Delegation of National Emission Standards for Hazardous Air Pollutants for Source Categories; State of Arizona, Arizona Department of Environmental Quality, Pima County Department of Environmental Quality, 47546-47550 [E8-18748]
Download as PDF
<![CDATA[
47546
Federal Register / Vol. 73, No. 158 / Thursday, August 14, 2008 / Rules and Regulations
rfrederick on PROD1PC67 with RULES
number of fuels approved into SIPs
under section 211(c)(4)(C) as of
September 1, 2004. Therefore, EPA is
again approving the BACM
demonstration in the MAG plan for the
on-road source category without CARB
diesel. Because EPA has found that
CARB diesel is not feasible for nonroad
engines and equipment because of the
uncertainties with fuel availability,
storage and segregation and concerns
about program effectiveness due to
owners and operators fueling outside
the Maricopa County area, we are again
approving BACM demonstration in the
MAG plan for the nonroad source
category without CARB diesel. For the
reasons discussed above, EPA is also
again approving the MSM
demonstration in the MAG plan and is
confirming that we appropriately
granted in 2002 and 2006 the State’s
request for an extension of the
attainment deadline for the area from
December 31, 2001 to December 31,
2006. These actions are codified at 40
CFR 52.123(j)(2), (4) and (7) and remain
in effect. See 67 FR at 48739.
IV. Statutory and Executive Order
Reviews
Under Executive Order 12866 (58 FR
51735, October 4, 1993), this action is
not a ‘‘significant regulatory action’’ and
therefore is not subject to review by the
Office of Management and Budget. For
this reason, this action is also not
subject to Executive Order 13211,
‘‘Actions Concerning Regulations That
Significantly Affect Energy Supply,
Distribution, or Use’’ (66 FR 28355, May
22, 2001). This action merely approves
state law as meeting Federal
requirements and imposes no additional
requirements beyond those imposed by
state law. Accordingly, the
Administrator certifies that this rule
will not have a significant economic
impact on a substantial number of small
entities under the Regulatory Flexibility
Act (5 U.S.C. 601 et seq.). Because this
rule approves pre-existing requirements
under state law and does not impose
any additional enforceable duty beyond
that required by state law, it does not
contain any unfunded mandate or
significantly or uniquely affect small
governments, as described in the
Unfunded Mandates Reform Act of 1995
(Pub. L. 104–4).
This rule also does not have tribal
implications because it will not have a
substantial direct effect on one or more
Indian tribes, on the relationship
between the Federal Government and
Indian tribes, or on the distribution of
power and responsibilities between the
Federal Government and Indian tribes,
as specified by Executive Order 13175
VerDate Aug<31>2005
14:45 Aug 13, 2008
Jkt 214001
(65 FR 67249, November 9, 2000). This
action also does not have Federalism
implications because it does not have
substantial direct effects on the States,
on the relationship between the national
government and the States, or on the
distribution of power and
responsibilities among the various
levels of government, as specified in
Executive Order 13132 (64 FR 43255,
August 10, 1999). This action merely
approves a state rule implementing a
Federal standard, and does not alter the
relationship or the distribution of power
and responsibilities established in the
Clean Air Act. Executive Order 12898
(59 FR 7629, February 16, 1994)
establishes a Federal policy for
incorporating environmental justice into
Federal agency actions by directing
agencies to identify and address, as
appropriate, disproportionately high
and adverse human health or
environmental effects of their programs,
policies, and activities on minority and
low-income populations. Today’s action
will not have disproportionately high
and adverse effects on any communities
in the area, including minority and lowincome communities.
This rule also is not subject to
Executive Order 13045 ‘‘Protection of
Children from Environmental Health
Risks and Safety Risks’’ (62 FR 19885,
April 23, 1997), because it is not
economically significant.
The requirements of section 12(d) of
the National Technology Transfer and
Advancement Act of 1995 (15 U.S.C.
272 note) do not apply. This rule does
not impose an information collection
burden under the provisions of the
Paperwork Reduction Act of 1995 (44
U.S.C. 3501 et seq.).
The Congressional Review Act, 5
U.S.C. section 801 et seq., as added by
the Small Business Regulatory
Enforcement Fairness Act of 1996,
generally provides that before a rule
may take effect, the agency
promulgating the rule must submit a
rule report, which includes a copy of
the rule, to each House of the Congress
and to the Comptroller General of the
United States. EPA will submit a report
containing this rule and other required
information to the U.S. Senate, the U.S.
House of Representatives, and the
Comptroller General of the United
States prior to publication of the rule in
the Federal Register. A major rule
cannot take effect until 60 days after it
is published in the Federal Register.
This action is not a ‘‘major rule’’ as
defined by 5 U.S.C. 804(2).
Under section 307(b)(1) of the Clean
Air Act, petitions for judicial review of
this action must be filed in the United
States Court of Appeals for the
PO 00000
Frm 00024
Fmt 4700
Sfmt 4700
appropriate circuit by October 14, 2008.
Filing a petition for reconsideration by
the Administrator of this final rule does
not affect the finality of this rule for the
purposes of judicial review nor does it
extend the time within which a petition
for judicial review may be filed, and
shall not postpone the effectiveness of
such rule or action. This action may not
be challenged later in proceedings to
enforce its requirements. (See section
307(b)(2).)
List of Subjects in 40 CFR Part 52
Environmental protection, Air
pollution control, Intergovernmental
relations, Particulate matter, Reporting
and recordkeeping requirements.
Dated: August 4, 2008.
Laura Yoshii,
Acting Regional Administrator, Region IX.
[FR Doc. E8–18626 Filed 8–13–08; 8:45 am]
BILLING CODE 6560–50–P
ENVIRONMENTAL PROTECTION
AGENCY
40 CFR Part 63
[EPA–R09–OAR–2008–0555; FRL–8701–7]
Delegation of National Emission
Standards for Hazardous Air Pollutants
for Source Categories; State of
Arizona, Arizona Department of
Environmental Quality, Pima County
Department of Environmental Quality
Environmental Protection
Agency (EPA).
AGENCY:
ACTION:
Direct final rule.
SUMMARY: EPA is amending certain
regulations to reflect the current
delegation status of national emission
standards for hazardous air pollutants
(NESHAP) in Arizona. Several NESHAP
were delegated to the Arizona
Department of Environmental Quality
on June 4, 2008, and to the Pima County
Department of Environmental Quality
on June 16, 2008. The purpose of this
action is to update the listing in the
Code of Federal Regulations.
This rule is effective on October
14, 2008, without further notice, unless
EPA receives adverse comments by
September 15, 2008. If we receive such
comments, we will publish a timely
withdrawal in the Federal Register to
notify the public that this direct final
rule will not take effect.
DATES:
Submit comments,
identified by docket number EPA–R09–
OAR–2008–0555, by one of the
following methods:
ADDRESSES:
E:\FR\FM\14AUR1.SGM
14AUR1
Federal Register / Vol. 73, No. 158 / Thursday, August 14, 2008 / Rules and Regulations
1. Federal eRulemaking Portal:
www.regulations.gov. Follow the on-line
instructions.
2. E-mail: steckel.andrew@epa.gov.
3. Mail or delivery: Andrew Steckel
(AIR–4), U.S. Environmental Protection
Agency Region IX, 75 Hawthorne Street,
San Francisco, CA 94105–3901.
Instructions: All comments will be
included in the public docket without
change and may be made available
online at www.regulations.gov,
including any personal information
provided, unless the comment includes
Confidential Business Information (CBI)
or other information whose disclosure is
restricted by statute. Information that
you consider CBI or otherwise protected
should be clearly identified as such and
should not be submitted through
www.regulations.gov or e-mail.
www.regulations.gov is an ‘‘anonymous
access’’ system, and EPA will not know
your identity or contact information
unless you provide it in the body of
your comment. If you send e-mail
directly to EPA, your e-mail address
will be automatically captured and
included as part of the public comment.
If EPA cannot read your comment due
to technical difficulties and cannot
contact you for clarification, EPA may
not be able to consider your comment.
Docket: The index to the docket for
this action is available electronically at
www.regulations.gov and in hard copy
at EPA Region IX, 75 Hawthorne Street,
San Francisco, California. While all
documents in the docket are listed in
the index, some information may be
publicly available only at the hard copy
location (e.g., copyrighted material), and
some may not be publicly available in
either location (e.g., CBI). To inspect the
hard copy materials, please schedule an
appointment during normal business
hours with the contact listed in the FOR
FURTHER INFORMATION CONTACT section.
FOR FURTHER INFORMATION CONTACT: Mae
Wang, EPA Region IX, (415) 947–4124,
wang.mae@epa.gov.
SUPPLEMENTARY INFORMATION:
Throughout this document, ‘‘we,’’ ‘‘us’’
and ‘‘our’’ refer to EPA.
A. Delegation of NESHAP
B. ADEQ Delegations
On July 17, 1998, EPA published a
direct final action delegating to the
Arizona Department of Environmental
Quality (ADEQ) several NESHAP and
approving ADEQ’s delegation
mechanism for future standards (see 63
FR 38478). That action explained the
procedure for EPA to grant delegations
to ADEQ by letter, with periodic
Federal Register listings of standards
that have been delegated. On April 17,
2008, ADEQ requested delegation of the
following NESHAP contained in 40 CFR
part 63:
• Subpart DDDD—NESHAP: Plywood
and Composite Wood Products
• Subpart DDDDD—NESHAP for
Industrial, Commercial, and
Institutional Boilers and Process Heaters
On June 4, 2008, EPA granted
delegation to ADEQ for these NESHAP,
along with any amendments to
previously-delegated NESHAP, as of
July 1, 2006. Today’s action is serving
to notify the public of the June 4, 2008,
delegations and to codify these
delegations into the Code of Federal
Regulations.
Section 112(l) of the Clean Air Act, as
amended in 1990 (CAA), authorizes
EPA to delegate to state or local air
C. PDEQ Delegations
On June 28, 1999, EPA published a
direct final action delegating to the Pima
Table of Contents
I. Background
A. Delegation of NESHAP
B. ADEQ Delegations
C. PDEQ Delegations
II. EPA Action
III. Statutory and Executive Order Reviews
rfrederick on PROD1PC67 with RULES
pollution control agencies the authority
to implement and enforce the standards
set out in the Code of Federal
Regulations, Title 40 (40 CFR), part 63,
National Emission Standards for
Hazardous Air Pollutants for Source
Categories. On November 26, 1993, EPA
promulgated regulations, codified at 40
CFR part 63, Subpart E (hereinafter
referred to as ‘‘Subpart E’’), establishing
procedures for EPA’s approval of state
rules or programs under section 112(l)
(see 58 FR 62262). Subpart E was later
amended on September 14, 2000 (see 65
FR 55810).
Any request for approval under CAA
section 112(l) must meet the approval
criteria in 112(l)(5) and Subpart E. To
streamline the approval process for
future applications, a state or local
agency may submit a one-time
demonstration that it has adequate
authorities and resources to implement
and enforce any CAA section 112
standards. If such demonstration is
approved, then the state or local agency
would no longer need to resubmit a
demonstration of these same authorities
and resources for every subsequent
request for delegation of CAA section
112 standards. However, EPA maintains
the authority to withdraw its approval if
the State does not adequately
implement or enforce an approved rule
or program.
I. Background
VerDate Aug<31>2005
14:45 Aug 13, 2008
Jkt 214001
PO 00000
Frm 00025
Fmt 4700
Sfmt 4700
47547
County Department of Environmental
Quality (PDEQ) several NESHAP and
approving PDEQ’s delegation
mechanism for future standards (see 64
FR 34560). That action explained the
procedure for EPA to grant delegations
to PDEQ by letter, with periodic Federal
Register listings of standards that have
been delegated. On May 23, 2008, PDEQ
requested delegation of the following
NESHAP contained in 40 CFR part 63:
• Subpart J—NESHAP for Polyvinyl
Chloride and Copolymers Production
• Subpart MM—NESHAP for
Chemical Recovery Combustion Sources
at Kraft, Soda, Sulfite, and Stand-Alone
Semichemical Pulp Mills
• Subpart XX—National Emission
Standards for Ethylene Manufacturing
Process Units: Heat Exchange Systems
and Waste Operations
• Subpart DDDD—NESHAP: Plywood
and Composite Wood Products
• Subpart WWWWW—National
Emission Standards for Hospital
Ethylene Oxide Sterilizers
• Subpart YYYYY—NESHAP for Area
Sources: Electric Arc Furnace
Steelmaking Facilities
• Subpart ZZZZZ—NESHAP for Iron
and Steel Foundries Area Sources
• Subpart BBBBBB—NESHAP for
Source Category: Gasoline Distribution
Bulk Terminals, Bulk Plants, and
Pipeline Facilities
• Subpart CCCCCC—NESHAP for
Source Category: Gasoline Dispensing
Facilities
• Subpart DDDDDD—NESHAP for
Polyvinyl Chloride and Copolymers
Production Area Sources
• Subpart EEEEEE—NESHAP for
Primary Copper Smelting Area Sources
• Subpart FFFFFF—NESHAP for
Secondary Copper Smelting Area
Sources
• Subpart GGGGGG—NESHAP for
Primary Nonferrous Metals Area
Sources—Zinc, Cadmium, and
Beryllium
• Subpart HHHHHH—NESHAP:
Paint Stripping and Miscellaneous
Surface Coating Operations at Area
Sources
• Subpart LLLLLL—NESHAP for
Acrylic and Modacrylic Fibers
Production Area Sources
• Subpart MMMMMM—NESHAP for
Carbon Black Production Area Sources
• Subpart NNNNNN—NESHAP for
Chemical Manufacturing Area Sources:
Chromium Compounds
• Subpart OOOOOO—NESHAP for
Flexible Polyurethane Foam Production
and Fabrication Area Sources
• Subpart PPPPPP—NESHAP for
Lead Acid Battery Manufacturing Area
Sources
• Subpart QQQQQQ—NESHAP for
Wood Preserving Area Sources
E:\FR\FM\14AUR1.SGM
14AUR1
47548
Federal Register / Vol. 73, No. 158 / Thursday, August 14, 2008 / Rules and Regulations
• Subpart RRRRRR—NESHAP for
Clay Ceramics Manufacturing Area
Sources
• Subpart SSSSSS—NESHAP for
Glass Manufacturing Area Sources
• Subpart TTTTTT—NESHAP for
Secondary Nonferrous Metals
Processing Area Sources
On June 16, 2008, EPA granted
delegation to PDEQ for these NESHAP,
along with any amendments to
previously-delegated NESHAP, as of
February 1, 2008. Today’s action is
serving to notify the public of the June
16, 2008, delegations and to codify these
delegations into the Code of Federal
Regulations.
II. EPA Action
Today’s document serves to notify the
public of the delegation of NESHAP to
ADEQ on June 4, 2008, and to PDEQ on
June 16, 2008. Today’s action will
codify these delegations into the Code of
Federal Regulations.
III. Statutory and Executive Order
Reviews
Under the Clean Air Act, the
Administrator is required to approve a
delegation request that complies with
the provisions of the Act and applicable
Federal regulations. 42 U.S.C. 7412(l);
40 CFR 63.91(b). Thus, in reviewing
state delegation submissions, our role is
to approve state choices, provided that
they meet the criteria of the CAA.
Accordingly, this action merely updates
the list of approved delegations in the
Code of Federal Regulations and does
not impose additional requirements
beyond those imposed by state law. For
that reason, this action:
• Is not a ‘‘significant regulatory
action’’ subject to review by the Office
of Management and Budget under
Executive Order 12866 (58 FR 51735,
October 4, 1993);
• Does not impose an information
collection burden under the provisions
of the Paperwork Reduction Act (44
U.S.C. 3501 et seq.);
• Is certified as not having a
significant economic impact on a
substantial number of small entities
under the Regulatory Flexibility Act (5
U.S.C. 601 et seq.);
• Does not contain any unfunded
mandate or significantly or uniquely
affect small governments, as described
in the Unfunded Mandates Reform Act
of 1995 (Pub. L. 104–4);
• Does not have Federalism
implications as specified in Executive
Order 13132 (64 FR 43255, August 10,
1999);
• Is not an economically significant
regulatory action based on health or
safety risks subject to Executive Order
13045 (62 FR 19885, April 23, 1997);
• Is not a significant regulatory action
subject to Executive Order 13211 (66 FR
28355, May 22, 2001);
• Is not subject to requirements of
Section 12(d) of the National
Technology Transfer and Advancement
Act of 1995 (15 U.S.C. 272 note) because
application of those requirements would
be inconsistent with the Clean Air Act;
and
• Does not provide EPA with the
discretionary authority to address, as
appropriate, disproportionate human
health or environmental effects, using
practicable and legally permissible
methods, under Executive Order 12898
(59 FR 7629, February 16, 1994).
In addition, this rule does not have
tribal implications as specified by
Executive Order 13175 (65 FR 67249,
November 9, 2000), because the
delegation submission is not approved
to apply in Indian country located in the
state, and EPA notes that it will not
impose substantial direct costs on tribal
governments or preempt tribal law.
The Congressional Review Act, 5
U.S.C. 801 et seq., as added by the Small
Business Regulatory Enforcement
Fairness Act of 1996, generally provides
that before a rule may take effect, the
agency promulgating the rule must
submit a rule report, which includes a
copy of the rule, to each House of the
Congress and to the Comptroller General
of the United States. EPA will submit a
report containing this action and other
required information to the U.S. Senate,
the U.S. House of Representatives, and
the Comptroller General of the United
States prior to publication of the rule in
the Federal Register. A major rule
cannot take effect until 60 days after it
is published in the Federal Register.
This action is not a ‘‘major rule’’ as
defined by 5 U.S.C. 804(2).
Under section 307(b)(1) of the Clean
Air Act, petitions for judicial review of
this action must be filed in the United
States Court of Appeals for the
appropriate circuit by October 14, 2008.
Filing a petition for reconsideration by
the Administrator of this final rule does
not affect the finality of this action for
the purposes of judicial review nor does
it extend the time within which a
petition for judicial review may be filed,
and shall not postpone the effectiveness
of such rule or action. This action may
not be challenged later in proceedings to
enforce its requirements (see section
307(b)(2)).
List of Subjects in 40 CFR Part 63
Environmental protection,
Administrative practice and procedure,
Air pollution control, Hazardous
substances, Intergovernmental relations,
Reporting and recordkeeping
requirements.
Authority: This action is issued under the
authority of Section 112 of the Clean Air Act,
as amended, 42 U.S.C. 7412.
Dated: July 25, 2008.
Amy Zimpfer,
Acting Director, Air Division, Region IX.
Title 40, chapter I, part 63 of the Code
of Federal Regulations is amended as
follows:
I
PART 63—[AMENDED]
1. The authority citation for part 63
continues to read as follows:
I
Authority: 42 U.S.C. 7401, et seq.
Subpart E—Approval of State
Programs and Delegation of Federal
Authorities
2. Section 63.99 is amended by
revising paragraph (a)(3) to read as
follows:
I
§ 63.99
Delegated Federal authorities.
(a) * * *
(3) The following table lists the
specific part 63 standards that have
been delegated unchanged to the air
pollution control agencies in the State of
Arizona. The (X) symbol is used to
indicate each category that has been
delegated.
DELEGATION STATUS FOR PART 63 STANDARDS—ARIZONA
rfrederick on PROD1PC67 with RULES
Subpart
Description
ADEQ 1
MCAQD 2
PDEQ 3
PCAQCD 4
A ...................
F ...................
G ...................
General Provisions ..............................................................................................
Synthetic Organic Chemical Manufacturing Industry ..........................................
Synthetic Organic Chemical Manufacturing Industry: Process Vents, Storage
Vessels, Transfer Operations, and Wastewater.
Organic Hazardous Air Pollutants: Equipment Leaks ........................................
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
H ...................
VerDate Aug<31>2005
14:45 Aug 13, 2008
Jkt 214001
PO 00000
Frm 00026
Fmt 4700
Sfmt 4700
E:\FR\FM\14AUR1.SGM
14AUR1
Federal Register / Vol. 73, No. 158 / Thursday, August 14, 2008 / Rules and Regulations
47549
DELEGATION STATUS FOR PART 63 STANDARDS—ARIZONA—Continued
Subpart
Description
ADEQ 1
MCAQD 2
PDEQ 3
PCAQCD 4
I .....................
Organic Hazardous Air Pollutants: Certain Processes Subject to the Negotiated Regulation for Equipment Leaks.
Polyvinyl Chloride and Copolymers Production ..................................................
Coke Oven Batteries ...........................................................................................
Perchloroethylene Dry Cleaning .........................................................................
Hard and Decorative Chromium Electroplating and Chromium Anodizing
Tanks.
Ethylene Oxide Sterilization Facilities .................................................................
Industrial Process Cooling Towers .....................................................................
Gasoline Distribution Facilities ............................................................................
Pulp and Paper ...................................................................................................
Halogenated Solvent Cleaning ...........................................................................
Group I Polymers and Resins .............................................................................
Epoxy Resins Production and Non-Nylon Polyamides Production ....................
Secondary Lead Smelting ...................................................................................
Phosphoric Acid Manufacturing Plants ...............................................................
Phosphate Fertilizers Production Plants .............................................................
Petroleum Refineries ...........................................................................................
Off-Site Waste and Recovery Operations ..........................................................
Magnetic Tape Manufacturing Operations ..........................................................
Aerospace Manufacturing and Rework Facilities ...............................................
Oil and Natural Gas Production Facilities ...........................................................
Wood Furniture Manufacturing Operations .........................................................
Printing and Publishing Industry .........................................................................
Primary Aluminum Reduction Plants ..................................................................
Chemical Recovery Combustion Sources at Kraft, Soda, Sulfite, and StandAlone Semichemical Pulp Mills.
Tanks—Level 1 ...................................................................................................
Containers ...........................................................................................................
Surface Impoundments .......................................................................................
Individual Drain Systems ....................................................................................
Closed Vent Systems, Control Devices, Recovery Devices and Routing to a
Fuel Gas System or a Process.
Equipment Leaks—Control Level 1 ....................................................................
Equipment Leaks—Control Level 2 ....................................................................
Oil-Water Separators and Organic-Water Separators ........................................
Storage Vessels (Tanks)—Control Level 2 ........................................................
Ethylene Manufacturing Process Units: Heat Exchange Systems and Waste
Operations.
Generic MACT Standards ...................................................................................
Steel Pickling .......................................................................................................
Mineral Wool Production .....................................................................................
Hazardous Waste Combustors ...........................................................................
Pharmaceuticals Production ...............................................................................
Natural Gas Transmission and Storage Facilities ..............................................
Flexible Polyurethane Foam Production .............................................................
Group IV Polymers and Resins ..........................................................................
Portland Cement Manufacturing Industry ...........................................................
Pesticide Active Ingredient Production ...............................................................
Wool Fiberglass Manufacturing ..........................................................................
Manufacture of Amino/Phenolic Resins ..............................................................
Polyether Polyols Production ..............................................................................
Primary Copper Smelting ....................................................................................
Secondary Aluminum Production ........................................................................
Primary Lead Smelting ........................................................................................
Petroleum Refineries: Catalytic Cracking, Catalytic Reforming, and Sulfur Recovery Units.
Publicly Owned Treatment Works ......................................................................
Ferroalloys Production ........................................................................................
Municipal Solid Waste Landfills ..........................................................................
Manufacturing of Nutritional Yeast ......................................................................
Plywood and Composite Wood Products ...........................................................
Organic Liquids Distribution (non-gasoline) ........................................................
Miscellaneous Organic Chemical Manufacturing ................................................
Solvent Extraction for Vegetable Oil Production ................................................
Wet-Formed Fiberglass Mat Production .............................................................
Surface Coating of Automobiles and Light-Duty Trucks ....................................
Paper and Other Web Coating ...........................................................................
Surface Coating of Metal Cans ...........................................................................
Miscellaneous Metal Parts and Products ...........................................................
Large Appliances ................................................................................................
Printing, Coating, and Dyeing of Fabrics and Other Textiles .............................
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
.................
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
................
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
.................
X
X
X
X
.................
.................
X
X
X
X
.................
X
X
.................
.................
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
.................
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
.................
.................
X
.................
.................
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
.................
.................
.................
.................
.................
.................
.................
X
.................
.................
.................
.................
.................
.................
.................
.................
.................
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
................
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
................
X
X
X
X
X
.................
.................
.................
.................
.................
.................
.................
.................
.................
.................
.................
.................
.................
.................
.................
J ....................
L ....................
M ...................
N ...................
O ...................
Q ...................
R ...................
S ...................
T ...................
U ...................
W ..................
X ...................
AA .................
BB .................
CC ................
DD ................
EE .................
GG ................
HH ................
JJ ..................
KK .................
LL ..................
MM ................
OO ................
PP .................
QQ ................
RR ................
SS .................
TT .................
UU ................
VV .................
WW ...............
XX .................
rfrederick on PROD1PC67 with RULES
YY .................
CCC ..............
DDD ..............
EEE ..............
GGG .............
HHH ..............
III ...................
JJJ ................
LLL ................
MMM .............
NNN ..............
OOO .............
PPP ..............
QQQ .............
RRR ..............
TTT ...............
UUU ..............
VVV ..............
XXX ..............
AAAA ............
CCCC ...........
DDDD ...........
EEEE ............
FFFF .............
GGGG ..........
HHHH ...........
IIII ..................
JJJJ ..............
KKKK ............
MMMM ..........
NNNN ...........
OOOO ..........
VerDate Aug<31>2005
14:45 Aug 13, 2008
Jkt 214001
PO 00000
Frm 00027
Fmt 4700
Sfmt 4700
E:\FR\FM\14AUR1.SGM
14AUR1
47550
Federal Register / Vol. 73, No. 158 / Thursday, August 14, 2008 / Rules and Regulations
DELEGATION STATUS FOR PART 63 STANDARDS—ARIZONA—Continued
Subpart
Description
ADEQ 1
MCAQD 2
PDEQ 3
PCAQCD 4
PPPP ............
QQQQ ..........
RRRR ...........
SSSS ............
TTTT .............
UUUU ...........
VVVV ............
WWWW ........
XXXX ............
YYYY ............
ZZZZ .............
AAAAA ..........
BBBBB ..........
CCCCC .........
DDDDD .........
EEEEE ..........
FFFFF ...........
GGGGG ........
HHHHH .........
IIIII .................
JJJJJ .............
KKKKK ..........
LLLLL ............
MMMMM .......
NNNNN .........
PPPPP ..........
QQQQQ ........
RRRRR .........
SSSSS ..........
TTTTT ...........
WWWWW .....
YYYYY ..........
ZZZZZ ...........
BBBBBB .......
CCCCCC ......
DDDDDD ......
EEEEEE .......
FFFFFF ........
GGGGGG .....
HHHHHH ......
Surface Coating of Plastic Parts and Products ..................................................
Wood Building Products ......................................................................................
Surface Coating of Metal Furniture .....................................................................
Surface Coating of Metal Coil .............................................................................
Leather Finishing Operations ..............................................................................
Cellulose Products Manufacturing ......................................................................
Boat Manufacturing .............................................................................................
Reinforced Plastics Composites Production .......................................................
Tire Manufacturing ..............................................................................................
Stationary Combustion Turbines .........................................................................
Stationary Reciprocating Internal Combustion Engines .....................................
Lime Manufacturing Plants .................................................................................
Semiconductor Manufacturing ............................................................................
Coke Oven: Pushing, Quenching and Battery Stacks ........................................
Industrial, Commercial, and Institutional Boiler and Process Heaters ...............
Iron and Steel Foundries ....................................................................................
Integrated Iron and Steel ....................................................................................
Site Remediation .................................................................................................
Miscellaneous Coating Manufacturing ................................................................
Mercury Emissions from Mercury Cell Chlor-Alkali Plants .................................
Brick and Structural Clay Products Manufacturing .............................................
Clay Ceramics Manufacturing .............................................................................
Asphalt Roofing and Processing .........................................................................
Flexible Polyurethane Foam Fabrication Operation ...........................................
Hydrochloric Acid Production ..............................................................................
Engine Test Cells/Stands ....................................................................................
Friction Products Manufacturing .........................................................................
Taconite Iron Ore Processing .............................................................................
Refractory Products Manufacturing ....................................................................
Primary Magnesium Refining ..............................................................................
Hospital Ethylene Oxide Sterilizers .....................................................................
Area Sources: Electric Arc Furnace Steelmaking Facilities ...............................
Iron and Steel Foundries Area Sources .............................................................
Gasoline Distribution Bulk Terminals, Bulk Plants, and Pipeline Facilities ........
Gasoline Dispensing Facilities ............................................................................
Polyvinyl Chloride and Copolymers Production Area Sources ..........................
Primary Copper Smelting Area Sources .............................................................
Secondary Copper Smelting Area Sources ........................................................
Primary Nonferrous Metals Area Sources—Zinc, Cadmium, and Beryllium ......
Paint Stripping and Miscellaneous Surface Coating Operations at Area
Sources.
Acrylic and Modacrylic Fibers Production Area Sources ...................................
Carbon Black Production Area Sources .............................................................
Chemical Manufacturing Area Sources: Chromium Compounds .......................
Flexible Polyurethane Foam Production and Fabrication Area Sources ...........
Lead Acid Battery Manufacturing Area Sources ................................................
Wood Preserving Area Sources .........................................................................
Clay Ceramics Manufacturing Area Sources ......................................................
Glass Manufacturing Area Sources ....................................................................
Secondary Nonferrous Metals Processing Area Sources ..................................
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
................
................
................
................
................
................
................
................
................
................
X
X
X
X
X
X
X
X
X
X
X
X
X
X
................
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
................
................
................
................
................
................
................
................
................
................
................
X
X
X
X
X
X
X
X
X
................
X
X
X
................
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
.................
.................
.................
.................
.................
.................
.................
.................
.................
.................
.................
.................
.................
.................
.................
.................
.................
.................
.................
.................
.................
.................
.................
.................
.................
.................
.................
.................
.................
.................
.................
.................
.................
.................
.................
.................
.................
.................
.................
.................
................
................
................
................
................
................
................
................
................
................
................
................
................
................
................
................
................
................
X
X
X
X
X
X
X
X
X
.................
.................
.................
.................
.................
.................
.................
.................
.................
LLLLLL ..........
MMMMMM ....
NNNNNN ......
OOOOOO .....
PPPPPP .......
QQQQQQ .....
RRRRRR ......
SSSSSS .......
TTTTTT ........
1 Arizona
Department of Environmental Quality.
County Air Quality Department.
3 Pima County Department of Environmental Quality.
4 Pinal County Air Quality Control District.
2 Maricopa
*
*
*
*
*
[FR Doc. E8–18748 Filed 8–13–08; 8:45 am]
BILLING CODE 6560–50–P
FEDERAL COMMUNICATIONS
COMMISSION
47 CFR Part 10
[PS Docket No. 07–287; FCC 08–164]
rfrederick on PROD1PC67 with RULES
Commercial Mobile Alert System
Federal Communications
Commission.
ACTION: Final rule.
AGENCY:
SUMMARY: In this document, the Federal
Communications Commission
VerDate Aug<31>2005
14:45 Aug 13, 2008
Jkt 214001
PO 00000
Frm 00028
Fmt 4700
Sfmt 4700
(Commission or FCC) complies with
section 602(c) of the Warning, Alert and
Response Network (WARN) Act by
adopting rules that require noncommercial educational (NCE) and
public broadcast television station
licensees and permittees to install
equipment and technologies that will
provide these licensees/permittees with
the ability to enable the distribution of
geo-targeted Commercial Mobile Alert
System (CMAS) alerts to participating
Commercial Mobile Service (CMS)
E:\FR\FM\14AUR1.SGM
14AUR1
]]>Agencies
[Federal Register Volume 73, Number 158 (Thursday, August 14, 2008)]
[Rules and Regulations]
[Pages 47546-47550]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: E8-18748]
-----------------------------------------------------------------------
ENVIRONMENTAL PROTECTION AGENCY
40 CFR Part 63
[EPA-R09-OAR-2008-0555; FRL-8701-7]
Delegation of National Emission Standards for Hazardous Air
Pollutants for Source Categories; State of Arizona, Arizona Department
of Environmental Quality, Pima County Department of Environmental
Quality
AGENCY: Environmental Protection Agency (EPA).
ACTION: Direct final rule.
-----------------------------------------------------------------------
SUMMARY: EPA is amending certain regulations to reflect the current
delegation status of national emission standards for hazardous air
pollutants (NESHAP) in Arizona. Several NESHAP were delegated to the
Arizona Department of Environmental Quality on June 4, 2008, and to the
Pima County Department of Environmental Quality on June 16, 2008. The
purpose of this action is to update the listing in the Code of Federal
Regulations.
DATES: This rule is effective on October 14, 2008, without further
notice, unless EPA receives adverse comments by September 15, 2008. If
we receive such comments, we will publish a timely withdrawal in the
Federal Register to notify the public that this direct final rule will
not take effect.
ADDRESSES: Submit comments, identified by docket number EPA-R09-OAR-
2008-0555, by one of the following methods:
[[Page 47547]]
1. Federal eRulemaking Portal: www.regulations.gov. Follow the on-
line instructions.
2. E-mail: steckel.andrew@epa.gov.
3. Mail or delivery: Andrew Steckel (AIR-4), U.S. Environmental
Protection Agency Region IX, 75 Hawthorne Street, San Francisco, CA
94105-3901.
Instructions: All comments will be included in the public docket
without change and may be made available online at www.regulations.gov,
including any personal information provided, unless the comment
includes Confidential Business Information (CBI) or other information
whose disclosure is restricted by statute. Information that you
consider CBI or otherwise protected should be clearly identified as
such and should not be submitted through www.regulations.gov or e-mail.
www.regulations.gov is an ``anonymous access'' system, and EPA will not
know your identity or contact information unless you provide it in the
body of your comment. If you send e-mail directly to EPA, your e-mail
address will be automatically captured and included as part of the
public comment. If EPA cannot read your comment due to technical
difficulties and cannot contact you for clarification, EPA may not be
able to consider your comment.
Docket: The index to the docket for this action is available
electronically at www.regulations.gov and in hard copy at EPA Region
IX, 75 Hawthorne Street, San Francisco, California. While all documents
in the docket are listed in the index, some information may be publicly
available only at the hard copy location (e.g., copyrighted material),
and some may not be publicly available in either location (e.g., CBI).
To inspect the hard copy materials, please schedule an appointment
during normal business hours with the contact listed in the FOR FURTHER
INFORMATION CONTACT section.
FOR FURTHER INFORMATION CONTACT: Mae Wang, EPA Region IX, (415) 947-
4124, wang.mae@epa.gov.
SUPPLEMENTARY INFORMATION: Throughout this document, ``we,'' ``us'' and
``our'' refer to EPA.
Table of Contents
I. Background
A. Delegation of NESHAP
B. ADEQ Delegations
C. PDEQ Delegations
II. EPA Action
III. Statutory and Executive Order Reviews
I. Background
A. Delegation of NESHAP
Section 112(l) of the Clean Air Act, as amended in 1990 (CAA),
authorizes EPA to delegate to state or local air pollution control
agencies the authority to implement and enforce the standards set out
in the Code of Federal Regulations, Title 40 (40 CFR), part 63,
National Emission Standards for Hazardous Air Pollutants for Source
Categories. On November 26, 1993, EPA promulgated regulations, codified
at 40 CFR part 63, Subpart E (hereinafter referred to as ``Subpart
E''), establishing procedures for EPA's approval of state rules or
programs under section 112(l) (see 58 FR 62262). Subpart E was later
amended on September 14, 2000 (see 65 FR 55810).
Any request for approval under CAA section 112(l) must meet the
approval criteria in 112(l)(5) and Subpart E. To streamline the
approval process for future applications, a state or local agency may
submit a one-time demonstration that it has adequate authorities and
resources to implement and enforce any CAA section 112 standards. If
such demonstration is approved, then the state or local agency would no
longer need to resubmit a demonstration of these same authorities and
resources for every subsequent request for delegation of CAA section
112 standards. However, EPA maintains the authority to withdraw its
approval if the State does not adequately implement or enforce an
approved rule or program.
B. ADEQ Delegations
On July 17, 1998, EPA published a direct final action delegating to
the Arizona Department of Environmental Quality (ADEQ) several NESHAP
and approving ADEQ's delegation mechanism for future standards (see 63
FR 38478). That action explained the procedure for EPA to grant
delegations to ADEQ by letter, with periodic Federal Register listings
of standards that have been delegated. On April 17, 2008, ADEQ
requested delegation of the following NESHAP contained in 40 CFR part
63:
Subpart DDDD--NESHAP: Plywood and Composite Wood Products
Subpart DDDDD--NESHAP for Industrial, Commercial, and
Institutional Boilers and Process Heaters
On June 4, 2008, EPA granted delegation to ADEQ for these NESHAP,
along with any amendments to previously-delegated NESHAP, as of July 1,
2006. Today's action is serving to notify the public of the June 4,
2008, delegations and to codify these delegations into the Code of
Federal Regulations.
C. PDEQ Delegations
On June 28, 1999, EPA published a direct final action delegating to
the Pima County Department of Environmental Quality (PDEQ) several
NESHAP and approving PDEQ's delegation mechanism for future standards
(see 64 FR 34560). That action explained the procedure for EPA to grant
delegations to PDEQ by letter, with periodic Federal Register listings
of standards that have been delegated. On May 23, 2008, PDEQ requested
delegation of the following NESHAP contained in 40 CFR part 63:
Subpart J--NESHAP for Polyvinyl Chloride and Copolymers
Production
Subpart MM--NESHAP for Chemical Recovery Combustion
Sources at Kraft, Soda, Sulfite, and Stand-Alone Semichemical Pulp
Mills
Subpart XX--National Emission Standards for Ethylene
Manufacturing Process Units: Heat Exchange Systems and Waste Operations
Subpart DDDD--NESHAP: Plywood and Composite Wood Products
Subpart WWWWW--National Emission Standards for Hospital
Ethylene Oxide Sterilizers
Subpart YYYYY--NESHAP for Area Sources: Electric Arc
Furnace Steelmaking Facilities
Subpart ZZZZZ--NESHAP for Iron and Steel Foundries Area
Sources
Subpart BBBBBB--NESHAP for Source Category: Gasoline
Distribution Bulk Terminals, Bulk Plants, and Pipeline Facilities
Subpart CCCCCC--NESHAP for Source Category: Gasoline
Dispensing Facilities
Subpart DDDDDD--NESHAP for Polyvinyl Chloride and
Copolymers Production Area Sources
Subpart EEEEEE--NESHAP for Primary Copper Smelting Area
Sources
Subpart FFFFFF--NESHAP for Secondary Copper Smelting Area
Sources
Subpart GGGGGG--NESHAP for Primary Nonferrous Metals Area
Sources--Zinc, Cadmium, and Beryllium
Subpart HHHHHH--NESHAP: Paint Stripping and Miscellaneous
Surface Coating Operations at Area Sources
Subpart LLLLLL--NESHAP for Acrylic and Modacrylic Fibers
Production Area Sources
Subpart MMMMMM--NESHAP for Carbon Black Production Area
Sources
Subpart NNNNNN--NESHAP for Chemical Manufacturing Area
Sources: Chromium Compounds
Subpart OOOOOO--NESHAP for Flexible Polyurethane Foam
Production and Fabrication Area Sources
Subpart PPPPPP--NESHAP for Lead Acid Battery Manufacturing
Area Sources
Subpart QQQQQQ--NESHAP for Wood Preserving Area Sources
[[Page 47548]]
Subpart RRRRRR--NESHAP for Clay Ceramics Manufacturing
Area Sources
Subpart SSSSSS--NESHAP for Glass Manufacturing Area
Sources
Subpart TTTTTT--NESHAP for Secondary Nonferrous Metals
Processing Area Sources
On June 16, 2008, EPA granted delegation to PDEQ for these NESHAP,
along with any amendments to previously-delegated NESHAP, as of
February 1, 2008. Today's action is serving to notify the public of the
June 16, 2008, delegations and to codify these delegations into the
Code of Federal Regulations.
II. EPA Action
Today's document serves to notify the public of the delegation of
NESHAP to ADEQ on June 4, 2008, and to PDEQ on June 16, 2008. Today's
action will codify these delegations into the Code of Federal
Regulations.
III. Statutory and Executive Order Reviews
Under the Clean Air Act, the Administrator is required to approve a
delegation request that complies with the provisions of the Act and
applicable Federal regulations. 42 U.S.C. 7412(l); 40 CFR 63.91(b).
Thus, in reviewing state delegation submissions, our role is to approve
state choices, provided that they meet the criteria of the CAA.
Accordingly, this action merely updates the list of approved
delegations in the Code of Federal Regulations and does not impose
additional requirements beyond those imposed by state law. For that
reason, this action:
Is not a ``significant regulatory action'' subject to
review by the Office of Management and Budget under Executive Order
12866 (58 FR 51735, October 4, 1993);
Does not impose an information collection burden under the
provisions of the Paperwork Reduction Act (44 U.S.C. 3501 et seq.);
Is certified as not having a significant economic impact
on a substantial number of small entities under the Regulatory
Flexibility Act (5 U.S.C. 601 et seq.);
Does not contain any unfunded mandate or significantly or
uniquely affect small governments, as described in the Unfunded
Mandates Reform Act of 1995 (Pub. L. 104-4);
Does not have Federalism implications as specified in
Executive Order 13132 (64 FR 43255, August 10, 1999);
Is not an economically significant regulatory action based
on health or safety risks subject to Executive Order 13045 (62 FR
19885, April 23, 1997);
Is not a significant regulatory action subject to
Executive Order 13211 (66 FR 28355, May 22, 2001);
Is not subject to requirements of Section 12(d) of the
National Technology Transfer and Advancement Act of 1995 (15 U.S.C. 272
note) because application of those requirements would be inconsistent
with the Clean Air Act; and
Does not provide EPA with the discretionary authority to
address, as appropriate, disproportionate human health or environmental
effects, using practicable and legally permissible methods, under
Executive Order 12898 (59 FR 7629, February 16, 1994).
In addition, this rule does not have tribal implications as
specified by Executive Order 13175 (65 FR 67249, November 9, 2000),
because the delegation submission is not approved to apply in Indian
country located in the state, and EPA notes that it will not impose
substantial direct costs on tribal governments or preempt tribal law.
The Congressional Review Act, 5 U.S.C. 801 et seq., as added by the
Small Business Regulatory Enforcement Fairness Act of 1996, generally
provides that before a rule may take effect, the agency promulgating
the rule must submit a rule report, which includes a copy of the rule,
to each House of the Congress and to the Comptroller General of the
United States. EPA will submit a report containing this action and
other required information to the U.S. Senate, the U.S. House of
Representatives, and the Comptroller General of the United States prior
to publication of the rule in the Federal Register. A major rule cannot
take effect until 60 days after it is published in the Federal
Register. This action is not a ``major rule'' as defined by 5 U.S.C.
804(2).
Under section 307(b)(1) of the Clean Air Act, petitions for
judicial review of this action must be filed in the United States Court
of Appeals for the appropriate circuit by October 14, 2008. Filing a
petition for reconsideration by the Administrator of this final rule
does not affect the finality of this action for the purposes of
judicial review nor does it extend the time within which a petition for
judicial review may be filed, and shall not postpone the effectiveness
of such rule or action. This action may not be challenged later in
proceedings to enforce its requirements (see section 307(b)(2)).
List of Subjects in 40 CFR Part 63
Environmental protection, Administrative practice and procedure,
Air pollution control, Hazardous substances, Intergovernmental
relations, Reporting and recordkeeping requirements.
Authority: This action is issued under the authority of Section
112 of the Clean Air Act, as amended, 42 U.S.C. 7412.
Dated: July 25, 2008.
Amy Zimpfer,
Acting Director, Air Division, Region IX.
0
Title 40, chapter I, part 63 of the Code of Federal Regulations is
amended as follows:
PART 63--[AMENDED]
0
1. The authority citation for part 63 continues to read as follows:
Authority: 42 U.S.C. 7401, et seq.
Subpart E--Approval of State Programs and Delegation of Federal
Authorities
0
2. Section 63.99 is amended by revising paragraph (a)(3) to read as
follows:
Sec. 63.99 Delegated Federal authorities.
(a) * * *
(3) The following table lists the specific part 63 standards that
have been delegated unchanged to the air pollution control agencies in
the State of Arizona. The (X) symbol is used to indicate each category
that has been delegated.
Delegation Status for Part 63 Standards--Arizona
----------------------------------------------------------------------------------------------------------------
Subpart Description ADEQ \1\ MCAQD \2\ PDEQ \3\ PCAQCD \4\
----------------------------------------------------------------------------------------------------------------
A............................ General Provisions............... X X X X
F............................ Synthetic Organic Chemical X X X X
Manufacturing Industry.
G............................ Synthetic Organic Chemical X X X X
Manufacturing Industry: Process
Vents, Storage Vessels, Transfer
Operations, and Wastewater.
H............................ Organic Hazardous Air Pollutants: X X X X
Equipment Leaks.
[[Page 47549]]
I............................ Organic Hazardous Air Pollutants: X X X X
Certain Processes Subject to the
Negotiated Regulation for
Equipment Leaks.
J............................ Polyvinyl Chloride and Copolymers X X X ..........
Production.
L............................ Coke Oven Batteries.............. X X X X
M............................ Perchloroethylene Dry Cleaning... X X X X
N............................ Hard and Decorative Chromium X X X X
Electroplating and Chromium
Anodizing Tanks.
O............................ Ethylene Oxide Sterilization X X X X
Facilities.
Q............................ Industrial Process Cooling Towers X X X X
R............................ Gasoline Distribution Facilities. X X X X
S............................ Pulp and Paper................... X X X ..........
T............................ Halogenated Solvent Cleaning..... X X X X
U............................ Group I Polymers and Resins...... X X X X
W............................ Epoxy Resins Production and Non- X X X X
Nylon Polyamides Production.
X............................ Secondary Lead Smelting.......... X X X X
AA........................... Phosphoric Acid Manufacturing X X X ..........
Plants.
BB........................... Phosphate Fertilizers Production X X X ..........
Plants.
CC........................... Petroleum Refineries............. X X X X
DD........................... Off-Site Waste and Recovery X X X X
Operations.
EE........................... Magnetic Tape Manufacturing X X X X
Operations.
GG........................... Aerospace Manufacturing and X X X X
Rework Facilities.
HH........................... Oil and Natural Gas Production X X X ..........
Facilities.
JJ........................... Wood Furniture Manufacturing X X X X
Operations.
KK........................... Printing and Publishing Industry. X X X X
LL........................... Primary Aluminum Reduction Plants X .......... X ..........
MM........................... Chemical Recovery Combustion X X X ..........
Sources at Kraft, Soda, Sulfite,
and Stand-Alone Semichemical
Pulp Mills.
OO........................... Tanks--Level 1................... X X X X
PP........................... Containers....................... X X X X
QQ........................... Surface Impoundments............. X X X X
RR........................... Individual Drain Systems......... X X X X
SS........................... Closed Vent Systems, Control X X X ..........
Devices, Recovery Devices and
Routing to a Fuel Gas System or
a Process.
TT........................... Equipment Leaks--Control Level 1. X X X ..........
UU........................... Equipment Leaks--Control Level 2. X X X ..........
VV........................... Oil-Water Separators and Organic- X X X X
Water Separators.
WW........................... Storage Vessels (Tanks)--Control X X X ..........
Level 2.
XX........................... Ethylene Manufacturing Process X X X ..........
Units: Heat Exchange Systems and
Waste Operations.
YY........................... Generic MACT Standards........... X X X ..........
CCC.......................... Steel Pickling................... X X X ..........
DDD.......................... Mineral Wool Production.......... X X X ..........
EEE.......................... Hazardous Waste Combustors....... X X X ..........
GGG.......................... Pharmaceuticals Production....... X X X ..........
HHH.......................... Natural Gas Transmission and X X X ..........
Storage Facilities.
III.......................... Flexible Polyurethane Foam X X X ..........
Production.
JJJ.......................... Group IV Polymers and Resins..... X X X X
LLL.......................... Portland Cement Manufacturing X X X ..........
Industry.
MMM.......................... Pesticide Active Ingredient X X X ..........
Production.
NNN.......................... Wool Fiberglass Manufacturing.... X X X ..........
OOO.......................... Manufacture of Amino/Phenolic X X X ..........
Resins.
PPP.......................... Polyether Polyols Production..... X X X ..........
QQQ.......................... Primary Copper Smelting.......... X X X ..........
RRR.......................... Secondary Aluminum Production.... X X X ..........
TTT.......................... Primary Lead Smelting............ X X X ..........
UUU.......................... Petroleum Refineries: Catalytic X X X ..........
Cracking, Catalytic Reforming,
and Sulfur Recovery Units.
VVV.......................... Publicly Owned Treatment Works... X X X ..........
XXX.......................... Ferroalloys Production........... X X X ..........
AAAA......................... Municipal Solid Waste Landfills.. X X X ..........
CCCC......................... Manufacturing of Nutritional X X X ..........
Yeast.
DDDD......................... Plywood and Composite Wood X .......... X ..........
Products.
EEEE......................... Organic Liquids Distribution (non- X X X ..........
gasoline).
FFFF......................... Miscellaneous Organic Chemical X X X ..........
Manufacturing.
GGGG......................... Solvent Extraction for Vegetable X X X ..........
Oil Production.
HHHH......................... Wet-Formed Fiberglass Mat X X X ..........
Production.
IIII......................... Surface Coating of Automobiles X X .......... ..........
and Light-Duty Trucks.
JJJJ......................... Paper and Other Web Coating...... X X X ..........
KKKK......................... Surface Coating of Metal Cans.... X X X ..........
MMMM......................... Miscellaneous Metal Parts and X X X ..........
Products.
NNNN......................... Large Appliances................. X X X ..........
OOOO......................... Printing, Coating, and Dyeing of X X X ..........
Fabrics and Other Textiles.
[[Page 47550]]
PPPP......................... Surface Coating of Plastic Parts X X .......... ..........
and Products.
QQQQ......................... Wood Building Products........... X X X ..........
RRRR......................... Surface Coating of Metal X X X ..........
Furniture.
SSSS......................... Surface Coating of Metal Coil.... X X X ..........
TTTT......................... Leather Finishing Operations..... X X X ..........
UUUU......................... Cellulose Products Manufacturing. X X X ..........
VVVV......................... Boat Manufacturing............... X X X ..........
WWWW......................... Reinforced Plastics Composites X X X ..........
Production.
XXXX......................... Tire Manufacturing............... X X X ..........
YYYY......................... Stationary Combustion Turbines... X X X ..........
ZZZZ......................... Stationary Reciprocating Internal X X .......... ..........
Combustion Engines.
AAAAA........................ Lime Manufacturing Plants........ X X X ..........
BBBBB........................ Semiconductor Manufacturing...... X X X ..........
CCCCC........................ Coke Oven: Pushing, Quenching and X X X ..........
Battery Stacks.
DDDDD........................ Industrial, Commercial, and X .......... .......... ..........
Institutional Boiler and Process
Heaters.
EEEEE........................ Iron and Steel Foundries......... X X X ..........
FFFFF........................ Integrated Iron and Steel........ X X X ..........
GGGGG........................ Site Remediation................. X X X ..........
HHHHH........................ Miscellaneous Coating X X X ..........
Manufacturing.
IIIII........................ Mercury Emissions from Mercury X X X ..........
Cell Chlor-Alkali Plants.
JJJJJ........................ Brick and Structural Clay X X X ..........
Products Manufacturing.
KKKKK........................ Clay Ceramics Manufacturing...... X X X ..........
LLLLL........................ Asphalt Roofing and Processing... X X X ..........
MMMMM........................ Flexible Polyurethane Foam X X X ..........
Fabrication Operation.
NNNNN........................ Hydrochloric Acid Production..... X X X ..........
PPPPP........................ Engine Test Cells/Stands......... X X X ..........
QQQQQ........................ Friction Products Manufacturing.. X X X ..........
RRRRR........................ Taconite Iron Ore Processing..... X X X ..........
SSSSS........................ Refractory Products Manufacturing X X X ..........
TTTTT........................ Primary Magnesium Refining....... X X X ..........
WWWWW........................ Hospital Ethylene Oxide .......... .......... X ..........
Sterilizers.
YYYYY........................ Area Sources: Electric Arc .......... .......... X ..........
Furnace Steelmaking Facilities.
ZZZZZ........................ Iron and Steel Foundries Area .......... .......... X ..........
Sources.
BBBBBB....................... Gasoline Distribution Bulk .......... .......... X ..........
Terminals, Bulk Plants, and
Pipeline Facilities.
CCCCCC....................... Gasoline Dispensing Facilities... .......... .......... X ..........
DDDDDD....................... Polyvinyl Chloride and Copolymers .......... .......... X ..........
Production Area Sources.
EEEEEE....................... Primary Copper Smelting Area .......... .......... X ..........
Sources.
FFFFFF....................... Secondary Copper Smelting Area .......... .......... X ..........
Sources.
GGGGGG....................... Primary Nonferrous Metals Area .......... .......... X ..........
Sources--Zinc, Cadmium, and
Beryllium.
HHHHHH....................... Paint Stripping and Miscellaneous .......... .......... X ..........
Surface Coating Operations at
Area Sources.
LLLLLL....................... Acrylic and Modacrylic Fibers .......... .......... X ..........
Production Area Sources.
MMMMMM....................... Carbon Black Production Area .......... .......... X ..........
Sources.
NNNNNN....................... Chemical Manufacturing Area .......... .......... X ..........
Sources: Chromium Compounds.
OOOOOO....................... Flexible Polyurethane Foam .......... .......... X ..........
Production and Fabrication Area
Sources.
PPPPPP....................... Lead Acid Battery Manufacturing .......... .......... X ..........
Area Sources.
QQQQQQ....................... Wood Preserving Area Sources..... .......... .......... X ..........
RRRRRR....................... Clay Ceramics Manufacturing Area .......... .......... X ..........
Sources.
SSSSSS....................... Glass Manufacturing Area Sources. .......... .......... X ..........
TTTTTT....................... Secondary Nonferrous Metals .......... .......... X ..........
Processing Area Sources.
----------------------------------------------------------------------------------------------------------------
\1\ Arizona Department of Environmental Quality.
\2\ Maricopa County Air Quality Department.
\3\ Pima County Department of Environmental Quality.
\4\ Pinal County Air Quality Control District.
* * * * *
[FR Doc. E8-18748 Filed 8-13-08; 8:45 am]
BILLING CODE 6560-50-P
