVPSD’s technical specifications, a waiver from the Buy American requirement is justified. The March 31, 2009 Delegation of Authority Memorandum provided Regional Administrators with the PO 00000 Frm 00060 Fmt 4703 Sfmt 4703 30829 authority to issue exceptions to Section 1605 of ARRA within the geographic boundaries of their respective regions and with respect to requests by individual grant recipients. Having established both a proper basis to specify the particular good required for this project, and that this manufactured good was not available from a producer in the United States, the Canaan Valley Public Service District is hereby granted a waiver from the Buy American requirements of Section 1605(a) of Public Law 111–5 for the purchase of four membrane filtration cassettes using ARRA funds as specified in the CVPSD’s request of December 16, 2009. This supplementary information constitutes the detailed written justification required by Section 1605(c) for waivers ‘‘based on a finding under subsection (b).’’ Authority: Public Law 111–5, section 1605. Dated: May 17, 2010. W. C. Early, Acting Regional Administrator, Region III. [FR Doc. 2010–13225 Filed 6–1–10; 8:45 am] BILLING CODE 6560–50–P ENVIRONMENTAL PROTECTION AGENCY [EPA–HQ–OPP–2010–0325; FRL–8824–2] Antimicrobial Pesticide Products; Registration Applications AGENCY: Environmental Protection Agency (EPA). ACTION: Notice. SUMMARY: This notice announces receipt of an application to register new antimicrobial pesticide products containing new active ingredients, pursuant to the provisions of section 3(c) of the Federal Insecticide, Fungicide, and Rodenticide Act (FIFRA), as amended. EPA is publishing this Notice of such applications, pursuant to section 3(c)(4) of FIFRA. DATES: Comments must be received on or before July 2, 2010. ADDRESSES: Submit your comments, identified by docket identification (ID) number EPA–HQ– OPP–2010–0325, by one of the following methods: • Federal eRulemaking Portal: https:// www.regulations.gov. Follow the on-line instructions for submitting comments. • Mail: Office of Pesticide Programs (OPP) Regulatory Public Docket (7502P), Environmental Protection Agency, 1200 Pennsylvania Ave., NW., Washington, DC 20460–0001. • Delivery: OPP Regulatory Public Docket (7502P), Environmental E:\FR\FM\02JNN1.SGM 02JNN1 sroberts on DSKD5P82C1PROD with NOTICES 30830 Federal Register / Vol. 75, No. 105 / Wednesday, June 2, 2010 / Notices Protection Agency, Rm. S–4400, One Potomac Yard (South Bldg.), 2777 S. Crystal Dr., Arlington, VA. Deliveries are only accepted during the Docket Facility’s normal hours of operation (8:30 a.m. to 4 p.m., Monday through Friday, excluding legal holidays). Special arrangements should be made for deliveries of boxed information. The Docket Facility telephone number is (703) 305–5805. Instructions: Direct your comments to docket ID number EPA–HQ–OPP–2010– 0325. EPA’s policy is that all comments received will be included in the docket without change and may be made available on-line at https:// www.regulations.gov, including any personal information provided, unless the comment includes information claimed to be Confidential Business Information (CBI) or other information whose disclosure is restricted by statute. Do not submit information that you consider to be CBI or otherwise protected through regulations.gov or email. The regulations.gov website is an ‘‘anonymous access’’ system, which means EPA will not know your identity or contact information unless you provide it in the body of your comment. If you send an e-mail comment directly to EPA without going through regulations.gov, your e-mail address will be automatically captured and included as part of the comment that is placed in the docket and made available on the Internet. If you submit an electronic comment, EPA recommends that you include your name and other contact information in the body of your comment and with any disk or CD-ROM you submit. If EPA cannot read your comment due to technical difficulties and cannot contact you for clarification, EPA may not be able to consider your comment. Electronic files should avoid the use of special characters, any form of encryption, and be free of any defects or viruses. Docket: All documents in the docket are listed in the docket index available at https://www.regulations.gov. Although listed in the index, some information is not publicly available, e.g., CBI or other information whose disclosure is restricted by statute. Certain other material, such as copyrighted material, is not placed on the Internet and will be publicly available only in hard copy form. Publicly available docket materials are available either in the electronic docket at https:// www.regulations.gov, or, if only available in hard copy, at the OPP Regulatory Public Docket in Rm. S– 4400, One Potomac Yard (South Bldg.), 2777 S. Crystal Dr., Arlington, VA. The hours of operation of this Docket VerDate Mar<15>2010 19:08 Jun 01, 2010 Jkt 220001 Facility are from 8:30 a.m. to 4 p.m., Monday through Friday, excluding legal holidays. The Docket Facility telephone number is (703) 305–5805. FOR FURTHER INFORMATION CONTACT: Demson Fuller, Antimicrobials Division (7510P), Office of Pesticide Programs, Environmental Protection Agency, 1200 Pennsylvania Ave., NW., Washington, DC 20460–0001; telephone number: (703) 308–8062; e-mail address: fuller.demson@epa.gov. SUPPLEMENTARY INFORMATION: I. General Information A. Does this Action Apply to Me? You may be potentially affected by this action if you are an agricultural producer, food manufacturer, or pesticide manufacturer. Potentially affected entities may include, but are not limited to: • Pesticide manufacturing (NAICS code 32532). This listing is not intended to be exhaustive, but rather provides a guide for readers regarding entities likely to be affected by this action. Other types of entities not listed in this unit could also be affected. The North American Industrial Classification System (NAICS) codes have been provided to assist you and others in determining whether this action might apply to certain entities. If you have any questions regarding the applicability of this action to a particular entity, consult the person listed under FOR FURTHER INFORMATION CONTACT. B. What Should I Consider as I Prepare My Comments for EPA? 1. Submitting CBI. Do not submit this information to EPA through regulations.gov or e-mail. Clearly mark the part or all of the information that you claim to be CBI. For CBI information in a disk or CD-ROM that you mail to EPA, mark the outside of the disk or CD-ROM as CBI and then identify electronically within the disk or CD-ROM the specific information that is claimed as CBI. In addition to one complete version of the comment that includes information claimed as CBI, a copy of the comment that does not contain the information claimed as CBI must be submitted for inclusion in the public docket. Information so marked will not be disclosed except in accordance with procedures set forth in 40 CFR part 2. 2. Tips for preparing your comments. When submitting comments, remember to: i. Identify the document by docket ID number and other identifying PO 00000 Frm 00061 Fmt 4703 Sfmt 9990 information (subject heading, Federal Register date and page number). ii. Follow directions. The Agency may ask you to respond to specific questions or organize comments by referencing a Code of Federal Regulations (CFR) part or section number. iii. Explain why you agree or disagree; suggest alternatives and substitute language for your requested changes. iv. Describe any assumptions and provide any technical information and/ or data that you used. v. If you estimate potential costs or burdens, explain how you arrived at your estimate in sufficient detail to allow for it to be reproduced. vi. Provide specific examples to illustrate your concerns and suggest alternatives. vii. Explain your views as clearly as possible, avoiding the use of profanity or personal threats. viii. Make sure to submit your comments by the comment period deadline identified. II. Registration Applications EPA has received an application to register a pesticide product containing active ingredients not included in any previously registered pesticide products. Pursuant to the provisions of section 3(c)(4) of FIFRA, EPA is hereby providing notice of receipt and opportunity to comment on this application. Notice of receipt of this application does not imply a decision by the Agency on this application. Registration Number/File Symbol: 85249–R. Docket Number: EPA–HQ– OPP–2010–0325. Company name and address: NanoSilva, LLC, 2811 NE 14th Street, Ocala, FL 34470. Active ingredient: Nanosilver. Proposed Use(s): Antimicrobial and preservative additive used to treat fibers, plastics, polymers, latex products and ceramics. Contact: Demson Fuller, (703) 308–8062; fuller.demson@epa.gov. List of Subjects Environmental protection, Antimicrobial pesticides and pest. Dated: May 21, 2010. Joan Harrigan-Farrelly, Director, Antimicrobials Division, Office of Pesticide Programs. [FR Doc. 2010–13183 Filed 6–1–10; 8:45 am] BILLING CODE 6560–50–S E:\FR\FM\02JNN1.SGM 02JNN1

Agencies

[Federal Register Volume 75, Number 105 (Wednesday, June 2, 2010)]
[Notices]
[Pages 30829-30830]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2010-13183]


-----------------------------------------------------------------------

ENVIRONMENTAL PROTECTION AGENCY

[EPA-HQ-OPP-2010-0325; FRL-8824-2]


Antimicrobial Pesticide Products; Registration Applications

AGENCY: Environmental Protection Agency (EPA).

ACTION: Notice.

-----------------------------------------------------------------------

SUMMARY: This notice announces receipt of an application to register 
new antimicrobial pesticide products containing new active ingredients, 
pursuant to the provisions of section 3(c) of the Federal Insecticide, 
Fungicide, and Rodenticide Act (FIFRA), as amended. EPA is publishing 
this Notice of such applications, pursuant to section 3(c)(4) of FIFRA.

DATES:  Comments must be received on or before July 2, 2010.

ADDRESSES: Submit your comments, identified by docket identification 
(ID) number EPA-HQ- OPP-2010-0325, by one of the following methods:
     Federal eRulemaking Portal: https://www.regulations.gov. 
Follow the on-line instructions for submitting comments.
     Mail: Office of Pesticide Programs (OPP) Regulatory Public 
Docket (7502P), Environmental Protection Agency, 1200 Pennsylvania 
Ave., NW., Washington, DC 20460-0001.
     Delivery: OPP Regulatory Public Docket (7502P), 
Environmental

[[Page 30830]]

Protection Agency, Rm. S-4400, One Potomac Yard (South Bldg.), 2777 S. 
Crystal Dr., Arlington, VA. Deliveries are only accepted during the 
Docket Facility's normal hours of operation (8:30 a.m. to 4 p.m., 
Monday through Friday, excluding legal holidays). Special arrangements 
should be made for deliveries of boxed information. The Docket Facility 
telephone number is (703) 305-5805.
    Instructions: Direct your comments to docket ID number EPA-HQ-OPP-
2010-0325. EPA's policy is that all comments received will be included 
in the docket without change and may be made available on-line at 
https://www.regulations.gov, including any personal information 
provided, unless the comment includes information claimed to be 
Confidential Business Information (CBI) or other information whose 
disclosure is restricted by statute. Do not submit information that you 
consider to be CBI or otherwise protected through regulations.gov or e-
mail. The regulations.gov website is an ``anonymous access'' system, 
which means EPA will not know your identity or contact information 
unless you provide it in the body of your comment. If you send an e-
mail comment directly to EPA without going through regulations.gov, 
your e-mail address will be automatically captured and included as part 
of the comment that is placed in the docket and made available on the 
Internet. If you submit an electronic comment, EPA recommends that you 
include your name and other contact information in the body of your 
comment and with any disk or CD-ROM you submit. If EPA cannot read your 
comment due to technical difficulties and cannot contact you for 
clarification, EPA may not be able to consider your comment. Electronic 
files should avoid the use of special characters, any form of 
encryption, and be free of any defects or viruses.
    Docket: All documents in the docket are listed in the docket index 
available at https://www.regulations.gov. Although listed in the index, 
some information is not publicly available, e.g., CBI or other 
information whose disclosure is restricted by statute. Certain other 
material, such as copyrighted material, is not placed on the Internet 
and will be publicly available only in hard copy form. Publicly 
available docket materials are available either in the electronic 
docket at https://www.regulations.gov, or, if only available in hard 
copy, at the OPP Regulatory Public Docket in Rm. S-4400, One Potomac 
Yard (South Bldg.), 2777 S. Crystal Dr., Arlington, VA. The hours of 
operation of this Docket Facility are from 8:30 a.m. to 4 p.m., Monday 
through Friday, excluding legal holidays. The Docket Facility telephone 
number is (703) 305-5805.

FOR FURTHER INFORMATION CONTACT: Demson Fuller, Antimicrobials Division 
(7510P), Office of Pesticide Programs, Environmental Protection Agency, 
1200 Pennsylvania Ave., NW., Washington, DC 20460-0001; telephone 
number: (703) 308-8062; e-mail address: fuller.demson@epa.gov.

SUPPLEMENTARY INFORMATION:

I. General Information

A. Does this Action Apply to Me?

    You may be potentially affected by this action if you are an 
agricultural producer, food manufacturer, or pesticide manufacturer. 
Potentially affected entities may include, but are not limited to:
     Pesticide manufacturing (NAICS code 32532).
    This listing is not intended to be exhaustive, but rather provides 
a guide for readers regarding entities likely to be affected by this 
action. Other types of entities not listed in this unit could also be 
affected. The North American Industrial Classification System (NAICS) 
codes have been provided to assist you and others in determining 
whether this action might apply to certain entities. If you have any 
questions regarding the applicability of this action to a particular 
entity, consult the person listed under FOR FURTHER INFORMATION 
CONTACT.

B. What Should I Consider as I Prepare My Comments for EPA?

     1. Submitting CBI. Do not submit this information to EPA through 
regulations.gov or e-mail. Clearly mark the part or all of the 
information that you claim to be CBI. For CBI information in a disk or 
CD-ROM that you mail to EPA, mark the outside of the disk or CD-ROM as 
CBI and then identify electronically within the disk or CD-ROM the 
specific information that is claimed as CBI. In addition to one 
complete version of the comment that includes information claimed as 
CBI, a copy of the comment that does not contain the information 
claimed as CBI must be submitted for inclusion in the public docket. 
Information so marked will not be disclosed except in accordance with 
procedures set forth in 40 CFR part 2.
    2. Tips for preparing your comments. When submitting comments, 
remember to:
    i. Identify the document by docket ID number and other identifying 
information (subject heading, Federal Register date and page number).
     ii. Follow directions. The Agency may ask you to respond to 
specific questions or organize comments by referencing a Code of 
Federal Regulations (CFR) part or section number.
    iii. Explain why you agree or disagree; suggest alternatives and 
substitute language for your requested changes.
     iv. Describe any assumptions and provide any technical information 
and/or data that you used.
    v. If you estimate potential costs or burdens, explain how you 
arrived at your estimate in sufficient detail to allow for it to be 
reproduced.
    vi. Provide specific examples to illustrate your concerns and 
suggest alternatives.
    vii. Explain your views as clearly as possible, avoiding the use of 
profanity or personal threats.
     viii. Make sure to submit your comments by the comment period 
deadline identified.

II. Registration Applications

    EPA has received an application to register a pesticide product 
containing active ingredients not included in any previously registered 
pesticide products. Pursuant to the provisions of section 3(c)(4) of 
FIFRA, EPA is hereby providing notice of receipt and opportunity to 
comment on this application. Notice of receipt of this application does 
not imply a decision by the Agency on this application.
    Registration Number/File Symbol: 85249-R. Docket Number: EPA-HQ-
OPP-2010-0325. Company name and address: NanoSilva, LLC, 2811 NE 14th 
Street, Ocala, FL 34470. Active ingredient: Nanosilver. Proposed 
Use(s): Antimicrobial and preservative additive used to treat fibers, 
plastics, polymers, latex products and ceramics. Contact: Demson 
Fuller, (703) 308-8062; fuller.demson@epa.gov.

List of Subjects

    Environmental protection, Antimicrobial pesticides and pest.


    Dated: May 21, 2010.
Joan Harrigan-Farrelly,
Director, Antimicrobials Division, Office of Pesticide Programs.

[FR Doc. 2010-13183 Filed 6-1-10; 8:45 am]
BILLING CODE 6560-50-S
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.