Notice of Applications for Modification of Exemption, 48627-48629 [05-16406]
Download as PDF
<![CDATA[
Federal Register / Vol. 70, No. 159 / Thursday, August 18, 2005 / Notices
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
[Policy Statement No. ANM–115–05–005]
Policy Statement on Acceptance of a
Component Test Method To
Demonstrate
Federal Aviation
Administration (FAA), DOT.
ACTION: Notice of final policy.
AGENCY:
SUMMARY: The Federal Aviation
Administration (FAA) announces the
availability of final policy on a
component method for demonstrating
that a seat with a replacement bottom
cushion complies with § 25.562(c)(2).
This policy addresses non-flotation
monolithic (single layer) cushions.
DATES: This final policy was issued by
the Transport Airplane Directorate on
August 9, 2005.
FOR FURTHER INFORMATION CONTACT:
Michael T. Thompson, Federal Aviation
Administration, Transport Airplane
Directorate, Transport Standards Staff,
Standardization Branch, ANM–113,
1601 Lind Avenue, SW., Renton, WA
98055–4056; telephone (425) 227–1157;
fax (425) 227–1232; e-mail;
Michael.t.thompson@faa.gov.
SUPPLEMENTARY INFORMATION:
A notice of proposed policy; request
for comments, was published in the
Federal Register on April 11, 2005 (70
FR 18453). Three commenters
responded to the request for comments.
Background
Historically, substantiating changes to
the bottom cushion of a seat certificated
to § 25.562 that could affect the lumbar
load typically required a full-scale 14g
downward dynamic test using the actual
seat. Industry desired a quicker and less
expensive method in lieu of full scale
testing. As a result, the FAA funded a
research project to develop a component
test methodology for demonstrating that
a replacement bottom cushion would
not produce a higher lumbar load than
a certificated bottom cushion for a seat
certificated to § 25.562. This research
resulted in an acceptable methodology
that is documented in DOT/FAA/AR–
05/5,I ‘‘Development and Validation of
an Aircraft Seat Cushion Component
Test—Volume I,’’ dated March 2005.
This method provides a simplified
means of demonstrating compliance
with § 25.562 and will streamline the
seat certification process by reducing
the costs and time associated with seat
certification.
13:40 Aug 17, 2005
Jkt 205001
Issued in Renton, Washington, on August
9, 2005.
Ali Bahrami,
Manager, Transport Airplane Directorate,
Aircraft Certification Service.
[FR Doc. 05–16410 Filed 8–17–05; 8:45 am]
BILLING CODE 4910–13–M
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
[Policy Statement No. ANM–115–05–10]
Replacing Restraint Systems on
Forward and Aft Facing Seats
Disposition of Comments
VerDate jul<14>2003
Seat bottom cushion changes must be
evaluated to determine that compliance
with § 25.562 is maintained when
considering both the 14g downward test
and the 16g longitudinal test specified
in the regulation. This policy addresses
demonstrating compliance with the
lumbar load criteria of § 25.562(c)(2)
that is determined in a 14g downward
test.
The final policy memorandum as well
as the disposition of public comments
received is available on the Internet at
the following address: https://
www.airweb.faa.gov/rgl. If you do not
have access to the Internet, you can
obtain a copy of the final policy
memorandum by contacting the person
listed under FOR FURTHER INFORMATION
CONTACT.
Federal Aviation
Administration (FAA), DOT.
ACTION: Notice of final policy.
48627
safety to seated occupants. Seat
performance, including the restraint
system, under dynamic conditions as
defined in § 25.562, is an important
consideration of this amendment.
Replacing a restraint system on a seat
certified under § 25.562 requires new
dynamic test(s) to be conduct using the
actual seat. These dynamic tests can be
costly and time-consuming. The FAA
conducted research and found an
acceptable new method of certifying
restraint systems using a rigid seat
fixture instead of the actual seat during
dynamic tests. This method will
significantly reduce the cost and time
associated with certifying replacement
restraint systems. This policy
memorandum presents this new means
of compliance.
The final policy as well as the
disposition of public comments
received are available on the Internet at
the following address: https://
www.airweb.faa.gov/rgl. If you do not
have access to the Internet, you can
obtain a copy of the policy by contacting
the person listed under FOR FURTHER
INFORMATION CONTACT.
Issued in Renton, Washington, on August
10, 2005.
Ali Bahrami,
Manager, Transport Airplane Directorate,
Aircraft Certification Service.
[FR Doc. 05–16409 Filed 8–17–05; 8:45 am]
BILLING CODE 4910–13–M
AGENCY:
SUMMARY: The Federal Aviation
Administration (FAA) announces the
availability of final policy on Replacing
Restraint Systems on Forward and Aft
Facing Seats.
DATES: The final policy was issued by
the Transport Airplane Directorate on
August 10, 2005.
FOR FURTHER INFORMATION CONTACT:
Mike Thompson, Federal Aviation
Administration, Transport Airplane
Directorate, Transport Standards Staff,
Standardization Branch, ANM–113,
1601 Lind Avenue SW., Renton, WA
98055–4056; telephone (425) 227–1157;
fax (425) 227–1232; e-mail:
Michael.t.thompson@faa.gov.
SUPPLEMENTARY INFORMATION:
Disposition of Comments
A notice of proposed policy was
published in the Federal Register on
April 11, 2005. Five (5) commenters
responded to the request for comments.
Background
The FAA has issued Amendment 25–
64 to provide an increased level of
PO 00000
Frm 00113
Fmt 4703
Sfmt 4703
DEPARTMENT OF TRANSPORTATION
Pipeline and Hazardous Materials
Safety Administration Office of
Hazardous Materials Safety
Notice of Applications for Modification
of Exemption
Pipeline and Hazardous
Materials Safety Administration, DOT.
ACTION: List of applications for
modification of exemption.
AGENCY:
SUMMARY: In accordance with the
procedures governing the application
for, and the processing of, exemptions
from the Department of Transportation’s
Hazardous Material Regulations (49 CFR
part 107, subpart B), notice is hereby
given that the Office of Hazardous
Materials Safety has received the
application described herein. This
notice is abbreviated to expedite
docketing and public notice. Because
the sections affected, modes of
transportation, and the nature of
application have been shown in earlier
Federal Register publications, they are
not repeated here. Request of
modifications of exemptions (e.g. to
E:\FR\FM\18AUN1.SGM
18AUN1
48628
Federal Register / Vol. 70, No. 159 / Thursday, August 18, 2005 / Notices
provide for additional hazardous
materials, packaging design changes,
additional mode of transportation, etc.)
are described in footnotes to the
application number. Application
numbers with the suffix ‘‘M’’ demote a
modification request. There applications
have been separated from the new
application for exemption to facilitate
processing.
DATES: Comments must be received on
or before September 2, 2005.
Address Comments To: Record
Center, Pipeline and Hazardous
Application
No.
Docket No.
Materials Safety Administration, U.S.
Department of Transportation,
Washington, DC 20590.
Comments should refer to the
application number and be submitted in
triplicate. If Confirmation of receipt of
comments is desired, include a selfaddressed stamped postcard showing
the exemption number.
FOR FURTHER INFORMATION CONTACT:
Copies of the applications are available
for inspection in the Records Center,
Nassif Building, 400 7th Street SW.,
Washington DC or at https://dms.dot.gov.
Regulation(s) affected
Applicant
This notice of receipt of applications
for modification of exemption is
published in accordance with Part 107
of the Federal hazardous materials
transportation law (49 U.S.C. 5117(b);
49 CFR 1.53(b)).
Issued in Washington, DC, on August 12,
2005.
R. Ryan Posten,
Exemptions Program Officer, Office of
Hazardous Materials Exemptions &
Approvals.
Modification of
exemption
Nature of exemption thereof
MODIFICATION EXEMPTIONS
4661–M .........
...........................
Chemtell Foote Corporation, Kings
Mountain, NC.
49 CFR 180.205 .......
4661
10048–M .......
...........................
Epichem, Inc., Haverhill, MA.
49 CFR 173.181;
173.187; 173.201,
202, 211, 212, 226,
227.
10048
10695–M .......
...........................
3M Company, St.
Paul, MN.
10695
10798–M .......
...........................
Chemetall Foote Corporation, Kings
Mountain, NC.
49 CFR 172.101;
172.504;
172.505(a);
173.323; 174.81;
176.84; 177.848.
49 CFR 174.67(i),(j)
10962– ..........
...........................
ICC The Compliance
Center, Niagara
Falls, NY.
49 CFR Part 172,
Subparts E, F; Part
177, Subpart C.
10962
11318–M .......
...........................
Akzo Mobel Chemicals, Inc., Chicago,
IL.
49 CFR 172.101
Special Provision
B14.
11318
11670–M .......
...........................
Oilphase
Schlumberger
Dyce, Aberdeen
Scotland.
49 CFR 178.36 .........
11670
11924–M .......
RSPA–97–2744
Wrangler Corporation, Auburn, ME.
49 CFR
173.12(B)(2)(i).
11924
12475–M .......
RSPA–00–7484
Chemetall Foote Corporation, Kings
Mountain, NC.
49 CFR 173.181;
173.28(b)(2).
12475
12630–M .......
RSPA–01–8550
Chemetall GmbH,
Gesellschaft 59500
Douai, France.
49 CFR
172.102(a)(2) and
(c)(7)(ii).
12630
13179–M .......
RSPA–02–
14020.
Clean Harbors Environmental Services, Inc., Columbia, SC.
49 CFR 173.21;
173.308.
13179
VerDate jul<14>2003
13:45 Aug 17, 2005
Jkt 205001
PO 00000
Frm 00114
Fmt 4703
Sfmt 4703
10798
To modify the exemption to authorize an
additional proper shipping name for a Division 4.2 and Division 4.3 material
transported in 4BA240 and 4BW240 cylinders.
To modify the exemption to authorize the
transportation of additional Division 6.1
materials transported in a UN1A2 drum
inside a non-DOT specification metal
container.
To modify the exemption to authorize a revision to the 3M Steri-Gas Cartridge Return Procedures containing a Division 2.3
material transported in UN4G fiberboard
boxes.
To modify the exemption to authorize an
additional proper shipping name for the
Division 4.2 material transported in DOT
Specification tank cars
To modify the exemption to authorize the
use of an alternative specially designed
combination packaging for the transportation of numerous hazardous materials
by various modes.
To modify the exemption to authorize the
transportation of an additional Division
6.1 material in uninsulated DOT Specification 51 portable tanks.
To modify the exemption to authorize the
alternative use of a nickel-based precipitation hardenable alloy for the non-DOT
specification cylinder used for oil well
sampling.
To modify the exemption to authorize an
additional design type of the composite
intermediate bulk container (IBC) and a
change to the additional IBC drop test
requirements.
To modify the exemption to authorize an
additional proper shipping name for the
Division 4.2 and Division 4.3 material
transported in UN1A1 drums.
To modify the exemption to authorize an
addiitional proper shipping name for the
Division 4.2 material transported in DOT
Specification IM 101 portable tanks.
To modify the exemption to authorize the
use of an alternative shipping description
and hazard class for the Division 2.1 materials which are being transported to a
disposal facility.
E:\FR\FM\18AUN1.SGM
18AUN1
Federal Register / Vol. 70, No. 159 / Thursday, August 18, 2005 / Notices
[FR Doc. 05–16406 Filed 8–17–05; 8:45 am]
BILLING CODE 4909–60–M
DEPARTMENT OF TRANSPORTATION
Pipeline and Hazardous Materials
Safety Administration
Office of Hazardous Materials Safety;
Notice of Application for Exemptions
Pipeline and Hazardous
Materials Safety Administration, DOT.
ACTION: List of applications for
exemption
AGENCY:
In accordance with the
procedures governing the application
for, and the processing of, exemptions
from the Department of Transportation’s
Hazardous Material Regulations (49 CFR
SUMMARY:
Application
No.
Docket No.
part 107, subpart B), notice is hereby
given that the Office of Hazardous
Materials Safety has received the
application described herein. Each
mode of transportation for which a
particular exemption is requested is
indicated by a number in the ‘‘Nature of
Application’’ portion of the table below
as follows: 1—Motor vehicle, 2—Rail
freight, 3—Cargo vessel, 4—Cargo
aircraft only, 5—Passenger-carrying
aircraft.
Comments must be received on
or before September 19, 2005.
Address Comments to: Record Center,
Pipeline and Hazardous Materials Safety
Administration, U.S. Department of
Transportation, Washington, DC 20590.
Comments should refer to the
application number and be submitted in
triplicate. If Confirmation of receipt of
DATES:
Applicant
48629
comments is desired, include a selfaddressed stamped postcard showing
the exemption number.
FOR FURTHER INFORMATION CONTACT:
Copies of the applications are available
for inspection in the Records Center,
Nassif Building, 400 7th Street SW.,
Washington, DC or at https://
dms.dot.gov.
This notice of receipt of applications
for modification of exemption is
published in accordance with part 107
of the Federal hazardous materials
transportation law (49 U.S.C. 5117(b);
49 CFR 1.53(b)).
Issued in Washington, DC, on August 12,
2005.
R. Ryan Posten,
Exemptions Program Officer, Office of
Hazardous Materials Safety Exemptions &
Approvals.
Regulation(s) affected
Nature of exemption thereof
NEW EXEMPTION
14227–N ......
PHMSA–2005–
2206
Aluminum Tank Industries, Inc., Winter
Haven, FL.
49 CFR 177.834(h),
178.799.
14428–N ......
PHMSA–2005–
2206
Goodrich Corporation,
Colorado Springs, CO.
49 CFR 173.301(f). ..........
14229–N ......
PHMSA–2005–
2206
Senex Explosives, Inc.,
Cuddy, PA.
49 CFR 17.835, 177.823,
and 177.848.
14230–N ......
PHMSA–2005–
2211
Epichem, Inc., Haverhill,
MA.
49 CFR 173.302a ............
[FR Doc. 05–16407 Filed 8–17–05; 8:45 am]
BILLING CODE 4909–60–M
DEPARTMENT OF THE TREASURY
August 11, 2005.
The Department of Treasury has
submitted the following public
information collection requirement(s) to
OMB for review and clearance under the
Paperwork Reduction Act of 1995,
Public Law 104–13. Copies of the
submission(s) may be obtained by
calling the Treasury Bureau Clearance
Officer listed. Comments regarding this
information collection should be
addressed to the OMB reviewer listed
and to the Treasury Department
Clearance Officer, Department of the
Treasury, Room 11000, 1750
16:36 Aug 17, 2005
Jkt 205001
Pennsylvania Avenue, NW.,
Washington, DC 20220.
DATES: Written comments should be
received on or before September 19,
2005, to be assured of consideration.
Internal Revenue Service (IRS)
Submission for OMB Review;
Comment Request
VerDate jul<14>2003
To authorize the manufacture, mark, sale, and use
of 50 gallon to 105 gallon refueling tanks containing certain Class 3 liquids which will be discharged without removal from the motor vehicle.
(mode 1)
To authorize the transportation in commerce of certain DOT Specification 3A and 3AA cylinders containing compressed oxygen without a pressure relief device. (modes 1, 4, 5)
To authorize the transportation in commerce of certain 1.4 and 1.5 explosives with Class 3 and Division 5.1 materials without meeting certain segregation requirements.
To authorize the one-time transportation in commerce of non-DOT specification cylinders containing Dichlorosilane to an ocean shipment consolidation facility and/or port. (modes 1, 3)
OMB Number: 1545–0090.
Form Number: IRS Form 1040–SS,
1040–PR and Anejo H–PR.
Type of Review: Extension.
Title: Form 1044–SS and 1040–PR is
used by self-employed individuals to
figure and report self-employment tax
and is also used by bona-fide residents
of Puerto Rico to claim the additional
child tax credit.
Description: Form 1040–SS (Virgin
Islands, Guam, American Samoa, and
the Northern Marina Islands) and 1040–
PR (Puerto Rico) are used by selfemployed individuals to figure and
report self-employment tax under IRC
chapter 2 of Subtitle A and provide
PO 00000
Frm 00115
Fmt 4703
Sfmt 4703
credit to the taxpayer’s social security
account. Anejo H–PR is used to
compute household employment taxes.
Form 1040–SS and Form 1040–PR are
also used by bona-fide residents of
Puerto Rico to claim the additional
child tax credit.
Respondents: Business and other forprofit, individuals or households and
farms.
Estimated Total Burden Hours:
2,762,588 hours.
OMB Number: 1545–1398.
Form Number: IRS Form 9620.
Type of Review: Extension.
Title: Race and National Origin
Identification.
Description: Form 9620 is used to
collect race and national origin data on
all IRS employees and new hires. The
information is used to insure that
agency personnel practices meet the
requirements of Federal law.
E:\FR\FM\18AUN1.SGM
18AUN1
]]>Agencies
[Federal Register Volume 70, Number 159 (Thursday, August 18, 2005)]
[Notices]
[Pages 48627-48629]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 05-16406]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Pipeline and Hazardous Materials Safety Administration Office of
Hazardous Materials Safety
Notice of Applications for Modification of Exemption
AGENCY: Pipeline and Hazardous Materials Safety Administration, DOT.
ACTION: List of applications for modification of exemption.
-----------------------------------------------------------------------
SUMMARY: In accordance with the procedures governing the application
for, and the processing of, exemptions from the Department of
Transportation's Hazardous Material Regulations (49 CFR part 107,
subpart B), notice is hereby given that the Office of Hazardous
Materials Safety has received the application described herein. This
notice is abbreviated to expedite docketing and public notice. Because
the sections affected, modes of transportation, and the nature of
application have been shown in earlier Federal Register publications,
they are not repeated here. Request of modifications of exemptions
(e.g. to
[[Page 48628]]
provide for additional hazardous materials, packaging design changes,
additional mode of transportation, etc.) are described in footnotes to
the application number. Application numbers with the suffix ``M''
demote a modification request. There applications have been separated
from the new application for exemption to facilitate processing.
DATES: Comments must be received on or before September 2, 2005.
Address Comments To: Record Center, Pipeline and Hazardous
Materials Safety Administration, U.S. Department of Transportation,
Washington, DC 20590.
Comments should refer to the application number and be submitted in
triplicate. If Confirmation of receipt of comments is desired, include
a self-addressed stamped postcard showing the exemption number.
FOR FURTHER INFORMATION CONTACT: Copies of the applications are
available for inspection in the Records Center, Nassif Building, 400
7th Street SW., Washington DC or at https://dms.dot.gov.
This notice of receipt of applications for modification of
exemption is published in accordance with Part 107 of the Federal
hazardous materials transportation law (49 U.S.C. 5117(b); 49 CFR
1.53(b)).
Issued in Washington, DC, on August 12, 2005.
R. Ryan Posten,
Exemptions Program Officer, Office of Hazardous Materials Exemptions &
Approvals.
----------------------------------------------------------------------------------------------------------------
Regulation(s) Modification Nature of exemption
Application No. Docket No. Applicant affected of exemption thereof
----------------------------------------------------------------------------------------------------------------
MODIFICATION EXEMPTIONS
----------------------------------------------------------------------------------------------------------------
4661-M........... ..................... Chemtell Foote 49 CFR 180.205. 4661 To modify the
Corporation, exemption to
Kings authorize an
Mountain, NC. additional proper
shipping name for a
Division 4.2 and
Division 4.3
material
transported in
4BA240 and 4BW240
cylinders.
10048-M.......... ..................... Epichem, Inc., 49 CFR 173.181; 10048 To modify the
Haverhill, MA. 173.187; exemption to
173.201, 202, authorize the
211, 212, 226, transportation of
227. additional Division
6.1 materials
transported in a
UN1A2 drum inside a
non-DOT
specification metal
container.
10695-M.......... ..................... 3M Company, St. 49 CFR 172.101; 10695 To modify the
Paul, MN. 172.504; exemption to
172.505(a); authorize a
173.323; revision to the 3M
174.81; Steri-Gas Cartridge
176.84; Return Procedures
177.848. containing a
Division 2.3
material
transported in UN4G
fiberboard boxes.
10798-M.......... ..................... Chemetall Foote 49 CFR 10798 To modify the
Corporation, 174.67(i),(j). exemption to
Kings authorize an
Mountain, NC. additional proper
shipping name for
the Division 4.2
material
transported in DOT
Specification tank
cars
10962-........... ..................... ICC The 49 CFR Part 10962 To modify the
Compliance 172, Subparts exemption to
Center, E, F; Part authorize the use
Niagara Falls, 177, Subpart C. of an alternative
NY. specially designed
combination
packaging for the
transportation of
numerous hazardous
materials by
various modes.
11318-M.......... ..................... Akzo Mobel 49 CFR 172.101 11318 To modify the
Chemicals, Special exemption to
Inc., Chicago, Provision B14. authorize the
IL. transportation of
an additional
Division 6.1
material in
uninsulated DOT
Specification 51
portable tanks.
11670-M.......... ..................... Oilphase 49 CFR 178.36.. 11670 To modify the
Schlumberger exemption to
Dyce, Aberdeen authorize the
Scotland. alternative use of
a nickel-based
precipitation
hardenable alloy
for the non-DOT
specification
cylinder used for
oil well sampling.
11924-M.......... RSPA-97-2744......... Wrangler 49 CFR 11924 To modify the
Corporation, 173.12(B)(2)(i exemption to
Auburn, ME. ). authorize an
additional design
type of the
composite
intermediate bulk
container (IBC) and
a change to the
additional IBC drop
test requirements.
12475-M.......... RSPA-00-7484......... Chemetall Foote 49 CFR 173.181; 12475 To modify the
Corporation, 173.28(b)(2). exemption to
Kings authorize an
Mountain, NC. additional proper
shipping name for
the Division 4.2
and Division 4.3
material
transported in
UN1A1 drums.
12630-M.......... RSPA-01-8550......... Chemetall GmbH, 49 CFR 12630 To modify the
Gesellschaft 172.102(a)(2) exemption to
59500 Douai, and (c)(7)(ii). authorize an
France. addiitional proper
shipping name for
the Division 4.2
material
transported in DOT
Specification IM
101 portable tanks.
13179-M.......... RSPA-02-14020........ Clean Harbors 49 CFR 173.21; 13179 To modify the
Environmental 173.308. exemption to
Services, authorize the use
Inc., of an alternative
Columbia, SC. shipping
description and
hazard class for
the Division 2.1
materials which are
being transported
to a disposal
facility.
----------------------------------------------------------------------------------------------------------------
[[Page 48629]]
[FR Doc. 05-16406 Filed 8-17-05; 8:45 am]
BILLING CODE 4909-60-M
