Airworthiness Directives; Airbus Model A310 Airplanes and Model A300 B4-600, B4-600R, and F4-600R Series Airplanes, and Model C4-605R Variant F airplanes (Collectively Called A300-600 Series Airplanes), 5362-5364 [E7-1872]

Download as PDF 5362 Federal Register / Vol. 72, No. 24 / Tuesday, February 6, 2007 / Proposed Rules Actions Compliance Procedures (1) Do the following: (i) Install access holes for visual inspection of the part number (P/N) 30012–7 horizontal stabilizer brace tube assembly. (ii) Conduct a detailed visual inspection for cracks in the P/N 30012–7 horizontal stabilizer brace tube assembly. (2) Replace the P/N 30012–7 horizontal stabilizer brace tube assembly with a new design P/N 30766–1 horizontal stabilizer brace tube assembly. Install the access holes and do the initial inspection upon accumulating 2,000 hours time-in-service (TIS) or within the next 60 days after the effective date of this AD, whichever occurs later. Repetitively inspect thereafter at intervals not to exceed 100 hours TIS. Replacement of the P/N 30012–7 horizontal stabilizer brace tube assembly with a new design P/N 30766–1 horizontal stabilizer brace tube assembly following paragraph (e)(2) of this AD is terminating action for the repetitive inspection requirement of this AD. Follow Snow Engineering Co. Service Letter #235, dated August 25, 2004, revised October 23, 2006. Before further flight after any inspection required by paragraph (e)(1) of this AD where cracks are found. The installation of a new design P/N 30766–1 horizontal stabilizer brace tube assembly is terminating action for the repetitive inspection requirement of this AD. (3) Do not install any P/N 30012–7 horizontal stabilizer brace tube assembly. As of the effective date of this AD ........................................................ Follow Snow Engineering Co. Service Letter #129A, dated August 7, 2004, revised November 15, 2005; Snow Engineering Co. Service Letter #235, dated August 25, 2004, revised October 23, 2006; and Snow Engineering Co. Drill Template—602, Drawing Number SL129–602, dated August 2, 2004. Not Applicable. Alternative Methods of Compliance (AMOCs) DEPARTMENT OF TRANSPORTATION (f) The Manager, Fort Worth Airplane Certification Office, FAA, ATTN: Andrew McAnaul, Aerospace Engineer, ASW–150 (c/ o MIDO–43), 10100 Reunion Place, Suite 650, San Antonio, Texas 78216; telephone: (210) 308–3365; fax: (210) 308–3370, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Federal Aviation Administration Related Information (g) To get copies of the service information referenced in this AD, contact Air Tractor Inc., P.O. Box 485, Olney, Texas 76374; telephone: (940) 564–5616; fax: (940) 564– 5612. To view the AD docket, go to the Docket Management Facility; U.S. Department of Transportation, 400 Seventh Street, SW., Nassif Building, Room PL–401, Washington, DC, or on the Internet at https:// dms.dot.gov. The docket number is Docket No. FAA–2006–26775; Directorate Identifier 2007–CE–01–AD. Issued in Kansas City, Missouri, on January 31, 2007. Margaret Kline, Acting Manager, Small Airplane Directorate, Aircraft Certification Service. [FR Doc. E7–1874 Filed 2–5–07; 8:45 am] rmajette on PROD1PC67 with PROPOSALS BILLING CODE 4910–13–P VerDate Aug<31>2005 14:49 Feb 05, 2007 Jkt 211001 14 CFR Part 39 [Docket No. FAA–2007–27154; Directorate Identifier 2006–NM–139–AD] RIN 2120–AA64 Airworthiness Directives; Airbus Model A310 Airplanes and Model A300 B4– 600, B4–600R, and F4–600R Series Airplanes, and Model C4–605R Variant F airplanes (Collectively Called A300– 600 Series Airplanes) Federal Aviation Administration (FAA), Department of Transportation (DOT). ACTION: Notice of proposed rulemaking (NPRM). AGENCY: SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) for all Airbus Model A310 airplanes and Model A300–600 series airplanes. This proposed AD would require revising the Airworthiness Limitations section of the Instructions for Continued Airworthiness by incorporating new and revised certification maintenance requirements. This proposed AD results from the manufacturer determining that additional and revised certification maintenance requirements are necessary in order to ensure continued operational safety of the affected airplanes. We are proposing this AD to prevent safetysignificant latent failures that would, in combination with one or more other specific failures or events, result in a hazardous or catastrophic failure condition of avionics, hydraulic PO 00000 Frm 00015 Fmt 4702 Sfmt 4702 systems, fire detection systems, fuel systems, or other critical systems. DATES: We must receive comments on this proposed AD by March 8, 2007. ADDRESSES: Use one of the following addresses to submit comments on this proposed AD. • DOT Docket Web site: Go to https://dms.dot.gov and follow the instructions for sending your comments electronically. • Government-wide rulemaking Web site: Go to https://www.regulations.gov and follow the instructions for sending your comments electronically. • Mail: Docket Management Facility, U.S. Department of Transportation, 400 Seventh Street, SW., Nassif Building, room PL–401, Washington, DC 20590. • Fax: (202) 493–2251. • Hand Delivery: Room PL–401 on the plaza level of the Nassif Building, 400 Seventh Street, SW., Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. Contact Airbus, 1 Rond Point Maurice Bellonte, 31707 Blagnac Cedex, France, for service information identified in this proposed AD. FOR FURTHER INFORMATION CONTACT: Tom Stafford, Aerospace Engineer, International Branch, ANM–116, FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington 98057–3356; telephone (425) 227–1622; fax (425) 227–1149. SUPPLEMENTARY INFORMATION: Comments Invited We invite you to submit any relevant written data, views, or arguments regarding this proposed AD. Send your comments to an address listed in the ADDRESSES section. Include the docket E:\FR\FM\06FEP1.SGM 06FEP1 5363 Federal Register / Vol. 72, No. 24 / Tuesday, February 6, 2007 / Proposed Rules number ‘‘FAA–2007–27154; Directorate Identifier 2006-NM–139–AD’’ at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of the proposed AD. We will consider all comments received by the closing date and may amend the proposed AD in light of those comments. We will post all comments we receive, without change, to https:// dms.dot.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact with FAA personnel concerning this proposed AD. Using the search function of that Web site, anyone can find and read the comments in any of our dockets, including the name of the individual who sent the comment (or signed the comment on behalf of an association, business, labor union, etc.). You may review the DOT’s complete Privacy Act Statement in the Federal Register published on April 11, 2000 (65 FR 19477–78), or you may visit https:// dms.dot.gov. Examining the Docket You may examine the AD docket on the Internet at https://dms.dot.gov, or in person at the Docket Management Facility office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The Docket Management Facility office (telephone (800) 647–5227) is located on the plaza level of the Nassif Building at the DOT street address stated in the ADDRESSES section. Comments will be available in the AD docket shortly after the Docket Management System receives them. Discussion ´ ´ The Direction Generale de l’Aviation Civile (DGAC), which is the airworthiness authority for France, notified us that Part 3, ‘‘Certification Maintenance Requirements (CMR)’’ of the Airworthiness Limitations section (ALS) for Airbus Model A310 airplanes and Airbus Model A300–600 series airplanes has been updated. The new CMRs, among other things, introduce new inspections. CMRs are intended to detect safety-significant latent failures that would, in combination with one or more other specific failures or events, result in a hazardous or catastrophic failure condition of avionics, hydraulic systems, fire detection systems, fuel systems, or other critical systems. described above. We have examined the DGAC’s findings, evaluated all pertinent information, and determined that we need to issue an AD for airplanes of this type design that are certificated for operation in the United States. Therefore, we are proposing this AD, which would require revising the Airworthiness Limitations section of the Instructions for Continued Airworthiness by incorporating new and revised CMRs. Relevant Service Information Airbus has issued A310 Certification Maintenance Requirements AI/ST5/849/ 85, Issue 12, dated February 2005, to Part 3 of the ALS for Model A310. Airbus has also issued A300–600 Certification Maintenance Requirements AI/ST5/829/85, Issue 12, dated February 2005, to Part 3 of the ALS for Model A300–600. Issue 12 of the documents: • Adds two new Two Star CMR tasks for the thrust reverser actuation and cowling; • Corrects existing CMRs; and • For Model A300–600: Extends the applicability of a CMR and corrects the effectivity paragraph of the CMR. Accomplishing the actions specified in the service information is intended to adequately address the unsafe condition. The DGAC mandated the service information and issued French airworthiness directive F–2005–123, dated July 20, 2005, to ensure the continued airworthiness of these airplanes in France. Clarification of Compliance Time Between the Proposed AD and the French Airworthiness Directive FAA’s Determination and Requirements of the Proposed AD These airplane models are manufactured in France and are type certificated for operation in the United States under the provisions of section 21.29 of the Federal Aviation Regulations (14 CFR 21.29) and the applicable bilateral airworthiness agreement. Pursuant to this bilateral airworthiness agreement, the DGAC has kept the FAA informed of the situation The French airworthiness directive specifies to conform to the CMRs within two months with the exception of one CMR, MSI 78.30.99 (thrust reverser actuation and cowling tasks for airplanes that have installed a third line of defense). The French airworthiness directive specifies to conform to MSI 78.30.99 within three months or before the accumulation of 7,000 flight hours since installation of a third line of defense, whichever occurs later. However, this proposed AD would require revising the Airworthiness Limitations section of the Instructions for Continued Airworthiness by incorporating new and revised certification maintenance requirements within three months after the effective date of the proposed AD. In developing an appropriate compliance time for this action, we considered the urgency associated with the subject unsafe condition, the availability of required parts, and the practical aspect of affected operators accomplishing the operational and functional tests of critical systems and power plants and inspections for damage of certain parts that are specified in the CMRs. Costs of Compliance The following table provides the estimated costs for U.S. operators to comply with this proposed AD. ESTIMATED COSTS Action Revision of maintenance program ................................... rmajette on PROD1PC67 with PROPOSALS Authority for This Rulemaking Title 49 of the United States Code specifies the FAA’s authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII, Aviation Programs, describes in more VerDate Aug<31>2005 11:52 Feb 05, 2007 Average labor rate per hour Work hours Jkt 211001 1 $80 detail the scope of the Agency’s authority. We are issuing this rulemaking under the authority described in subtitle VII, part A, subpart III, section 44701, ‘‘General requirements.’’ Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in PO 00000 Frm 00016 Fmt 4702 Sfmt 4702 Cost per airplane Number of U.S.registered airplanes $80 203 Fleet cost $16,240 air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on E:\FR\FM\06FEP1.SGM 06FEP1 5364 Federal Register / Vol. 72, No. 24 / Tuesday, February 6, 2007 / Proposed Rules products identified in this rulemaking action. Regulatory Findings We have determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government. For the reasons discussed above, I certify that the proposed regulation: 1. Is not a ‘‘significant regulatory action’’ under Executive Order 12866; 2. Is not a ‘‘significant rule’’ under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and 3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. We prepared a regulatory evaluation of the estimated costs to comply with this proposed AD and placed it in the AD docket. See the ADDRESSES section for a location to examine the regulatory evaluation. List of Subjects in 14 CFR Part 39 Air transportation, Aircraft, Aviation safety, Safety. The Proposed Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows: PART 39—AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. § 39.13 [Amended] 2. The Federal Aviation Administration (FAA) amends § 39.13 by adding the following new airworthiness directive (AD): Airbus: Docket No. FAA–2007–27154; Directorate Identifier 2006–NM–139–AD. rmajette on PROD1PC67 with PROPOSALS Comments Due Date (a) The FAA must receive comments on this AD action by March 8, 2007. Affected ADs (b) None. Applicability (c) This AD applies to all Airbus Model A310 airplanes, Model A300 B4–601, B4– 603, B4–620, and B4–622 airplanes, Model A300 B4–605R and B4–622R airplanes, Model A300 F4–605R and F4–622R VerDate Aug<31>2005 11:52 Feb 05, 2007 Jkt 211001 airplanes, and Model A300 C4–605R Variant F airplanes, certificated in any category. Note 1: This AD requires revisions to certain operator maintenance documents to include new inspections. Compliance with these actions is required by 14 CFR 91.403(c). For airplanes that have been previously modified, altered, or repaired in the areas addressed by these inspections, the operator may not be able to accomplish the inspections described in the revisions. In this situation, to comply with 14 CFR 91.403(c), the operator must request approval for an alternative method of compliance according to paragraph (g) of this AD. The request should include a description of changes to the required inspections that will ensure the continued damage tolerance of the affected structure. The FAA has provided guidance for this determination in Advisory Circular (AC) 25.1529–1. Unsafe Condition (d) This AD results from the manufacturer determining that additional and revised certification maintenance requirements are necessary in order to ensure continued operational safety of the affected airplanes. We are issuing this AD to prevent safetysignificant latent failures that would, in combination with one or more other specific failures or events, result in a hazardous or catastrophic failure condition of avionics, hydraulic systems, fire detection systems, fuel systems, or other critical systems. Compliance (e) You are responsible for having the actions required by this AD performed within the compliance times specified, unless the actions have already been done. Revise the Airworthiness Limitations Section of the Instructions for Continued Airworthiness (f) Within three months after the effective date of this AD, revise the Airworthiness Limitations section of the Instructions for Continued Airworthiness by incorporating Airbus A300–600 Certification Maintenance Requirements (CMRs) AI/ST5/829/85, Issue 12, dated February 2005 (for Model A310 airplanes); or Airbus A310 CMR AI/ST5/849/ 85, Issue 12, dated February 2005 (for Model A300 B4–601, B4–603, B4–620, and B4–622 airplanes, Model A300 B4–605R and B4– 622R airplanes, Model A300 F4–605R and F4–622R airplanes, and Model A300 C4– 605R Variant F airplanes); as applicable. Accomplish the actions specified in the applicable CMRs at the times specified in the applicable CMRs. The actions must be accomplished in accordance with the applicable CMRs. Alternative Methods of Compliance (AMOCs) (g)(1) The Manager, International Branch, ANM–116, Transport Airplane Directorate, FAA, has the authority to approve AMOCs for this AD, if requested in accordance with the procedures found in 14 CFR 39.19. (2) Before using any AMOC approved in accordance with § 39.19 on any airplane to which the AMOC applies, notify the appropriate principal inspector in the FAA PO 00000 Frm 00017 Fmt 4702 Sfmt 4702 Flight Standards Certificate Holding District Office. Related Information (h) French airworthiness directive F–2005– 123, dated July 20, 2005, also addresses the subject of this AD. Issued in Renton, Washington, on January 29, 2007. Ali Bahrami, Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. E7–1872 Filed 2–5–07; 8:45 am] BILLING CODE 4910–13–P DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2006–26494; Directorate Identifier 2006–CE–79–AD] RIN 2120–AA64 Airworthiness Directives; Alpha Aviation Design Limited (Type Certificate No. A48EU previously held by APEX Aircraft and AVIONS PIERRE ROBIN) Model R2160 Airplanes Federal Aviation Administration (FAA), Department of Transportation (DOT). ACTION: Notice of proposed rulemaking (NPRM). AGENCY: SUMMARY: We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: * * * unchecked corrosion developing on the wing spars due to access for inspections being difficult under normal maintenance practices, which could lead to an unsafe condition and possibly a failure of the wing. The proposed AD would require actions that are intended to address the unsafe condition described in the MCAI. DATES: We must receive comments on this proposed AD by March 8, 2007. ADDRESSES: You may send comments by any of the following methods: • DOT Docket Web site: Go to https://dms.dot.gov and follow the instructions for sending your comments electronically. • Fax: (202) 493–2251. • Mail: Docket Management Facility, U.S. Department of Transportation, 400 Seventh Street, SW., Nassif Building, Room PL–401, Washington, DC 20590– 0001. E:\FR\FM\06FEP1.SGM 06FEP1

Agencies

[Federal Register Volume 72, Number 24 (Tuesday, February 6, 2007)]
[Proposed Rules]
[Pages 5362-5364]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: E7-1872]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2007-27154; Directorate Identifier 2006-NM-139-AD]
RIN 2120-AA64


Airworthiness Directives; Airbus Model A310 Airplanes and Model 
A300 B4-600, B4-600R, and F4-600R Series Airplanes, and Model C4-605R 
Variant F airplanes (Collectively Called A300-600 Series Airplanes)

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) 
for all Airbus Model A310 airplanes and Model A300-600 series 
airplanes. This proposed AD would require revising the Airworthiness 
Limitations section of the Instructions for Continued Airworthiness by 
incorporating new and revised certification maintenance requirements. 
This proposed AD results from the manufacturer determining that 
additional and revised certification maintenance requirements are 
necessary in order to ensure continued operational safety of the 
affected airplanes. We are proposing this AD to prevent safety-
significant latent failures that would, in combination with one or more 
other specific failures or events, result in a hazardous or 
catastrophic failure condition of avionics, hydraulic systems, fire 
detection systems, fuel systems, or other critical systems.

DATES: We must receive comments on this proposed AD by March 8, 2007.

ADDRESSES: Use one of the following addresses to submit comments on 
this proposed AD.
     DOT Docket Web site: Go to https://dms.dot.gov and follow 
the instructions for sending your comments electronically.
     Government-wide rulemaking Web site: Go to https://
www.regulations.gov and follow the instructions for sending your 
comments electronically.
     Mail: Docket Management Facility, U.S. Department of 
Transportation, 400 Seventh Street, SW., Nassif Building, room PL-401, 
Washington, DC 20590.
     Fax: (202) 493-2251.
     Hand Delivery: Room PL-401 on the plaza level of the 
Nassif Building, 400 Seventh Street, SW., Washington, DC, between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    Contact Airbus, 1 Rond Point Maurice Bellonte, 31707 Blagnac Cedex, 
France, for service information identified in this proposed AD.

FOR FURTHER INFORMATION CONTACT: Tom Stafford, Aerospace Engineer, 
International Branch, ANM-116, FAA, Transport Airplane Directorate, 
1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425) 
227-1622; fax (425) 227-1149.

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to submit any relevant written data, views, or 
arguments regarding this proposed AD. Send your comments to an address 
listed in the ADDRESSES section. Include the docket

[[Page 5363]]

number ``FAA-2007-27154; Directorate Identifier 2006-NM-139-AD'' at the 
beginning of your comments. We specifically invite comments on the 
overall regulatory, economic, environmental, and energy aspects of the 
proposed AD. We will consider all comments received by the closing date 
and may amend the proposed AD in light of those comments.
    We will post all comments we receive, without change, to https://
dms.dot.gov, including any personal information you provide. We will 
also post a report summarizing each substantive verbal contact with FAA 
personnel concerning this proposed AD. Using the search function of 
that Web site, anyone can find and read the comments in any of our 
dockets, including the name of the individual who sent the comment (or 
signed the comment on behalf of an association, business, labor union, 
etc.). You may review the DOT's complete Privacy Act Statement in the 
Federal Register published on April 11, 2000 (65 FR 19477-78), or you 
may visit https://dms.dot.gov.

Examining the Docket

    You may examine the AD docket on the Internet at https://
dms.dot.gov, or in person at the Docket Management Facility office 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The Docket Management Facility office (telephone (800) 647-
5227) is located on the plaza level of the Nassif Building at the DOT 
street address stated in the ADDRESSES section. Comments will be 
available in the AD docket shortly after the Docket Management System 
receives them.

Discussion

    The Direction G[eacute]n[eacute]rale de l'Aviation Civile (DGAC), 
which is the airworthiness authority for France, notified us that Part 
3, ``Certification Maintenance Requirements (CMR)'' of the 
Airworthiness Limitations section (ALS) for Airbus Model A310 airplanes 
and Airbus Model A300-600 series airplanes has been updated. The new 
CMRs, among other things, introduce new inspections. CMRs are intended 
to detect safety-significant latent failures that would, in combination 
with one or more other specific failures or events, result in a 
hazardous or catastrophic failure condition of avionics, hydraulic 
systems, fire detection systems, fuel systems, or other critical 
systems.

Relevant Service Information

    Airbus has issued A310 Certification Maintenance Requirements AI/
ST5/849/85, Issue 12, dated February 2005, to Part 3 of the ALS for 
Model A310. Airbus has also issued A300-600 Certification Maintenance 
Requirements AI/ST5/829/85, Issue 12, dated February 2005, to Part 3 of 
the ALS for Model A300-600. Issue 12 of the documents:
     Adds two new Two Star CMR tasks for the thrust reverser 
actuation and cowling;
     Corrects existing CMRs; and
     For Model A300-600: Extends the applicability of a CMR and 
corrects the effectivity paragraph of the CMR.
    Accomplishing the actions specified in the service information is 
intended to adequately address the unsafe condition. The DGAC mandated 
the service information and issued French airworthiness directive F-
2005-123, dated July 20, 2005, to ensure the continued airworthiness of 
these airplanes in France.

FAA's Determination and Requirements of the Proposed AD

    These airplane models are manufactured in France and are type 
certificated for operation in the United States under the provisions of 
section 21.29 of the Federal Aviation Regulations (14 CFR 21.29) and 
the applicable bilateral airworthiness agreement. Pursuant to this 
bilateral airworthiness agreement, the DGAC has kept the FAA informed 
of the situation described above. We have examined the DGAC's findings, 
evaluated all pertinent information, and determined that we need to 
issue an AD for airplanes of this type design that are certificated for 
operation in the United States.
    Therefore, we are proposing this AD, which would require revising 
the Airworthiness Limitations section of the Instructions for Continued 
Airworthiness by incorporating new and revised CMRs.

Clarification of Compliance Time Between the Proposed AD and the French 
Airworthiness Directive

    The French airworthiness directive specifies to conform to the CMRs 
within two months with the exception of one CMR, MSI 78.30.99 (thrust 
reverser actuation and cowling tasks for airplanes that have installed 
a third line of defense). The French airworthiness directive specifies 
to conform to MSI 78.30.99 within three months or before the 
accumulation of 7,000 flight hours since installation of a third line 
of defense, whichever occurs later.
    However, this proposed AD would require revising the Airworthiness 
Limitations section of the Instructions for Continued Airworthiness by 
incorporating new and revised certification maintenance requirements 
within three months after the effective date of the proposed AD. In 
developing an appropriate compliance time for this action, we 
considered the urgency associated with the subject unsafe condition, 
the availability of required parts, and the practical aspect of 
affected operators accomplishing the operational and functional tests 
of critical systems and power plants and inspections for damage of 
certain parts that are specified in the CMRs.

Costs of Compliance

    The following table provides the estimated costs for U.S. operators 
to comply with this proposed AD.

                                                 Estimated Costs
----------------------------------------------------------------------------------------------------------------
                                                                                Number of U.S.-
             Action                Work hours     Average labor    Cost per       registered        Fleet cost
                                                  rate per hour    airplane        airplanes
----------------------------------------------------------------------------------------------------------------
Revision of maintenance program               1             $80          $80                 203         $16,240
----------------------------------------------------------------------------------------------------------------

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII, Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
subtitle VII, part A, subpart III, section 44701, ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on

[[Page 5364]]

products identified in this rulemaking action.

Regulatory Findings

    We have determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify that the proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979); and
    3. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a regulatory evaluation of the estimated costs to 
comply with this proposed AD and placed it in the AD docket. See the 
ADDRESSES section for a location to examine the regulatory evaluation.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

    1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

    2. The Federal Aviation Administration (FAA) amends Sec.  39.13 by 
adding the following new airworthiness directive (AD):

Airbus: Docket No. FAA-2007-27154; Directorate Identifier 2006-NM-
139-AD.

Comments Due Date

    (a) The FAA must receive comments on this AD action by March 8, 
2007.

Affected ADs

    (b) None.

Applicability

    (c) This AD applies to all Airbus Model A310 airplanes, Model 
A300 B4-601, B4-603, B4-620, and B4-622 airplanes, Model A300 B4-
605R and B4-622R airplanes, Model A300 F4-605R and F4-622R 
airplanes, and Model A300 C4-605R Variant F airplanes, certificated 
in any category.

    Note 1: This AD requires revisions to certain operator 
maintenance documents to include new inspections. Compliance with 
these actions is required by 14 CFR 91.403(c). For airplanes that 
have been previously modified, altered, or repaired in the areas 
addressed by these inspections, the operator may not be able to 
accomplish the inspections described in the revisions. In this 
situation, to comply with 14 CFR 91.403(c), the operator must 
request approval for an alternative method of compliance according 
to paragraph (g) of this AD. The request should include a 
description of changes to the required inspections that will ensure 
the continued damage tolerance of the affected structure. The FAA 
has provided guidance for this determination in Advisory Circular 
(AC) 25.1529-1.

Unsafe Condition

    (d) This AD results from the manufacturer determining that 
additional and revised certification maintenance requirements are 
necessary in order to ensure continued operational safety of the 
affected airplanes. We are issuing this AD to prevent safety-
significant latent failures that would, in combination with one or 
more other specific failures or events, result in a hazardous or 
catastrophic failure condition of avionics, hydraulic systems, fire 
detection systems, fuel systems, or other critical systems.

Compliance

    (e) You are responsible for having the actions required by this 
AD performed within the compliance times specified, unless the 
actions have already been done.

Revise the Airworthiness Limitations Section of the Instructions for 
Continued Airworthiness

    (f) Within three months after the effective date of this AD, 
revise the Airworthiness Limitations section of the Instructions for 
Continued Airworthiness by incorporating Airbus A300-600 
Certification Maintenance Requirements (CMRs) AI/ST5/829/85, Issue 
12, dated February 2005 (for Model A310 airplanes); or Airbus A310 
CMR AI/ST5/849/85, Issue 12, dated February 2005 (for Model A300 B4-
601, B4-603, B4-620, and B4-622 airplanes, Model A300 B4-605R and 
B4-622R airplanes, Model A300 F4-605R and F4-622R airplanes, and 
Model A300 C4-605R Variant F airplanes); as applicable. Accomplish 
the actions specified in the applicable CMRs at the times specified 
in the applicable CMRs. The actions must be accomplished in 
accordance with the applicable CMRs.

Alternative Methods of Compliance (AMOCs)

    (g)(1) The Manager, International Branch, ANM-116, Transport 
Airplane Directorate, FAA, has the authority to approve AMOCs for 
this AD, if requested in accordance with the procedures found in 14 
CFR 39.19.
    (2) Before using any AMOC approved in accordance with Sec.  
39.19 on any airplane to which the AMOC applies, notify the 
appropriate principal inspector in the FAA Flight Standards 
Certificate Holding District Office.

Related Information

    (h) French airworthiness directive F-2005-123, dated July 20, 
2005, also addresses the subject of this AD.

    Issued in Renton, Washington, on January 29, 2007.
Ali Bahrami,
Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. E7-1872 Filed 2-5-07; 8:45 am]
BILLING CODE 4910-13-P
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.