Airworthiness Directives; Honeywell Flight Management Systems (FMSs) Served by Honeywell NZ-2000 Navigation Computers Approved Under Technical Standard Order (TSO) TSO-C115a, and IC-800 Integrated Avionics Computers Approved Under TSOs C9c, C52a, and C115a; as Installed on Various Transport Category Airplanes, 15818-15820 [E7-5896]
Download as PDF
15818
Federal Register / Vol. 72, No. 63 / Tuesday, April 3, 2007 / Rules and Regulations
Aerospace Engineer, International Branch,
ANM–116, FAA, Transport Airplane
Directorate, 1601 Lind Avenue, SW., Renton,
Washington 98057–3356; telephone (425)
227–2677; fax (425) 227–1149. Before using
any AMOC approved in accordance with
§ 39.19 on any airplane to which the AMOC
applies, notify the appropriate principal
inspector in the FAA Flight Standards
Certificate Holding District Office.
(2) Airworthy Product: For any requirement
in this AD to obtain corrective actions from
a manufacturer or other source, use these
actions if they are FAA-approved. Corrective
actions are considered FAA-approved if they
are approved by the State of Design Authority
(or their delegated agent). You are required
to assure the product is airworthy before it
is returned to service.
(3) Reporting Requirements: For any
reporting requirement in this AD, under the
provisions of the Paperwork Reduction Act,
the Office of Management and Budget (OMB)
has approved the information collection
requirements and has assigned OMB Control
Number 2120–0056.
Related Information
(h) Refer to MCAI Israeli Airworthiness
Directive 28–07–02–03, dated February 11,
2007, and Gulfstream Alert Service Bulletin
200–28A–315, dated February 5, 2007, for
related information.
Material Incorporated by Reference
(i) You must use Gulfstream Alert Service
Bulletin 200–28A–315, dated February 5,
2007, to do the actions required by this AD,
unless the AD specifies otherwise.
(1) The Director of the Federal Register
approved the incorporation by reference of
this service information under 5 U.S.C.
552(a) and 1 CFR part 51.
(2) For service information identified in
this AD, contact Gulfstream Aerospace
Corporation, P.O. Box 2206, Mail Station D–
25, Savannah, Georgia 31402–2206.
(3) You may review copies at the FAA,
Transport Airplane Directorate, 1601 Lind
Avenue, SW., Renton, Washington; or at the
National Archives and Records
Administration (NARA). For information on
the availability of this material at NARA, call
(202) 741–6030, or go to: https://
www.archives.gov/federal-register/cfr/ibrlocations.html.
Issued in Renton, Washington, on March
23, 2007.
Ali Bahrami,
Manager, Transport Airplane Directorate,
Aircraft Certification Service.
[FR Doc. E7–5898 Filed 4–2–07; 8:45 am]
rwilkins on PROD1PC63 with RULES
BILLING CODE 4910–13–P
VerDate Aug<31>2005
16:32 Apr 02, 2007
Jkt 211001
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA–2007–27735; Directorate
Identifier 2007–NM–027–AD; Amendment
39–15009; AD 2007–07–12]
RIN 2120–AA64
Airworthiness Directives; Honeywell
Flight Management Systems (FMSs)
Served by Honeywell NZ–2000
Navigation Computers Approved
Under Technical Standard Order (TSO)
TSO–C115a, and IC–800 Integrated
Avionics Computers Approved Under
TSOs C9c, C52a, and C115a; as
Installed on Various Transport
Category Airplanes
Federal Aviation
Administration (FAA), Department of
Transportation (DOT).
ACTION: Final rule; request for
comments.
AGENCY:
The FAA is adopting a new
airworthiness directive (AD) for all
Honeywell FMSs served by Honeywell
NZ–2000 navigation computers and IC–
800 integrated avionics computers. This
AD requires identifying affected
computers by part number and software
modification level and revising the
Limitations section of applicable
airplane flight manuals to provide
procedures for retaining optimum
position determination and intended
navigation. This AD results from reports
of in-flight unannunciated shifts of
computed position in airplanes with the
subject flight management system (FMS)
computers. We are issuing this AD to
prevent a shift in the FMS computed
position, which could result in
uncommanded deviations from the
intended flight path of the airplane and,
if those deviations are undetected by the
flight crew, compromised terrain/traffic
avoidance.
DATES: This AD becomes effective April
18, 2007.
The Director of the Federal Register
approved the incorporation by reference
of certain publications listed in the AD
as of April 18, 2007.
We must receive comments on this
AD by June 4, 2007.
ADDRESSES: Use one of the following
addresses to submit comments on this
AD.
• DOT Docket Web site: Go to
https://dms.dot.gov and follow the
instructions for sending your comments
electronically.
• Government-wide rulemaking Web
site: Go to https://www.regulations.gov
SUMMARY:
PO 00000
Frm 00014
Fmt 4700
Sfmt 4700
and follow the instructions for sending
your comments electronically.
• Mail: Docket Management Facility;
U.S. Department of Transportation, 400
Seventh Street, SW., Nassif Building,
Room PL–401, Washington, DC 20590.
• Fax: (202) 493–2251.
• Hand Delivery: Room PL–401 on
the plaza level of the Nassif Building,
400 Seventh Street, SW., Washington,
DC, between 9 a.m. and 5 p.m., Monday
through Friday, except Federal holidays.
Contact Honeywell, P.O. Box 21111,
Phoenix, AZ 85036–1111, for service
information identified in this AD.
FOR FURTHER INFORMATION CONTACT: Joe
Brownlee, Flight Test Pilot, Flight Test
Branch, ANM–160L, FAA, Los Angeles
Aircraft Certification Office, 3960
Paramount Boulevard, Lakewood,
California 90712–4137; telephone (562)
627–5365; fax (562) 627–5210.
SUPPLEMENTARY INFORMATION:
Discussion
We have received reports of in-flight
unannunciated shifts of computed
position in airplanes with Honeywell
NZ–2000 navigation and IC–800
integrated avionics computers serving
Honeywell Flight Management Systems
(FMSs). The computed position shift,
attributed to a software design error
induced during a previous software
modification, occurs when the number
of inertial reference units (IRUs)
supplying data to the FMS degrades
from 3 to 2 or from 2 to 1, or increases
from 2 to 3 or from 1 to 2. If the FMS
system is coupled to an autopilot or
flight director system, this shift in the
FMS computed position could result in
uncommanded deviations from the
intended flight path of the airplane and,
if those deviations are undetected by the
flight crew, compromised terrain/traffic
avoidance.
Relevant Service Information
We have reviewed Honeywell
Technical Newsletter A23–6111–008,
Revision 001, dated February 22, 2007.
This technical newsletter describes
procedures for determining affected
FMS computers receiving position
information from multiple IRUs by
identifying the part number and
software modification level of the NZ–
2000 navigation and IC–800 integrated
avionics computers serving these Flight
Management Systems. For airplanes
with affected part numbers and software
modification levels, the newsletter also
describes revising the Limitations
section of the applicable airplane flight
manuals (AFMs) to provide procedures
for deselecting all but one IRS to each
FMS on every power-up cycle. The
E:\FR\FM\03APR1.SGM
03APR1
Federal Register / Vol. 72, No. 63 / Tuesday, April 3, 2007 / Rules and Regulations
AFM revision is provided as Appendix
A in the newsletter.
FAA’s Determination and Requirements
of This AD
The unsafe condition described
previously is likely to exist or develop
on other airplanes of the same type
design. For this reason, we are issuing
this AD to prevent errors in airplane
position displays and consequent
deviation from the intended flight path.
This AD requires accomplishing the
actions specified in the Technical
Newsletter described previously.
Interim Action
We consider this AD interim action.
The manufacturer is currently
developing a modification that will
address the unsafe condition identified
in this AD. Once this modification is
developed, approved, and available, we
might consider additional rulemaking.
FAA’s Determination of the Effective
Date
Since an unsafe condition exists that
requires the immediate adoption of this
AD, we have found that notice and
opportunity for public comment before
issuing this AD are impracticable, and
that good cause exists to make this AD
effective in less than 30 days.
Comments Invited
This AD is a final rule that involves
requirements that affect flight safety and
was not preceded by notice and an
opportunity for public comment;
however, we invite you to submit any
relevant written data, views, or
arguments regarding this AD. Send your
comments to an address listed in the
ADDRESSES section. Include ‘‘Docket No.
FAA–2007–27735; Directorate Identifier
2007–NM–027–AD’’ at the beginning of
your comments. We specifically invite
comments on the overall regulatory,
economic, environmental, and energy
aspects of the AD that might suggest a
need to modify it.
We will post all comments we
receive, without change, to https://
dms.dot.gov, including any personal
information you provide. We will also
post a report summarizing each
substantive verbal contact with FAA
personnel concerning this AD. Using the
search function of that web site, anyone
can find and read the comments in any
of our dockets, including the name of
the individual who sent the comment
(or signed the comment on behalf of an
association, business, labor union, etc.).
You may review the DOT’s complete
Privacy Act Statement in the Federal
Register published on April 11, 2000
(65 FR 19477–78), or you may visit
https://dms.dot.gov.
Examining the Docket
You may examine the AD docket on
the Internet at https://dms.dot.gov, or in
person at the Docket Management
Facility office between 9 a.m. and 5
p.m., Monday through Friday, except
Federal holidays. The Docket
Management Facility office (telephone
(800) 647–5227) is located on the plaza
level of the Nassif Building at the DOT
street address stated in the ADDRESSES
section. Comments will be available in
the AD docket shortly after the Docket
Management System receives them.
Authority for This Rulemaking
Title 49 of the United States Code
specifies the FAA’s authority to issue
rules on aviation safety. Subtitle I,
Section 106, describes the authority of
the FAA Administrator. Subtitle VII,
Aviation Programs, describes in more
detail the scope of the Agency’s
authority.
We are issuing this rulemaking under
the authority described in Subtitle VII,
Part A, Subpart III, Section 44701,
‘‘General requirements.’’ Under that
section, Congress charges the FAA with
promoting safe flight of civil aircraft in
air commerce by prescribing regulations
for practices, methods, and procedures
the Administrator finds necessary for
safety in air commerce. This regulation
is within the scope of that authority
because it addresses an unsafe condition
that is likely to exist or develop on
products identified in this rulemaking
action.
15819
For the reasons discussed above, I
certify that the regulation:
1. Is not a ‘‘significant regulatory
action’’ under Executive Order 12866;
2. Is not a ‘‘significant rule’’ under the
DOT Regulatory Policies and Procedures
(44 FR 11034, February 26, 1979); and
3. Will not have a significant
economic impact, positive or negative,
on a substantial number of small entities
under the criteria of the Regulatory
Flexibility Act.
We prepared a regulatory evaluation
of the estimated costs to comply with
this AD and placed it in the AD docket.
See the ADDRESSES section for a location
to examine the regulatory evaluation.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation
safety, Incorporation by reference,
Safety.
Adoption of the Amendment
Accordingly, under the authority
delegated to me by the Administrator,
the FAA amends 14 CFR part 39 as
follows:
I
PART 39—AIRWORTHINESS
DIRECTIVES
1. The authority citation for part 39
continues to read as follows:
I
Authority: 49 U.S.C. 106(g), 40113, 44701.
§ 39.13
[Amended]
2. The Federal Aviation
Administration (FAA) amends § 39.13
by adding the following new
airworthiness directive (AD):
I
2007–07–12 Honeywell, Inc.: Amendment
39–15009. Docket No. FAA–2007–27735;
Directorate Identifier 2007–NM–027–AD.
Effective Date
(a) This AD becomes effective April 18,
2007.
Regulatory Findings
Affected ADs
(b) None.
We have determined that this AD will
not have federalism implications under
Executive Order 13132. This AD will
not have a substantial direct effect on
the States, on the relationship between
the national government and the States,
or on the distribution of power and
responsibilities among the various
levels of government.
Applicability
(c) This AD applies to all Honeywell NZ–
2000 navigation computers approved under
Technical Standard Order (TSO) TSO–C115a,
and IC–800 integrated avionics computers
approved under TSOs C9c, C52a, and C115a;
as installed on transport category airplanes,
certificated in any category, including but not
limited to the airplanes identified in Table 1
of this AD.
rwilkins on PROD1PC63 with RULES
TABLE 1.—KNOWN AFFECTED AIRPLANES
Manufacturer
Model
Bombardier, Inc ........................................................................................
Dassault Aviation ......................................................................................
Gulfstream Aerospace Corporation ..........................................................
Lockheed ..................................................................................................
VerDate Aug<31>2005
16:32 Apr 02, 2007
Jkt 211001
PO 00000
Frm 00015
Fmt 4700
CL–600–2B16 (CL–601–3A, CL–601–3R, and CL–604) airplanes.
Mystere-Falcon 900 airplanes.
G–1159A, G–IV, and GV airplanes.
382G series airplanes.
Sfmt 4700
E:\FR\FM\03APR1.SGM
03APR1
15820
Federal Register / Vol. 72, No. 63 / Tuesday, April 3, 2007 / Rules and Regulations
TABLE 1.—KNOWN AFFECTED AIRPLANES—Continued
Manufacturer
Model
Raytheon Aircraft Company .....................................................................
Unsafe Condition
(d) This AD results from reports of in-flight
unannunciated shifts of computed position
in airplanes with the subject flight
management system (FMS) computers
identified in paragraph (c) of this AD. We are
issuing this AD to prevent a shift in the FMS
computed position, which could result in
uncommanded deviations from the intended
flight path of the airplane and, if those
deviations are undetected by the flight crew,
compromised terrain/traffic avoidance.
Compliance
(e) You are responsible for having the
actions required by this AD performed within
the compliance times specified, unless the
actions have already been done.
Identification of Part Number/Modification
Level
(f) Within 14 days after the effective date
of this AD: Determine if the installed NZ–
2000 navigation computers and IC–800
integrated avionics computers serving FMSs
have computer part numbers and software
modification levels identified in Honeywell
Technical Newsletter A23–6111–008,
Revision 001, dated February 22, 2007. For
purposes of this AD, airplanes with FMS
computers having a part number and
software modification level identified in the
newsletter are ‘‘affected airplanes.’’
Revision of Airplane Flight Manual (AFM)
(g) For any affected airplane: Within 14
days after the effective date of this AD, revise
the Limitations section of the applicable
AFM to incorporate the information included
in Appendix A of Honeywell Technical
Newsletter A23–6111–008, Revision 001,
dated February 22, 2007. This may be done
by inserting a copy of Appendix A of the
newsletter into the AFM.
rwilkins on PROD1PC63 with RULES
Alternative Methods of Compliance
(AMOCs)
(h)(1) The Manager, Los Angeles Aircraft
Certification Office (ACO), FAA, has the
authority to approve AMOCs for this AD, if
requested in accordance with the procedures
found in 14 CFR 39.19.
(2) To request a different method of
compliance or a different compliance time
for this AD, follow the procedures in 14 CFR
39.19. Before using any approved AMOC on
any airplane to which the AMOC applies,
notify your appropriate principal inspector
(PI) in the FAA Flight Standards District
Office (FSDO), or lacking a PI, your local
FSDO.
Material Incorporated by Reference
(i) You must use Honeywell Technical
Newsletter A23–6111–008, Revision 001,
dated February 22, 2007, to perform the
actions that are required by this AD, unless
the AD specifies otherwise. The Director of
VerDate Aug<31>2005
16:32 Apr 02, 2007
Jkt 211001
BAe.125 Series 800A (including C–29A and U–125) airplanes.
Hawker 800XP and 1000 airplanes.
the Federal Register approved the
incorporation by reference of this document
in accordance with 5 U.S.C. 552(a) and 1 CFR
part 51. Contact Honeywell, P.O. Box 21111,
Phoenix, AZ 85036–1111, for a copy of this
service information. You may review copies
at the FAA, Transport Airplane Directorate,
1601 Lind Avenue, SW., Renton,
Washington; or at the National Archives and
Records Administration (NARA). For
information on the availability of this
material at NARA, call 202–741–6030, or go
to: https://www.archives.gov/federal-register/
cfr/ibr-locations.html.
Issued in Renton, Washington, on March
23, 2007.
Ali Bahrami,
Manager, Transport Airplane Directorate,
Aircraft Certification Service.
[FR Doc. E7–5896 Filed 4–2–07; 8:45 am]
BILLING CODE 4910–13–P
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA–2007–27736; Directorate
Identifier 2007–NM–001–AD; Amendment
39–15010; AD 2007–07–05]
RIN 2120–AA64
Airworthiness Directives; Boeing
Model 777 Airplanes
Federal Aviation
Administration (FAA), Department of
Transportation (DOT).
ACTION: Final rule; request for
comments.
AGENCY:
SUMMARY: The FAA is adopting a new
airworthiness directive (AD) for all
Boeing Model 777 airplanes. This AD
requires a one-time inspection to
determine the part number of the left
and right air supply and cabin pressure
controllers (ASCPCs) and installation of
new ASCPC software if necessary. This
AD results from a report of an ASCPC
failure during flight. We are issuing this
AD to prevent an ASCPC failure that
could stop airflow into the airplane,
inhibit the cabin altitude warning
message, and cause an incorrect display
of cabin altitude. These failures could
result in depressurization of the
airplane without warning.
DATES: This AD becomes effective April
18, 2007.
PO 00000
Frm 00016
Fmt 4700
Sfmt 4700
The Director of the Federal Register
approved the incorporation by reference
of a certain publication listed in the AD
as of April 18, 2007.
We must receive comments on this
AD by June 4, 2007.
ADDRESSES: Use one of the following
addresses to submit comments on this
AD.
• DOT Docket Web site: Go to
https://dms.dot.gov and follow the
instructions for sending your comments
electronically.
• Government-wide rulemaking Web
site: Go to https://www.regulations.gov
and follow the instructions for sending
your comments electronically.
• Mail: Docket Management Facility;
U.S. Department of Transportation, 400
Seventh Street SW., Nassif Building,
room PL–401, Washington, DC 20590.
• Fax: (202) 493–2251.
• Hand Delivery: Room PL–401 on
the plaza level of the Nassif Building,
400 Seventh Street SW., Washington,
DC, between 9:00 a.m. and 5:00 p.m.,
Monday through Friday, except Federal
holidays.
Contact Boeing Commercial
Airplanes, P.O. Box 3707, Seattle,
Washington 98124–2207, for service
information identified in this AD.
FOR FURTHER INFORMATION CONTACT:
David Webber, Aerospace Engineer,
Cabin Safety and Environmental
Systems Branch, ANM–150S, FAA,
Seattle Aircraft Certification Office,
1601 Lind Avenue, SW., Renton,
Washington 98057–3356; telephone
(425) 917–6451; fax (425) 917–6590.
SUPPLEMENTARY INFORMATION:
Discussion
We have received a report indicating
that the left air supply and cabin
pressure controller (ASCPC) incorrectly
shut off the right air conditioning pack
and the left bleed, and erratically
opened and closed the isolation valves,
on a Model 777 airplane during flight.
This resulted in periods of loss of
conditioned inflow to the cabin and
flight deck. The flightcrew descended
the airplane to 10,000 feet and returned
to the airport. Investigation into this
event revealed that the actions of the
ASCPC resulted from a solder defect in
the Aeronautical Radio, Inc. (ARINC)
629 hardware that occurred during
manufacturing. The manufacturing error
E:\FR\FM\03APR1.SGM
03APR1
Agencies
[Federal Register Volume 72, Number 63 (Tuesday, April 3, 2007)]
[Rules and Regulations]
[Pages 15818-15820]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: E7-5896]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2007-27735; Directorate Identifier 2007-NM-027-AD;
Amendment 39-15009; AD 2007-07-12]
RIN 2120-AA64
Airworthiness Directives; Honeywell Flight Management Systems
(FMSs) Served by Honeywell NZ-2000 Navigation Computers Approved Under
Technical Standard Order (TSO) TSO-C115a, and IC-800 Integrated
Avionics Computers Approved Under TSOs C9c, C52a, and C115a; as
Installed on Various Transport Category Airplanes
AGENCY: Federal Aviation Administration (FAA), Department of
Transportation (DOT).
ACTION: Final rule; request for comments.
-----------------------------------------------------------------------
SUMMARY: The FAA is adopting a new airworthiness directive (AD) for all
Honeywell FMSs served by Honeywell NZ-2000 navigation computers and IC-
800 integrated avionics computers. This AD requires identifying
affected computers by part number and software modification level and
revising the Limitations section of applicable airplane flight manuals
to provide procedures for retaining optimum position determination and
intended navigation. This AD results from reports of in-flight
unannunciated shifts of computed position in airplanes with the subject
flight management system (FMS) computers. We are issuing this AD to
prevent a shift in the FMS computed position, which could result in
uncommanded deviations from the intended flight path of the airplane
and, if those deviations are undetected by the flight crew, compromised
terrain/traffic avoidance.
DATES: This AD becomes effective April 18, 2007.
The Director of the Federal Register approved the incorporation by
reference of certain publications listed in the AD as of April 18,
2007.
We must receive comments on this AD by June 4, 2007.
ADDRESSES: Use one of the following addresses to submit comments on
this AD.
DOT Docket Web site: Go to https://dms.dot.gov and follow
the instructions for sending your comments electronically.
Government-wide rulemaking Web site: Go to https://
www.regulations.gov and follow the instructions for sending your
comments electronically.
Mail: Docket Management Facility; U.S. Department of
Transportation, 400 Seventh Street, SW., Nassif Building, Room PL-401,
Washington, DC 20590.
Fax: (202) 493-2251.
Hand Delivery: Room PL-401 on the plaza level of the
Nassif Building, 400 Seventh Street, SW., Washington, DC, between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
Contact Honeywell, P.O. Box 21111, Phoenix, AZ 85036-1111, for
service information identified in this AD.
FOR FURTHER INFORMATION CONTACT: Joe Brownlee, Flight Test Pilot,
Flight Test Branch, ANM-160L, FAA, Los Angeles Aircraft Certification
Office, 3960 Paramount Boulevard, Lakewood, California 90712-4137;
telephone (562) 627-5365; fax (562) 627-5210.
SUPPLEMENTARY INFORMATION:
Discussion
We have received reports of in-flight unannunciated shifts of
computed position in airplanes with Honeywell NZ-2000 navigation and
IC-800 integrated avionics computers serving Honeywell Flight
Management Systems (FMSs). The computed position shift, attributed to a
software design error induced during a previous software modification,
occurs when the number of inertial reference units (IRUs) supplying
data to the FMS degrades from 3 to 2 or from 2 to 1, or increases from
2 to 3 or from 1 to 2. If the FMS system is coupled to an autopilot or
flight director system, this shift in the FMS computed position could
result in uncommanded deviations from the intended flight path of the
airplane and, if those deviations are undetected by the flight crew,
compromised terrain/traffic avoidance.
Relevant Service Information
We have reviewed Honeywell Technical Newsletter A23-6111-008,
Revision 001, dated February 22, 2007. This technical newsletter
describes procedures for determining affected FMS computers receiving
position information from multiple IRUs by identifying the part number
and software modification level of the NZ-2000 navigation and IC-800
integrated avionics computers serving these Flight Management Systems.
For airplanes with affected part numbers and software modification
levels, the newsletter also describes revising the Limitations section
of the applicable airplane flight manuals (AFMs) to provide procedures
for deselecting all but one IRS to each FMS on every power-up cycle.
The
[[Page 15819]]
AFM revision is provided as Appendix A in the newsletter.
FAA's Determination and Requirements of This AD
The unsafe condition described previously is likely to exist or
develop on other airplanes of the same type design. For this reason, we
are issuing this AD to prevent errors in airplane position displays and
consequent deviation from the intended flight path. This AD requires
accomplishing the actions specified in the Technical Newsletter
described previously.
Interim Action
We consider this AD interim action. The manufacturer is currently
developing a modification that will address the unsafe condition
identified in this AD. Once this modification is developed, approved,
and available, we might consider additional rulemaking.
FAA's Determination of the Effective Date
Since an unsafe condition exists that requires the immediate
adoption of this AD, we have found that notice and opportunity for
public comment before issuing this AD are impracticable, and that good
cause exists to make this AD effective in less than 30 days.
Comments Invited
This AD is a final rule that involves requirements that affect
flight safety and was not preceded by notice and an opportunity for
public comment; however, we invite you to submit any relevant written
data, views, or arguments regarding this AD. Send your comments to an
address listed in the ADDRESSES section. Include ``Docket No. FAA-2007-
27735; Directorate Identifier 2007-NM-027-AD'' at the beginning of your
comments. We specifically invite comments on the overall regulatory,
economic, environmental, and energy aspects of the AD that might
suggest a need to modify it.
We will post all comments we receive, without change, to https://
dms.dot.gov, including any personal information you provide. We will
also post a report summarizing each substantive verbal contact with FAA
personnel concerning this AD. Using the search function of that web
site, anyone can find and read the comments in any of our dockets,
including the name of the individual who sent the comment (or signed
the comment on behalf of an association, business, labor union, etc.).
You may review the DOT's complete Privacy Act Statement in the Federal
Register published on April 11, 2000 (65 FR 19477-78), or you may visit
https://dms.dot.gov.
Examining the Docket
You may examine the AD docket on the Internet at https://
dms.dot.gov, or in person at the Docket Management Facility office
between 9 a.m. and 5 p.m., Monday through Friday, except Federal
holidays. The Docket Management Facility office (telephone (800) 647-
5227) is located on the plaza level of the Nassif Building at the DOT
street address stated in the ADDRESSES section. Comments will be
available in the AD docket shortly after the Docket Management System
receives them.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, Section 106, describes the
authority of the FAA Administrator. Subtitle VII, Aviation Programs,
describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701, ``General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
We have determined that this AD will not have federalism
implications under Executive Order 13132. This AD will not have a
substantial direct effect on the States, on the relationship between
the national government and the States, or on the distribution of power
and responsibilities among the various levels of government.
For the reasons discussed above, I certify that the regulation:
1. Is not a ``significant regulatory action'' under Executive Order
12866;
2. Is not a ``significant rule'' under the DOT Regulatory Policies
and Procedures (44 FR 11034, February 26, 1979); and
3. Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to
comply with this AD and placed it in the AD docket. See the ADDRESSES
section for a location to examine the regulatory evaluation.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
Adoption of the Amendment
0
Accordingly, under the authority delegated to me by the Administrator,
the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The Federal Aviation Administration (FAA) amends Sec. 39.13 by
adding the following new airworthiness directive (AD):
2007-07-12 Honeywell, Inc.: Amendment 39-15009. Docket No. FAA-2007-
27735; Directorate Identifier 2007-NM-027-AD.
Effective Date
(a) This AD becomes effective April 18, 2007.
Affected ADs
(b) None.
Applicability
(c) This AD applies to all Honeywell NZ-2000 navigation
computers approved under Technical Standard Order (TSO) TSO-C115a,
and IC-800 integrated avionics computers approved under TSOs C9c,
C52a, and C115a; as installed on transport category airplanes,
certificated in any category, including but not limited to the
airplanes identified in Table 1 of this AD.
Table 1.--Known Affected Airplanes
------------------------------------------------------------------------
Manufacturer Model
------------------------------------------------------------------------
Bombardier, Inc........................ CL-600-2B16 (CL-601-3A, CL-601-
3R, and CL-604) airplanes.
Dassault Aviation...................... Mystere-Falcon 900 airplanes.
Gulfstream Aerospace Corporation....... G-1159A, G-IV, and GV
airplanes.
Lockheed............................... 382G series airplanes.
[[Page 15820]]
Raytheon Aircraft Company.............. BAe.125 Series 800A (including
C-29A and U-125) airplanes.
Hawker 800XP and 1000
airplanes.
------------------------------------------------------------------------
Unsafe Condition
(d) This AD results from reports of in-flight unannunciated
shifts of computed position in airplanes with the subject flight
management system (FMS) computers identified in paragraph (c) of
this AD. We are issuing this AD to prevent a shift in the FMS
computed position, which could result in uncommanded deviations from
the intended flight path of the airplane and, if those deviations
are undetected by the flight crew, compromised terrain/traffic
avoidance.
Compliance
(e) You are responsible for having the actions required by this
AD performed within the compliance times specified, unless the
actions have already been done.
Identification of Part Number/Modification Level
(f) Within 14 days after the effective date of this AD:
Determine if the installed NZ-2000 navigation computers and IC-800
integrated avionics computers serving FMSs have computer part
numbers and software modification levels identified in Honeywell
Technical Newsletter A23-6111-008, Revision 001, dated February 22,
2007. For purposes of this AD, airplanes with FMS computers having a
part number and software modification level identified in the
newsletter are ``affected airplanes.''
Revision of Airplane Flight Manual (AFM)
(g) For any affected airplane: Within 14 days after the
effective date of this AD, revise the Limitations section of the
applicable AFM to incorporate the information included in Appendix A
of Honeywell Technical Newsletter A23-6111-008, Revision 001, dated
February 22, 2007. This may be done by inserting a copy of Appendix
A of the newsletter into the AFM.
Alternative Methods of Compliance (AMOCs)
(h)(1) The Manager, Los Angeles Aircraft Certification Office
(ACO), FAA, has the authority to approve AMOCs for this AD, if
requested in accordance with the procedures found in 14 CFR 39.19.
(2) To request a different method of compliance or a different
compliance time for this AD, follow the procedures in 14 CFR 39.19.
Before using any approved AMOC on any airplane to which the AMOC
applies, notify your appropriate principal inspector (PI) in the FAA
Flight Standards District Office (FSDO), or lacking a PI, your local
FSDO.
Material Incorporated by Reference
(i) You must use Honeywell Technical Newsletter A23-6111-008,
Revision 001, dated February 22, 2007, to perform the actions that
are required by this AD, unless the AD specifies otherwise. The
Director of the Federal Register approved the incorporation by
reference of this document in accordance with 5 U.S.C. 552(a) and 1
CFR part 51. Contact Honeywell, P.O. Box 21111, Phoenix, AZ 85036-
1111, for a copy of this service information. You may review copies
at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW.,
Renton, Washington; or at the National Archives and Records
Administration (NARA). For information on the availability of this
material at NARA, call 202-741-6030, or go to: https://
www.archives.gov/federal-register/cfr/ibr-locations.html.
Issued in Renton, Washington, on March 23, 2007.
Ali Bahrami,
Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. E7-5896 Filed 4-2-07; 8:45 am]
BILLING CODE 4910-13-P