Airworthiness Directives; Bombardier Model CL-600-2C10 (Regional Jet Series 700, 701, & 702), CL-600-2D15 (Regional Jet Series 705), and CL-600-2D24 (Regional Jet Series 900) Airplanes, 67946-67948 [05-22307]

Download as PDF 67946 Federal Register / Vol. 70, No. 216 / Wednesday, November 9, 2005 / Proposed Rules (3) Before using any AMOC approved in accordance with § 39.19 on any airplane to which the AMOC applies, notify the appropriate principal inspector in the FAA Flight Standards Certificate Holding District Office. Issued in Renton, Washington, on November 3, 2005. Ali Bahrami, Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. 05–22310 Filed 11–8–05; 8:45 am] BILLING CODE 4910–13–P DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2005–22872; Directorate Identifier 2005–NM–198–AD] RIN 2120–AA64 Airworthiness Directives; Bombardier Model CL–600–2C10 (Regional Jet Series 700, 701, & 702), CL–600–2D15 (Regional Jet Series 705), and CL–600– 2D24 (Regional Jet Series 900) Airplanes Federal Aviation Administration (FAA), Department of Transportation (DOT). ACTION: Notice of proposed rulemaking (NPRM). AGENCY: SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) for certain Bombardier Model CL–600– 2C10 (Regional Jet Series 700, 701, & 702), CL–600–2D15 (Regional Jet Series 705), and CL–600–2D24 (Regional Jet Series 900) airplanes. This proposed AD would require replacing the Camloc fasteners on the sidewall of the center pedestal. This proposed AD results from reports of the Camloc fasteners on the sidewall of the center pedestal disengaging and interfering with an inboard rudder pedal. We are proposing this AD to prevent these fasteners from disengaging and interfering with an inboard rudder pedal, which could reduce directional controllability of the airplane. DATES: We must receive comments on this proposed AD by December 9, 2005. ADDRESSES: Use one of the following addresses to submit comments on this proposed AD. • DOT Docket Web site: Go to https://dms.dot.gov and follow the instructions for sending your comments electronically. • Government-wide rulemaking Web site: Go to https://www.regulations.gov and follow the instructions for sending your comments electronically. VerDate Aug<31>2005 16:05 Nov 08, 2005 Jkt 208001 • Mail: Docket Management Facility, U.S. Department of Transportation, 400 Seventh Street, SW., Nassif Building, Room PL–401, Washington, DC 20590. • Fax: (202) 493–2251. • Hand Delivery: Room PL–401 on the plaza level of the Nassif Building, 400 Seventh Street, SW., Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. Contact Bombardier, Inc., Canadair, Aerospace Group, P.O. Box 6087, Station Centre-ville, Montreal, Quebec H3C 3G9, Canada, for service information identified in this proposed AD. FOR FURTHER INFORMATION CONTACT: Daniel Parrillo, Aerospace Engineer, Systems and Flight Test Branch, ANE– 172, FAA, New York Aircraft Certification Office, 1600 Stewart Avenue, suite 410, Westbury, New York 11590; telephone (516) 228–7305; fax (516) 794–5531. SUPPLEMENTARY INFORMATION: Comments Invited We invite you to submit any relevant written data, views, or arguments regarding this proposed AD. Send your comments to an address listed in the ADDRESSES section. Include the docket number ‘‘FAA–2005–22872; Directorate Identifier 2005–NM–198–AD’’ at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of the proposed AD. We will consider all comments received by the closing date and may amend the proposed AD in light of those comments. We will post all comments we receive, without change, to https:// dms.dot.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact with FAA personnel concerning this proposed AD. Using the search function of that Web site, anyone can find and read the comments in any of our dockets, including the name of the individual who sent the comment (or signed the comment on behalf of an association, business, labor union, etc.). You may review the DOT’s complete Privacy Act Statement in the Federal Register published on April 11, 2000 (65 FR 19477–78), or you may visit https:// dms.dot.gov. Examining the Docket You may examine the AD docket on the Internet at https://dms.dot.gov, or in person at the Docket Management Facility office between 9 a.m. and 5 p.m., Monday through Friday, except PO 00000 Frm 00016 Fmt 4702 Sfmt 4702 Federal holidays. The Docket Management Facility office (telephone (800) 647–5227) is located on the plaza level of the Nassif Building at the DOT street address stated in the ADDRESSES section. Comments will be available in the AD docket shortly after the Docket Management System receives them. Discussion Transport Canada Civil Aviation (TCCA), which is the airworthiness authority for Canada, notified us that an unsafe condition may exist on certain Bombardier Model CL–600–2C10 (Regional Jet Series 700, 701, & 702), CL–600–2D15 (Regional Jet Series 705), and CL–600–2D24 (Regional Jet Series 900) airplanes. TCCA advises that it has received several reports of the Camloc fasteners on the sidewall of the center pedestal fully disengaging and interfering with an inboard rudder pedal. These incidents occurred on Bombardier Model CL–600–2B19 (Regional Jet Series 100 & 440) airplanes. In one incident, the rudder jammed during an approach due to a disengaged Camloc fastener that restricted movement of the pilot’s inboard rudder pedal and tow brake. This condition, if not corrected, could reduce directional controllability of the airplane. The subject configuration on certain Bombardier Model CL–600–2C10 (Regional Jet Series 700, 701, & 702), CL–600–2D15 (Regional Jet Series 705), and CL–600–2D24 (Regional Jet Series 900) airplanes is almost identical to that on the affected Model CL–600–2B19 (Regional Jet Series 100 & 440) airplanes. Therefore, those Model CL– 600–2C10 (Regional Jet Series 700, 701, & 702), CL–600–2D15 (Regional Jet Series 705), and CL–600–2D24 (Regional Jet Series 900) airplanes may be subject to the unsafe condition revealed on the Model CL–600–2B19 (Regional Jet Series 100 & 440) airplanes. Relevant Service Information Bombardier has issued Service Bulletin 670BA–25–037, Revision A, dated August 25, 2005. The service bulletin describes procedures for replacing, with screws and nut plate assemblies, the Camloc fasteners on the left and right sidewalls of the center pedestal. Accomplishing the actions specified in the service information is intended to adequately address the unsafe condition. TCCA mandated the service information and issued Canadian airworthiness directive CF– 2005–31, dated August 17, 2005, to ensure the continued airworthiness of these airplanes in Canada. E:\FR\FM\09NOP1.SGM 09NOP1 Federal Register / Vol. 70, No. 216 / Wednesday, November 9, 2005 / Proposed Rules FAA’s Determination and Requirements of the Proposed AD These airplane models are manufactured in Canada and are type certificated for operation in the United States under the provisions of section 21.29 of the Federal Aviation Regulations (14 CFR 21.29) and the applicable bilateral airworthiness agreement. Pursuant to this bilateral airworthiness agreement, TCCA has kept the FAA informed of the situation described above. We have examined TCAA’s findings, evaluated all pertinent information, and determined that we need to issue an AD for airplanes of these type designs that are certificated for operation in the United States. Therefore, we are proposing this AD, which would require accomplishing the actions specified in the service information described previously. Costs of Compliance This proposed AD would affect about 209 airplanes of U.S. registry. The proposed actions would take about 2 work hours per airplane, at an average labor rate of $65 per work hour. Required parts would cost between $141 and $150 per airplane. Based on these figures, the estimated cost of the proposed AD for U.S. operators is between $56,639 and $58,520, or between $271 and $280 per airplane. Authority for This Rulemaking Title 49 of the United States Code specifies the FAA’s authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII, Aviation Programs, describes in more detail the scope of the Agency’s authority. We are issuing this rulemaking under the authority described in subtitle VII, part A, subpart III, section 44701, ‘‘General requirements.’’ Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. Regulatory Findings We have determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the National Government and the States, or on the distribution of power and responsibilities among the various levels of government. For the reasons discussed above, I certify that the proposed regulation: 1. Is not a ‘‘significant regulatory action’’ under Executive Order 12866; 2. Is not a ‘‘significant rule’’ under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and 3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. 67947 We prepared a regulatory evaluation of the estimated costs to comply with this proposed AD and placed it in the AD docket. See the ADDRESSES section for a location to examine the regulatory evaluation. List of Subjects in 14 CFR Part 39 Air transportation, Aircraft, Aviation safety, Safety. The Proposed Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows: PART 39—AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. § 39.13 [Amended] 2. The Federal Aviation Administration (FAA) amends § 39.13 by adding the following new airworthiness directive (AD): Bombardier, Inc. (Formerly Canadair): Docket No. FAA–2005–22872; Directorate Identifier 2005–NM–198–AD. Comments Due Date (a) The FAA must receive comments on this AD action by December 9, 2005. Affected ADs (b) None. Applicability (c) This AD applies to the airplanes identified in Table 1 of this AD, certificated in any category. TABLE 1.—APPLICABILITY Bombardier models Serial numbers CL–600–2C10 (Regional Jet Series 700, 701, & 702) ................................................................... CL–600–2D15 (Regional Jet Series 705); CL–600–2D24 (Regional Jet Series 900) ................... 10003 through 10218 inclusive. 15001 through 15047 inclusive. Unsafe Condition accordance with the procedures found in 14 CFR 39.19. (2) Before using any AMOC approved in accordance with § 39.19 on any airplane to which the AMOC applies, notify the appropriate principal inspector in the FAA Flight Standards Certificate Holding District Office. (d) This AD results from reports of the Camloc fasteners on the sidewall of the center pedestal disengaging and interfering with an inboard rudder pedal. We are issuing this AD to prevent these fasteners from disengaging and interfering with an inboard rudder pedal, which could reduce directional controllability of the airplane. Compliance (e) You are responsible for having the actions required by this AD performed within the compliance times specified, unless the actions have already been done. Replacement of Fasteners (f) Within 5,500 flight hours after the effective date of this AD, replace, with screws VerDate Aug<31>2005 16:05 Nov 08, 2005 Jkt 208001 and nut plate assemblies, the Camloc fasteners on the left and right sidewalls of the center pedestal, in accordance with the Accomplishment Instructions of Bombardier Service Bulletin 670BA–25–037, Revision A, dated August 25, 2005. Actions Accomplished Previously (g) Replacing fasteners before the effective date of this AD in accordance with the Accomplishment Instructions of Bombardier Service Bulletin 670BA–25–037, dated June 23, 2005, is acceptable for compliance with the requirements of paragraph (f) of this AD. Related Information (i) Canadian airworthiness directive CF– 2005–31, dated August 17, 2005, also addresses the subject of this AD. Alternative Methods of Compliance (AMOCs) (h)(1) The Manager, New York Aircraft Certification Office, FAA, has the authority to approve AMOCs for this AD, if requested in PO 00000 Frm 00017 Fmt 4702 Sfmt 4702 E:\FR\FM\09NOP1.SGM 09NOP1 67948 Federal Register / Vol. 70, No. 216 / Wednesday, November 9, 2005 / Proposed Rules Issued in Renton, Washington, on October 28, 2005. Kalene C. Yanamura, Acting Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. 05–22307 Filed 11–8–05; 8:45 am] BILLING CODE 4910–13–P DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2005–22871; Directorate Identifier 2005–NM–191–AD] RIN 2120–AA64 Airworthiness Directives; Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model EMB–120, –120ER, –120FC, –120QC, and –120RT Airplanes Federal Aviation Administration (FAA), Department of Transportation (DOT). ACTION: Notice of proposed rulemaking (NPRM). AGENCY: SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) for certain EMBRAER Model EMB–120, –120ER, –120FC, –120QC, and –120RT airplanes. This proposed AD would require installing a rivet and washer in the hole of the upper frame of the auxiliary power unit (APU) firewall. This proposed AD results from a report indicating that, during production, a pinhole was left open at the upper frame of the APU firewall. We are proposing this AD to ensure that the APU compartment is isolated from the rest of the airplane in the event of an APU fire. DATES: We must receive comments on this proposed AD by December 9, 2005. ADDRESSES: Use one of the following addresses to submit comments on this proposed AD. • DOT Docket Web site: Go to https://dms.dot.gov and follow the instructions for sending your comments electronically. • Government-wide rulemaking Web site: Go to https://www.regulations.gov and follow the instructions for sending your comments electronically. • Mail: Docket Management Facility, U.S. Department of Transportation, 400 Seventh Street SW., Nassif Building, room PL–401, Washington, DC 20590. • Fax: (202) 493–2251. • Hand Delivery: Room PL–401 on the plaza level of the Nassif Building, 400 Seventh Street SW., Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. VerDate Aug<31>2005 16:05 Nov 08, 2005 Jkt 208001 Contact Empresa Brasileira de Aeronautica S.A. (EMBRAER), P.O. Box 343–CEP 12.225, Sao Jose dos Campos— SP, Brazil, for service information identified in this proposed AD. FOR FURTHER INFORMATION CONTACT: Dan Rodina, Aerospace Engineer, International Branch, ANM–116, FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington 98055–4056; telephone (425) 227–2125; fax (425) 227–1149. SUPPLEMENTARY INFORMATION: Comments Invited We invite you to submit any relevant written data, views, or arguments regarding this proposed AD. Send your comments to an address listed in the ADDRESSES section. Include the docket number ‘‘FAA–2005–22871; Directorate Identifier 2005–NM–191–AD’’ at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of the proposed AD. We will consider all comments received by the closing date and may amend the proposed AD in light of those comments. We will post all comments we receive, without change, to https:// dms.dot.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact with FAA personnel concerning this proposed AD. Using the search function of that web site, anyone can find and read the comments in any of our dockets, including the name of the individual who sent the comment (or signed the comment on behalf of an association, business, labor union, etc.). You may review the DOT’s complete Privacy Act Statement in the Federal Register published on April 11, 2000 (65 FR 19477–78), or you may visit https:// dms.dot.gov. Examining the Docket You may examine the AD docket on the Internet at https://dms.dot.gov, or in person at the Docket Management Facility office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The Docket Management Facility office (telephone (800) 647–5227) is located on the plaza level of the Nassif Building at the DOT street address stated in the ADDRESSES section. Comments will be available in the AD docket shortly after the Docket Management System receives them. Discussion The Departmento de Aviacao Civil (DAC), which is the airworthiness authority for Brazil, notified us that an PO 00000 Frm 00018 Fmt 4702 Sfmt 4702 unsafe condition may exist on certain EMBRAER Model EMB–120, –120ER, –120FC, –120QC, and –120RT airplanes. The DAC advises that a pinhole used for the manufacturing process was left open. The hole was at the upper frame of the auxiliary power unit (APU) firewall. To meet the sealing requirements for the firewall, a rivet and stainless steel washer must be installed. In the event of an APU fire, a hole in the firewall would not isolate the APU compartment from the rest of the airplane. Relevant Service Information EMBRAER has issued Service Bulletin 120–53–0080, dated November 30, 2004. The service bulletin describes procedures for installing a rivet and stainless steel washer in the hole of the upper frame of the APU firewall. Accomplishing the actions specified in the service information is intended to adequately address the unsafe condition. The DAC mandated the service information and issued Brazilian airworthiness directive 2005–08–03, dated September 5, 2005, to ensure the continued airworthiness of these airplanes in Brazil. FAA’s Determination and Requirements of the Proposed AD These airplane models are manufactured in Brazil and are type certificated for operation in the United States under the provisions of section 21.29 of the Federal Aviation Regulations (14 CFR 21.29) and the applicable bilateral airworthiness agreement. Pursuant to this bilateral airworthiness agreement, the DAC has kept the FAA informed of the situation described above. We have examined the DAC’s findings, evaluated all pertinent information, and determined that we need to issue an AD for airplanes of this type design that are certificated for operation in the United States. Therefore, we are proposing this AD, which would require accomplishing the actions specified in the service information described previously, except as discussed below. Differences Between the Proposed AD and the Brazilian Airworthiness Directive The Brazilian airworthiness directive applies to ‘‘all Embraer EMB–120( ) aircraft models in operation.’’ However, this proposed AD would apply only to the airplanes with the serial numbers identified in the EMBRAER service bulletin. Airplanes not identified receive an equivalent modification during production. E:\FR\FM\09NOP1.SGM 09NOP1

Agencies

[Federal Register Volume 70, Number 216 (Wednesday, November 9, 2005)]
[Proposed Rules]
[Pages 67946-67948]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 05-22307]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2005-22872; Directorate Identifier 2005-NM-198-AD]
RIN 2120-AA64


Airworthiness Directives; Bombardier Model CL-600-2C10 (Regional 
Jet Series 700, 701, & 702), CL-600-2D15 (Regional Jet Series 705), and 
CL-600-2D24 (Regional Jet Series 900) Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) 
for certain Bombardier Model CL-600-2C10 (Regional Jet Series 700, 701, 
& 702), CL-600-2D15 (Regional Jet Series 705), and CL-600-2D24 
(Regional Jet Series 900) airplanes. This proposed AD would require 
replacing the Camloc fasteners on the sidewall of the center pedestal. 
This proposed AD results from reports of the Camloc fasteners on the 
sidewall of the center pedestal disengaging and interfering with an 
inboard rudder pedal. We are proposing this AD to prevent these 
fasteners from disengaging and interfering with an inboard rudder 
pedal, which could reduce directional controllability of the airplane.

DATES: We must receive comments on this proposed AD by December 9, 
2005.

ADDRESSES: Use one of the following addresses to submit comments on 
this proposed AD.
     DOT Docket Web site: Go to https://dms.dot.gov and follow 
the instructions for sending your comments electronically.
     Government-wide rulemaking Web site: Go to https://
www.regulations.gov and follow the instructions for sending your 
comments electronically.
     Mail: Docket Management Facility, U.S. Department of 
Transportation, 400 Seventh Street, SW., Nassif Building, Room PL-401, 
Washington, DC 20590.
     Fax: (202) 493-2251.
     Hand Delivery: Room PL-401 on the plaza level of the 
Nassif Building, 400 Seventh Street, SW., Washington, DC, between 9 
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
    Contact Bombardier, Inc., Canadair, Aerospace Group, P.O. Box 6087, 
Station Centre-ville, Montreal, Quebec H3C 3G9, Canada, for service 
information identified in this proposed AD.

FOR FURTHER INFORMATION CONTACT: Daniel Parrillo, Aerospace Engineer, 
Systems and Flight Test Branch, ANE-172, FAA, New York Aircraft 
Certification Office, 1600 Stewart Avenue, suite 410, Westbury, New 
York 11590; telephone (516) 228-7305; fax (516) 794-5531.

SUPPLEMENTARY INFORMATION: 

Comments Invited

    We invite you to submit any relevant written data, views, or 
arguments regarding this proposed AD. Send your comments to an address 
listed in the ADDRESSES section. Include the docket number ``FAA-2005-
22872; Directorate Identifier 2005-NM-198-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of the proposed AD. We will 
consider all comments received by the closing date and may amend the 
proposed AD in light of those comments.
    We will post all comments we receive, without change, to https://
dms.dot.gov, including any personal information you provide. We will 
also post a report summarizing each substantive verbal contact with FAA 
personnel concerning this proposed AD. Using the search function of 
that Web site, anyone can find and read the comments in any of our 
dockets, including the name of the individual who sent the comment (or 
signed the comment on behalf of an association, business, labor union, 
etc.). You may review the DOT's complete Privacy Act Statement in the 
Federal Register published on April 11, 2000 (65 FR 19477-78), or you 
may visit https://dms.dot.gov.

Examining the Docket

    You may examine the AD docket on the Internet at https://
dms.dot.gov, or in person at the Docket Management Facility office 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The Docket Management Facility office (telephone (800) 647-
5227) is located on the plaza level of the Nassif Building at the DOT 
street address stated in the ADDRESSES section. Comments will be 
available in the AD docket shortly after the Docket Management System 
receives them.

Discussion

    Transport Canada Civil Aviation (TCCA), which is the airworthiness 
authority for Canada, notified us that an unsafe condition may exist on 
certain Bombardier Model CL-600-2C10 (Regional Jet Series 700, 701, & 
702), CL-600-2D15 (Regional Jet Series 705), and CL-600-2D24 (Regional 
Jet Series 900) airplanes. TCCA advises that it has received several 
reports of the Camloc fasteners on the sidewall of the center pedestal 
fully disengaging and interfering with an inboard rudder pedal. These 
incidents occurred on Bombardier Model CL-600-2B19 (Regional Jet Series 
100 & 440) airplanes. In one incident, the rudder jammed during an 
approach due to a disengaged Camloc fastener that restricted movement 
of the pilot's inboard rudder pedal and tow brake. This condition, if 
not corrected, could reduce directional controllability of the 
airplane.
    The subject configuration on certain Bombardier Model CL-600-2C10 
(Regional Jet Series 700, 701, & 702), CL-600-2D15 (Regional Jet Series 
705), and CL-600-2D24 (Regional Jet Series 900) airplanes is almost 
identical to that on the affected Model CL-600-2B19 (Regional Jet 
Series 100 & 440) airplanes. Therefore, those Model CL-600-2C10 
(Regional Jet Series 700, 701, & 702), CL-600-2D15 (Regional Jet Series 
705), and CL-600-2D24 (Regional Jet Series 900) airplanes may be 
subject to the unsafe condition revealed on the Model CL-600-2B19 
(Regional Jet Series 100 & 440) airplanes.

Relevant Service Information

    Bombardier has issued Service Bulletin 670BA-25-037, Revision A, 
dated August 25, 2005. The service bulletin describes procedures for 
replacing, with screws and nut plate assemblies, the Camloc fasteners 
on the left and right sidewalls of the center pedestal. Accomplishing 
the actions specified in the service information is intended to 
adequately address the unsafe condition. TCCA mandated the service 
information and issued Canadian airworthiness directive CF-2005-31, 
dated August 17, 2005, to ensure the continued airworthiness of these 
airplanes in Canada.

[[Page 67947]]

FAA's Determination and Requirements of the Proposed AD

    These airplane models are manufactured in Canada and are type 
certificated for operation in the United States under the provisions of 
section 21.29 of the Federal Aviation Regulations (14 CFR 21.29) and 
the applicable bilateral airworthiness agreement. Pursuant to this 
bilateral airworthiness agreement, TCCA has kept the FAA informed of 
the situation described above. We have examined TCAA's findings, 
evaluated all pertinent information, and determined that we need to 
issue an AD for airplanes of these type designs that are certificated 
for operation in the United States.
    Therefore, we are proposing this AD, which would require 
accomplishing the actions specified in the service information 
described previously.

Costs of Compliance

    This proposed AD would affect about 209 airplanes of U.S. registry. 
The proposed actions would take about 2 work hours per airplane, at an 
average labor rate of $65 per work hour. Required parts would cost 
between $141 and $150 per airplane. Based on these figures, the 
estimated cost of the proposed AD for U.S. operators is between $56,639 
and $58,520, or between $271 and $280 per airplane.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, section 106, describes the 
authority of the FAA Administrator. Subtitle VII, Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
subtitle VII, part A, subpart III, section 44701, ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We have determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the National Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify that the proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979); and
    3. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a regulatory evaluation of the estimated costs to 
comply with this proposed AD and placed it in the AD docket. See the 
ADDRESSES section for a location to examine the regulatory evaluation.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

    1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

    2. The Federal Aviation Administration (FAA) amends Sec.  39.13 by 
adding the following new airworthiness directive (AD):

Bombardier, Inc. (Formerly Canadair): Docket No. FAA-2005-22872; 
Directorate Identifier 2005-NM-198-AD.

Comments Due Date

    (a) The FAA must receive comments on this AD action by December 
9, 2005.

Affected ADs

    (b) None.

Applicability

    (c) This AD applies to the airplanes identified in Table 1 of 
this AD, certificated in any category.

                         Table 1.--Applicability
------------------------------------------------------------------------
              Bombardier models                      Serial numbers
------------------------------------------------------------------------
CL-600-2C10 (Regional Jet Series 700, 701, &   10003 through 10218
 702).                                          inclusive.
CL-600-2D15 (Regional Jet Series 705); CL-600- 15001 through 15047
 2D24 (Regional Jet Series 900).                inclusive.
------------------------------------------------------------------------

Unsafe Condition

    (d) This AD results from reports of the Camloc fasteners on the 
sidewall of the center pedestal disengaging and interfering with an 
inboard rudder pedal. We are issuing this AD to prevent these 
fasteners from disengaging and interfering with an inboard rudder 
pedal, which could reduce directional controllability of the 
airplane.

Compliance

    (e) You are responsible for having the actions required by this 
AD performed within the compliance times specified, unless the 
actions have already been done.

Replacement of Fasteners

    (f) Within 5,500 flight hours after the effective date of this 
AD, replace, with screws and nut plate assemblies, the Camloc 
fasteners on the left and right sidewalls of the center pedestal, in 
accordance with the Accomplishment Instructions of Bombardier 
Service Bulletin 670BA-25-037, Revision A, dated August 25, 2005.

Actions Accomplished Previously

    (g) Replacing fasteners before the effective date of this AD in 
accordance with the Accomplishment Instructions of Bombardier 
Service Bulletin 670BA-25-037, dated June 23, 2005, is acceptable 
for compliance with the requirements of paragraph (f) of this AD.

Alternative Methods of Compliance (AMOCs)

    (h)(1) The Manager, New York Aircraft Certification Office, FAA, 
has the authority to approve AMOCs for this AD, if requested in 
accordance with the procedures found in 14 CFR 39.19.
    (2) Before using any AMOC approved in accordance with Sec.  
39.19 on any airplane to which the AMOC applies, notify the 
appropriate principal inspector in the FAA Flight Standards 
Certificate Holding District Office.

Related Information

    (i) Canadian airworthiness directive CF-2005-31, dated August 
17, 2005, also addresses the subject of this AD.


[[Page 67948]]


    Issued in Renton, Washington, on October 28, 2005.
Kalene C. Yanamura,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 05-22307 Filed 11-8-05; 8:45 am]
BILLING CODE 4910-13-P
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.