Airworthiness Directives; Eurocopter France (ECF) Model EC120B Helicopters, 22510-22512 [2010-9007]

Download as PDF 22510 Federal Register / Vol. 75, No. 82 / Thursday, April 29, 2010 / Rules and Regulations Actions and Compliance (e) Before the next hoist operation, unless already accomplished, disconnect the ground wire for the hoist squib wiring and test the hoist system to assure that the squib can be electrically fired (MOD 073318) by following the Accomplishment Instructions, Paragraph 2.B.1. through 2.B.4., of Eurocopter Alert Service Bulletin (ASB) No. 25.00.95, for the AS350 model helicopters or ASB No. 25.00.85, for the AS355 model helicopters, both dated November 16, 2005, as appropriate for your model helicopter. Texas, or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call (202) 741–6030, or go to: https://www.archives.gov/federal-register/ cfr/ibr-locations.html. Differences Between This AD and the MCAI AD (f) This AD differs from the MCAI AD in that it: (1) Does not include the Model BB helicopters but does include the Model AS350C and D1 and Model AS355NP helicopters; (2) Does not require the actions specified in the Compliance section, paragraph 1 of the MCAI AD; (3) Does not address spares; and (4) Requires compliance before the next hoist operation instead of within 30 days. BILLING CODE 4910–13–P Other Information (g) Alternative Methods of Compliance (AMOCs): The Manager, Safety Management Group, FAA, ATTN: George Schwab, Aerospace Engineer, Rotorcraft Directorate, Fort Worth, Texas 76193–0112, telephone (817) 222–5114, fax (817) 222–5961, has the authority to approve AMOCs for this AD, if requested, using the procedures found in 14 CFR 39.19. (h) Special Flight Permits: Special flight permits may be issued under 14 CFR 21.197 and 21.199 to operate the helicopter to a location where the requirements of this AD can be done provided that the hoist is not used. Airworthiness Directives; Eurocopter France (ECF) Model EC120B Helicopters Related Information (i) Mandatory Continuing Airworthiness Information (EASA) Airworthiness Directive No. 2006–0164, dated June 9, 2006, contains related information. mstockstill on DSKH9S0YB1PROD with RULES Joint Aircraft System/Component (JASC) Code (j) The JASC Code is 25: Equipment/ Furnishings. Material Incorporated by Reference (k) You must use the specified portions of Eurocopter Alert Service Bulletin No. 25.00.95 or No. 25.00.85, both dated November 16, 2005, to do the actions required. (1) The Director of the Federal Register approved the incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51. (2) For the service information identified in this AD, contact American Eurocopter Corporation, 2701 Forum Drive, Grand Prairie, Texas 75053–4005, telephone (972) 641–3460, fax (972) 641–3527. (3) You may review copies of the service information at the FAA, Office of the Regional Counsel, Southwest Region, 2601 Meacham Blvd., Room 663, Fort Worth, VerDate Mar<15>2010 16:14 Apr 28, 2010 Jkt 220001 Issued in Fort Worth, Texas, on March 15, 2010. Mark R. Schilling, Acting Manager, Rotorcraft Directorate, Aircraft Certification Service. [FR Doc. 2010–9006 Filed 4–28–10; 8:45 am] DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2010–0410; Directorate Identifier 2010–SW–024–AD; Amendment 39–16265; AD 2010–05–51] RIN 2120–AA64 AGENCY: Federal Aviation Administration, DOT. ACTION: Final rule; request for comments. SUMMARY: This document publishes in the Federal Register an amendment adopting Airworthiness Directive (AD) 2010–05–51, which was sent previously to all known U.S. owners and operators of ECF Model EC120B helicopters by individual letters. This AD requires, at specified intervals, inspecting the main rotor head rotor hub (rotor hub) for a crack. If you find scoring, paint flaking or left-over identification plate adhesive, the AD requires sanding the area until the primer coat becomes visible and inspecting the rotor hub for a crack. If you find a crack, the AD requires, before further flight, replacing the rotor hub with an airworthy rotor hub. This amendment is prompted by a mandatory continuing airworthiness information (MCAI) AD issued by the European Aviation Safety Agency (EASA), which is the Technical Agent for the Member States of the European Community. The MCAI AD states that ECF has been informed of an emergency landing due to excessive vibrations originating from the main rotor. After an investigation, it was determined that the main rotor head rotor hub (rotor hub) had failed in the attachment area of one of the three drag damper fittings. The actions specified by the AD are intended to prevent failure of a hub, excessive vibrations, loss of a main rotor blade, PO 00000 Frm 00008 Fmt 4700 Sfmt 4700 and subsequent loss of control of the helicopter. DATES: Effective May 14, 2010, to all persons except those persons to whom it was made immediately effective by Emergency AD (EAD) 2010–05–51, issued on February 24, 2010, which contained the requirements of this amendment. The incorporation by reference of certain publications listed in the regulations is approved by the Director of the Federal Register as of May 14, 2010. Comments for inclusion in the Rules Docket must be received on or before June 28, 2010. ADDRESSES: Use one of the following addresses to submit comments on this AD: • Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments. • Fax: 202–493–2251. • Mail: U.S. Department of Transportation, Docket Operations, M– 30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue, SE., Washington, DC 20590. • Hand Delivery: U.S. Department of Transportation, Docket Operations, M– 30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue, SE., Washington, DC 20590, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. You may get the service information identified in this AD from American Eurocopter Corporation, 2701 Forum Drive, Grand Prairie, TX 75053–4005, telephone (800) 232–0323, fax (972) 641–3710, or at https:// www.eurocopter.com. Examining the Docket: You may examine the docket that contains the AD, any comments, and other information on the Internet at https:// www.regulations.gov, or in person at the Docket Operations office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The Docket Operations office (telephone (800) 647– 5527) is located in Room W12–140 on the ground floor of the West Building at the street address stated in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt. FOR FURTHER INFORMATION CONTACT: DOT/FAA Southwest Region, Gary Roach, ASW–111, Aviation Safety Engineer, Rotorcraft Directorate, Regulations and Guidance Group, 2601 Meacham Blvd, Fort Worth, Texas 76137, telephone (817) 222–5130, fax (817) 222–5961. SUPPLEMENTARY INFORMATION: On February 24, 2010, the FAA issued EAD E:\FR\FM\29APR1.SGM 29APR1 mstockstill on DSKH9S0YB1PROD with RULES Federal Register / Vol. 75, No. 82 / Thursday, April 29, 2010 / Rules and Regulations 2010–05–51 for the ECF Model EC120B helicopters. This AD requires, within specified intervals, inspecting the rotor hub for a crack and removing the identification plate and cleaning the area. If you find scoring, paint flaking or left-over identification plate adhesive, the AD requires sanding the area until the primer coat becomes visible and inspecting the rotor hub for a crack. If you find a crack, the AD requires, before further flight, replacing the rotor hub with an airworthy rotor hub. This amendment is prompted by an emergency landing due to excessive vibrations originating from the main rotor. After an investigation, it was determined the rotor hub had failed in the attachment area of one of the three drag damper fittings. This condition, if not corrected, could result in failure of a hub, excessive vibrations, loss of a main rotor blade, and subsequent loss of control of the helicopter. EASA, the airworthiness authority for France, notified the FAA that an unsafe condition may exist on these helicopter models. EASA advises of an emergency landing due to a set of amplitude vibrations originating from the main rotor. ECF has issued Emergency Alert Service Bulletin No. 05A012, Revision 1, dated February 19, 2010 (EASB), which specifies inspecting the rotor hub for a crack. Also, if you find local deterioration (scoring or paint spalling), the EASB specifies sanding the area, removing the finish paint until the primer coat becomes visible, and inspecting the area for a crack. If you find a crack, the EASB specifies replacing the affected rotor hub with a new rotor hub. EASA classified this service bulletin as mandatory and issued AD No. 2010– 0026–E, dated February 19, 2010, to ensure the continued airworthiness of these helicopters in France. This AD differs from the MCAI AD in that we refer to flight hours as time-inservice (TIS). Also, we do not require you to contact the manufacturer. This helicopter model is manufactured in France and is type certificated for operation in the United States under the provisions of 14 CFR 21.29 and the applicable bilateral agreement. Pursuant to the applicable bilateral agreement with France, EASA, their technical agent, has kept the FAA informed of the situation described above. The FAA has examined the findings of EASA, reviewed all available information, and determined that AD action is necessary for products of this type design that are certificated for operation in the United States. VerDate Mar<15>2010 16:14 Apr 28, 2010 Jkt 220001 Since the unsafe condition described is likely to exist or develop on other ECF Model EC120B helicopters of the same type design, the FAA issued EAD 2010–05–51. The AD requires, at specified intervals, inspecting the rotor hub for a crack. If you find scoring, paint flaking or left-over identification plate adhesive, the AD requires sanding the area and inspecting the specified areas of the rotor hub for a crack. If you find a crack, the AD requires, before further flight, replacing the rotor hub with an airworthy rotor hub. The actions must be done by following specified portions of the EASB. The short compliance time involved is required because the previously described critical unsafe condition can adversely affect the controllability and structural integrity of the helicopter. Therefore, inspecting the rotor hub for a crack is required within 15 hours TIS, and if you find a crack, replacing the rotor hub with an airworthy rotor hub is required before further flight, and this AD must be issued immediately. Since it was found that immediate corrective action was required, notice and opportunity for prior public comment thereon were impracticable and contrary to the public interest, and good cause existed to make the AD effective immediately by individual letters issued on February 24, 2010, to all known U.S. owners and operators of ECF Model EC120B helicopters. These conditions still exist, and the AD is hereby published in the Federal Register as an amendment to 14 CFR 39.13 to make it effective to all persons. However, we made a minor editorial change in paragraph (a) of this AD. We added the word, ‘‘Eurocopter’’ in front of the words, ‘‘Emergency Alert Service Bulletin,’’ which we inadvertently omitted in the EAD. We have determined that this change will neither increase the economic burden on any operator nor increase the scope of the AD. The FAA estimates that this AD will affect 114 helicopters of U.S. registry, and inspecting the rotor hub for a crack will take a minimal amount of time. It will take about 1 hour to do the sanding, assuming 37 rotor hubs require sanding. It will take about 6 hours to replace a rotor hub, assuming 2 helicopters will require replacement of a rotor hub. The average labor rate is $85 per hour. Required parts will cost about $61,685 per helicopter. Based on these figures, we estimate the total cost impact of the AD on U.S. operators to be $127,535. Comments Invited This AD is a final rule that involves requirements that affect flight safety and PO 00000 Frm 00009 Fmt 4700 Sfmt 4700 22511 was not preceded by notice and an opportunity for public comment; however, we invite you to submit any written data, views, or arguments regarding this AD. Send your comments to an address listed under ADDRESSES. Include ‘‘Docket No. FAA–2010–0410; Directorate Identifier 2010–SW–024– AD’’ at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of the AD. We will consider all comments received by the closing date and may amend the AD in light of those comments. We will post all comments we receive, without change, to https:// www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact with FAA personnel concerning this AD. Using the search function of our docket Web site, you can find and read the comments to any of our dockets, including the name of the individual who sent the comment. You may review the DOT’s complete Privacy Act Statement in the Federal Register published on April 11, 2000 (65 FR 19477–78). Regulatory Findings We have determined that this AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government. For the reasons discussed above, I certify that the regulation: 1. Is not a ‘‘significant regulatory action’’ under Executive Order 12866; 2. Is not a ‘‘significant rule’’ under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and 3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. We prepared an economic evaluation of the estimated costs to comply with this AD. See the AD docket to examine the economic evaluation. Authority for This Rulemaking Title 49 of the United States Code specifies the FAA’s authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII, Aviation Programs, describes in more detail the scope of the Agency’s authority. E:\FR\FM\29APR1.SGM 29APR1 22512 Federal Register / Vol. 75, No. 82 / Thursday, April 29, 2010 / Rules and Regulations We are issuing this rulemaking under the authority described in subtitle VII, part A, subpart III, section 44701, ‘‘General requirements.’’ Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. List of Subjects in 14 CFR Part 39 Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety. Adoption of the Amendment Accordingly, pursuant to the authority delegated to me by the Administrator, the Federal Aviation Administration amends part 39 of the Federal Aviation Regulations (14 CFR part 39) as follows: ■ PART 39—AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows: ■ Authority: 49 U.S.C. 106(g), 40113, 44701. § 39.13 [Amended] 2. Section 39.13 is amended by adding a new airworthiness directive to read as follows: ■ 2010–05–51 Eurocopter France: Amendment 39–16265. Docket No. FAA–2010–0410; Directorate Identifier 2010–SW–024–AD. mstockstill on DSKH9S0YB1PROD with RULES Applicability Model EC120B helicopters, with a main rotor head with a rotor hub, part number (P/ N) C622A1002103, C622A1002104, or C622A1002105, installed, certificated in any category. Compliance Required as indicated. To prevent failure of a main rotor hub, excessive vibrations, loss of a main rotor blade, and subsequent loss of control of the helicopter, do the following: (a) Within 15 hours time-in-service (TIS), unless done previously, and thereafter at intervals not to exceed 15 hours TIS, inspect the rotor hub for a crack in the areas depicted in Figures 1 and 2, areas ‘‘A1’’ and ‘‘A2,’’ of Eurocopter Emergency Alert Service Bulletin No. 05A012, Revision 1, dated February 19, 2010 (EASB). If the identification plate ‘‘b’’ depicted in Figure 2 of the EASB is in the inspection areas ‘‘A1’’ or ‘‘A2,’’ remove the plate and clean the area where the identification plate information will be marked ‘‘B,’’ by following the Accomplishment Instructions, paragraph 2.B.2.a., of the EASB. VerDate Mar<15>2010 16:14 Apr 28, 2010 Jkt 220001 (1) If you find scoring, paint flaking, or leftover identification plate adhesive, sand the area using No. 600-grit (fine grit) abrasive paper until the primer coat becomes visible and inspect the rotor hub for a crack. (2) If you find a crack, before further flight, replace the rotor hub with an airworthy rotor hub. (b) To request a different method of compliance or a different compliance time for this AD, follow the procedures in 14 CFR 39.19. Contact the Manager, Safety Management Group, ATTN: DOT/FAA Southwest Region, Gary Roach, ASW–111, Aviation Safety Engineer, Rotorcraft Directorate, Regulations and Guidance Group, 2601 Meacham Blvd, Fort Worth, Texas 76137, telephone (817) 222–5130, fax (817) 222–5961, for information about previously approved alternative methods of compliance. (c) Special flight permits will not be issued. (d) The Joint Aircraft System/Component (JASC) Code is 6220: Main Rotor Head. (e) The inspections shall be done by following the specified portions of Eurocopter Emergency Alert Service Bulletin No. 05A012, Revision 1, dated February 19, 2010. The Director of the Federal Register approved this incorporation by reference in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be obtained from American Eurocopter Corporation, 2701 Forum Drive, Grand Prairie, TX 75053–4005, telephone (800) 232–0323, fax (972) 641– 3710, or at https://www.eurocopter.com. Copies may be inspected at the FAA, Office of the Regional Counsel, Southwest Region, 2601 Meacham Blvd., Room 663, Fort Worth, Texas or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202–741–6030, or go to: https://www.archives.gov/federal_register/ code_of_federal_regulations/ ibr_locations.html. (f) This amendment becomes effective on May 14, 2010, to all persons except those persons to whom it was made immediately effective by EAD 2010–05–51, issued February 24, 2010, which contained the requirements of this amendment. Note: The subject of this AD is addressed in European Aviation Safety Agency AD No. 2010–0026–E, dated February 19, 2010. Issued in Fort Worth, Texas, on April 12, 2010. Mark R. Schilling, Acting Manager, Rotorcraft Directorate, Aircraft Certification Service. [FR Doc. 2010–9007 Filed 4–28–10; 8:45 am] Frm 00010 Fmt 4700 Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2010–0124 Directorate Identifier 2010–CE–002–AD; Amendment 39–16274; AD 2010–09–09] RIN 2120–AA64 Airworthiness Directives; Piaggio Aero Industries S.p.A. Model PIAGGIO P– 180 Airplanes AGENCY: Federal Aviation Administration (FAA), Department of Transportation (DOT). ACTION: Final rule. SUMMARY: We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: A failure of fuel pump sealing, due to possible incorrect maintenance procedures and subsequent testing, caused a fuel leakage into the main landing gear bay. Presence of fuel vapours in that zone creates a risk of fire due to presence of potential ignition sources such as electrical equipment and connectors. We are issuing this AD to require actions to correct the unsafe condition on these products. DATES: This AD becomes effective June 3, 2010. On June 3, 2010, the Director of the Federal Register approved the incorporation by reference of certain publications listed in this AD. ADDRESSES: You may examine the AD docket on the Internet at https:// www.regulations.gov or in person at Document Management Facility, U.S. Department of Transportation, Docket Operations, M–30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue, SE., Washington, DC 20590. FOR FURTHER INFORMATION CONTACT: Sarjapur Nagarajan, Aerospace Engineer, FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 329– 4145; fax: (816) 329–4090. SUPPLEMENTARY INFORMATION: Discussion We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR part 39 to include an AD that would apply to the specified products. That NPRM was published in the Federal BILLING CODE 4910–13–P PO 00000 DEPARTMENT OF TRANSPORTATION Sfmt 4700 E:\FR\FM\29APR1.SGM 29APR1

Agencies

[Federal Register Volume 75, Number 82 (Thursday, April 29, 2010)]
[Rules and Regulations]
[Pages 22510-22512]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2010-9007]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2010-0410; Directorate Identifier 2010-SW-024-AD; 
Amendment 39-16265; AD 2010-05-51]
RIN 2120-AA64


Airworthiness Directives; Eurocopter France (ECF) Model EC120B 
Helicopters

AGENCY: Federal Aviation Administration, DOT.

ACTION: Final rule; request for comments.

-----------------------------------------------------------------------

SUMMARY: This document publishes in the Federal Register an amendment 
adopting Airworthiness Directive (AD) 2010-05-51, which was sent 
previously to all known U.S. owners and operators of ECF Model EC120B 
helicopters by individual letters. This AD requires, at specified 
intervals, inspecting the main rotor head rotor hub (rotor hub) for a 
crack. If you find scoring, paint flaking or left-over identification 
plate adhesive, the AD requires sanding the area until the primer coat 
becomes visible and inspecting the rotor hub for a crack. If you find a 
crack, the AD requires, before further flight, replacing the rotor hub 
with an airworthy rotor hub. This amendment is prompted by a mandatory 
continuing airworthiness information (MCAI) AD issued by the European 
Aviation Safety Agency (EASA), which is the Technical Agent for the 
Member States of the European Community. The MCAI AD states that ECF 
has been informed of an emergency landing due to excessive vibrations 
originating from the main rotor. After an investigation, it was 
determined that the main rotor head rotor hub (rotor hub) had failed in 
the attachment area of one of the three drag damper fittings. The 
actions specified by the AD are intended to prevent failure of a hub, 
excessive vibrations, loss of a main rotor blade, and subsequent loss 
of control of the helicopter.

DATES: Effective May 14, 2010, to all persons except those persons to 
whom it was made immediately effective by Emergency AD (EAD) 2010-05-
51, issued on February 24, 2010, which contained the requirements of 
this amendment.
    The incorporation by reference of certain publications listed in 
the regulations is approved by the Director of the Federal Register as 
of May 14, 2010.
    Comments for inclusion in the Rules Docket must be received on or 
before June 28, 2010.

ADDRESSES: Use one of the following addresses to submit comments on 
this AD:
     Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
     Fax: 202-493-2251.
     Mail: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue, SE., Washington, DC 20590.
     Hand Delivery: U.S. Department of Transportation, Docket 
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New 
Jersey Avenue, SE., Washington, DC 20590, between 9 a.m. and 5 p.m., 
Monday through Friday, except Federal holidays.
    You may get the service information identified in this AD from 
American Eurocopter Corporation, 2701 Forum Drive, Grand Prairie, TX 
75053-4005, telephone (800) 232-0323, fax (972) 641-3710, or at https://www.eurocopter.com.
    Examining the Docket: You may examine the docket that contains the 
AD, any comments, and other information on the Internet at https://www.regulations.gov, or in person at the Docket Operations office 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The Docket Operations office (telephone (800) 647-5527) is 
located in Room W12-140 on the ground floor of the West Building at the 
street address stated in the ADDRESSES section. Comments will be 
available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: DOT/FAA Southwest Region, Gary Roach, 
ASW-111, Aviation Safety Engineer, Rotorcraft Directorate, Regulations 
and Guidance Group, 2601 Meacham Blvd, Fort Worth, Texas 76137, 
telephone (817) 222-5130, fax (817) 222-5961.

SUPPLEMENTARY INFORMATION: On February 24, 2010, the FAA issued EAD

[[Page 22511]]

2010-05-51 for the ECF Model EC120B helicopters. This AD requires, 
within specified intervals, inspecting the rotor hub for a crack and 
removing the identification plate and cleaning the area. If you find 
scoring, paint flaking or left-over identification plate adhesive, the 
AD requires sanding the area until the primer coat becomes visible and 
inspecting the rotor hub for a crack. If you find a crack, the AD 
requires, before further flight, replacing the rotor hub with an 
airworthy rotor hub. This amendment is prompted by an emergency landing 
due to excessive vibrations originating from the main rotor. After an 
investigation, it was determined the rotor hub had failed in the 
attachment area of one of the three drag damper fittings. This 
condition, if not corrected, could result in failure of a hub, 
excessive vibrations, loss of a main rotor blade, and subsequent loss 
of control of the helicopter.
    EASA, the airworthiness authority for France, notified the FAA that 
an unsafe condition may exist on these helicopter models. EASA advises 
of an emergency landing due to a set of amplitude vibrations 
originating from the main rotor.
    ECF has issued Emergency Alert Service Bulletin No. 05A012, 
Revision 1, dated February 19, 2010 (EASB), which specifies inspecting 
the rotor hub for a crack. Also, if you find local deterioration 
(scoring or paint spalling), the EASB specifies sanding the area, 
removing the finish paint until the primer coat becomes visible, and 
inspecting the area for a crack. If you find a crack, the EASB 
specifies replacing the affected rotor hub with a new rotor hub.
    EASA classified this service bulletin as mandatory and issued AD 
No. 2010-0026-E, dated February 19, 2010, to ensure the continued 
airworthiness of these helicopters in France.
    This AD differs from the MCAI AD in that we refer to flight hours 
as time-in-service (TIS). Also, we do not require you to contact the 
manufacturer.
    This helicopter model is manufactured in France and is type 
certificated for operation in the United States under the provisions of 
14 CFR 21.29 and the applicable bilateral agreement. Pursuant to the 
applicable bilateral agreement with France, EASA, their technical 
agent, has kept the FAA informed of the situation described above. The 
FAA has examined the findings of EASA, reviewed all available 
information, and determined that AD action is necessary for products of 
this type design that are certificated for operation in the United 
States.
    Since the unsafe condition described is likely to exist or develop 
on other ECF Model EC120B helicopters of the same type design, the FAA 
issued EAD 2010-05-51. The AD requires, at specified intervals, 
inspecting the rotor hub for a crack. If you find scoring, paint 
flaking or left-over identification plate adhesive, the AD requires 
sanding the area and inspecting the specified areas of the rotor hub 
for a crack. If you find a crack, the AD requires, before further 
flight, replacing the rotor hub with an airworthy rotor hub. The 
actions must be done by following specified portions of the EASB. The 
short compliance time involved is required because the previously 
described critical unsafe condition can adversely affect the 
controllability and structural integrity of the helicopter. Therefore, 
inspecting the rotor hub for a crack is required within 15 hours TIS, 
and if you find a crack, replacing the rotor hub with an airworthy 
rotor hub is required before further flight, and this AD must be issued 
immediately.
    Since it was found that immediate corrective action was required, 
notice and opportunity for prior public comment thereon were 
impracticable and contrary to the public interest, and good cause 
existed to make the AD effective immediately by individual letters 
issued on February 24, 2010, to all known U.S. owners and operators of 
ECF Model EC120B helicopters. These conditions still exist, and the AD 
is hereby published in the Federal Register as an amendment to 14 CFR 
39.13 to make it effective to all persons. However, we made a minor 
editorial change in paragraph (a) of this AD. We added the word, 
``Eurocopter'' in front of the words, ``Emergency Alert Service 
Bulletin,'' which we inadvertently omitted in the EAD. We have 
determined that this change will neither increase the economic burden 
on any operator nor increase the scope of the AD.
    The FAA estimates that this AD will affect 114 helicopters of U.S. 
registry, and inspecting the rotor hub for a crack will take a minimal 
amount of time. It will take about 1 hour to do the sanding, assuming 
37 rotor hubs require sanding. It will take about 6 hours to replace a 
rotor hub, assuming 2 helicopters will require replacement of a rotor 
hub. The average labor rate is $85 per hour. Required parts will cost 
about $61,685 per helicopter. Based on these figures, we estimate the 
total cost impact of the AD on U.S. operators to be $127,535.

Comments Invited

    This AD is a final rule that involves requirements that affect 
flight safety and was not preceded by notice and an opportunity for 
public comment; however, we invite you to submit any written data, 
views, or arguments regarding this AD. Send your comments to an address 
listed under ADDRESSES. Include ``Docket No. FAA-2010-0410; Directorate 
Identifier 2010-SW-024-AD'' at the beginning of your comments. We 
specifically invite comments on the overall regulatory, economic, 
environmental, and energy aspects of the AD. We will consider all 
comments received by the closing date and may amend the AD in light of 
those comments.
    We will post all comments we receive, without change, to https://www.regulations.gov, including any personal information you provide. We 
will also post a report summarizing each substantive verbal contact 
with FAA personnel concerning this AD. Using the search function of our 
docket Web site, you can find and read the comments to any of our 
dockets, including the name of the individual who sent the comment. You 
may review the DOT's complete Privacy Act Statement in the Federal 
Register published on April 11, 2000 (65 FR 19477-78).

Regulatory Findings

    We have determined that this AD will not have federalism 
implications under Executive Order 13132. This AD will not have a 
substantial direct effect on the States, on the relationship between 
the national Government and the States, or on the distribution of power 
and responsibilities among the various levels of government.
    For the reasons discussed above, I certify that the regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979); and
    3. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared an economic evaluation of the estimated costs to comply 
with this AD. See the AD docket to examine the economic evaluation.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII, Aviation Programs, 
describes in more detail the scope of the Agency's authority.

[[Page 22512]]

    We are issuing this rulemaking under the authority described in 
subtitle VII, part A, subpart III, section 44701, ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by 
reference, Safety.

Adoption of the Amendment

0
Accordingly, pursuant to the authority delegated to me by the 
Administrator, the Federal Aviation Administration amends part 39 of 
the Federal Aviation Regulations (14 CFR part 39) as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

    Authority:  49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

0
2. Section 39.13 is amended by adding a new airworthiness directive to 
read as follows:

2010-05-51 Eurocopter France: Amendment 39-16265. Docket No. FAA-
2010-0410; Directorate Identifier 2010-SW-024-AD.

Applicability

    Model EC120B helicopters, with a main rotor head with a rotor 
hub, part number (P/N) C622A1002103, C622A1002104, or C622A1002105, 
installed, certificated in any category.

Compliance

    Required as indicated.
    To prevent failure of a main rotor hub, excessive vibrations, 
loss of a main rotor blade, and subsequent loss of control of the 
helicopter, do the following:
    (a) Within 15 hours time-in-service (TIS), unless done 
previously, and thereafter at intervals not to exceed 15 hours TIS, 
inspect the rotor hub for a crack in the areas depicted in Figures 1 
and 2, areas ``A1'' and ``A2,'' of Eurocopter Emergency Alert 
Service Bulletin No. 05A012, Revision 1, dated February 19, 2010 
(EASB). If the identification plate ``b'' depicted in Figure 2 of 
the EASB is in the inspection areas ``A1'' or ``A2,'' remove the 
plate and clean the area where the identification plate information 
will be marked ``B,'' by following the Accomplishment Instructions, 
paragraph 2.B.2.a., of the EASB.
    (1) If you find scoring, paint flaking, or left-over 
identification plate adhesive, sand the area using No. 600-grit 
(fine grit) abrasive paper until the primer coat becomes visible and 
inspect the rotor hub for a crack.
    (2) If you find a crack, before further flight, replace the 
rotor hub with an airworthy rotor hub.
    (b) To request a different method of compliance or a different 
compliance time for this AD, follow the procedures in 14 CFR 39.19. 
Contact the Manager, Safety Management Group, ATTN: DOT/FAA 
Southwest Region, Gary Roach, ASW-111, Aviation Safety Engineer, 
Rotorcraft Directorate, Regulations and Guidance Group, 2601 Meacham 
Blvd, Fort Worth, Texas 76137, telephone (817) 222-5130, fax (817) 
222-5961, for information about previously approved alternative 
methods of compliance.
    (c) Special flight permits will not be issued.
    (d) The Joint Aircraft System/Component (JASC) Code is 6220: 
Main Rotor Head.
    (e) The inspections shall be done by following the specified 
portions of Eurocopter Emergency Alert Service Bulletin No. 05A012, 
Revision 1, dated February 19, 2010. The Director of the Federal 
Register approved this incorporation by reference in accordance with 
5 U.S.C. 552(a) and 1 CFR part 51. Copies may be obtained from 
American Eurocopter Corporation, 2701 Forum Drive, Grand Prairie, TX 
75053-4005, telephone (800) 232-0323, fax (972) 641-3710, or at 
https://www.eurocopter.com. Copies may be inspected at the FAA, 
Office of the Regional Counsel, Southwest Region, 2601 Meacham 
Blvd., Room 663, Fort Worth, Texas or at the National Archives and 
Records Administration (NARA). For information on the availability 
of this material at NARA, call 202-741-6030, or go to: https://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.
    (f) This amendment becomes effective on May 14, 2010, to all 
persons except those persons to whom it was made immediately 
effective by EAD 2010-05-51, issued February 24, 2010, which 
contained the requirements of this amendment.

    Note:  The subject of this AD is addressed in European Aviation 
Safety Agency AD No. 2010-0026-E, dated February 19, 2010.


    Issued in Fort Worth, Texas, on April 12, 2010.
Mark R. Schilling,
Acting Manager, Rotorcraft Directorate, Aircraft Certification Service.
[FR Doc. 2010-9007 Filed 4-28-10; 8:45 am]
BILLING CODE 4910-13-P
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.