Airworthiness Directives; Boeing Model 747-100, -100B, -100B SUD, -200B, -200C, -300, -400, and -400D Series Airplanes; and Model 747SR Series Airplanes, 28800-28803 [05-9876]

Download as PDF 28800 Federal Register / Vol. 70, No. 96 / Thursday, May 19, 2005 / Rules and Regulations Actions Accomplished According to Previous Issue of Service Bulletin (c) Actions accomplished before the effective date of this AD according to Boeing Service Bulletin 777–57A0040, Revision 1, dated July 10, 2003, are considered acceptable for compliance with the corresponding action specified in this AD. Alternative Methods of Compliance (d) In accordance with 14 CFR 39.19, the Manager, Seattle ACO, is authorized to approve alternative methods of compliance for this AD. Incorporation by Reference (e) Unless otherwise specified in this AD, the actions shall be done in accordance with Boeing Service Bulletin 777–57A0040, Revision 2, dated February 24, 2005. This incorporation by reference was approved by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. To get copies of the service information, go to Boeing Commercial Airplanes, P.O. Box 3707, Seattle, Washington 98124–2207. Copies may be inspected at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington; or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call (202) 741–6030, or go to: https://www.archives.gov/federal_register/ code_of_federal_regulations/ ibr_locations.html. Effective Date (f) This amendment becomes effective on June 23, 2005. Issued in Renton, Washington, on May 9, 2005. Jeffrey E. Duven, Acting Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. 05–9875 Filed 5–18–05; 8:45 am] BILLING CODE 4910–13–P DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2004–19796; Directorate Identifier 2004–NM–61–AD; Amendment 39– 14095; AD 2005–10–18] RIN 2120–AA64 Airworthiness Directives; Boeing Model 747–100, –100B, –100B SUD, –200B, –200C, –300, –400, and –400D Series Airplanes; and Model 747SR Series Airplanes Federal Aviation Administration (FAA), Department of Transportation (DOT). ACTION: Final rule. AGENCY: SUMMARY: The FAA is superseding an existing airworthiness directive (AD), VerDate jul<14>2003 15:30 May 18, 2005 Jkt 205001 which applies to certain Boeing Model 747 series airplanes. That AD currently requires a one-time inspection to determine the material type of the stop support fittings of the main entry doors (MEDs). That AD also currently requires repetitive detailed inspections to detect cracks of certain stop support fittings of the MEDs, and replacement of any cracked stop support fitting with a certain new stop support fitting. This new AD adds new inspections, and replacement if necessary, of the stop support fittings of MED 3, and adds airplanes to the applicability. This AD is prompted by reports of MED 3 having certain stop support fittings that are susceptible to stress corrosion cracking. We are issuing this AD to detect and correct stress corrosion cracking of the stop support fittings of the MEDs, which could result in damage to the adjacent forward edge frame of the door and consequent loss of a MED and rapid decompression of the airplane. DATES: This AD becomes effective June 23, 2005. The incorporation by reference of Boeing Service Bulletin 747–53–2358, Revision 1, dated April 19, 2001; and Boeing Special Attention Service Bulletin 747–53–2485, dated January 8, 2004; as listed in the AD, is approved by the Director of the Federal Register as of June 23, 2005. On January 25, 1999 (63 FR 70316, December 21, 1998), the Director of the Federal Register approved the incorporation by reference of Boeing Service Bulletin 747–53–2358, dated August 26, 1993. ADDRESSES: For service information identified in this AD, contact Boeing Commercial Airplanes, P.O. Box 3707, Seattle, Washington 98124–2207. Docket: The AD docket contains the proposed AD, comments, and any final disposition. You can examine the AD docket on the Internet at https:// dms.dot.gov, or in person at the Docket Management Facility office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The Docket Management Facility office (telephone (800) 647–5227) is located on the plaza level of the Nassif Building at the U.S. Department of Transportation, 400 Seventh Street, SW., room PL–401, Washington, DC. This docket number is FAA–2004–19796; the directorate identifier for this docket is 2004–NM– 61–AD. FOR FURTHER INFORMATION CONTACT: Ivan Li, Aerospace Engineer, Airframe Branch, ANM–120S, FAA, Seattle Aircraft Certification Office, 1601 Lind Avenue, SW., Renton, Washington PO 00000 Frm 00026 Fmt 4700 Sfmt 4700 98055–4056; telephone (425) 917–6437; fax (425) 917–6590. SUPPLEMENTARY INFORMATION: The FAA proposed to amend part 39 of the Federal Aviation Regulations (14 CFR Part 39) with an AD to supersede AD 98–26–13, amendment 39–10954 (63 FR 70316, December 21, 1998). The existing AD applies to certain Boeing Model 747 series airplanes. The proposed AD was published in the Federal Register on December 3, 2004 (69 FR 70204), to continue to require a one-time inspection to determine the material type of the stop support fittings of the main entry doors (MEDs), repetitive detailed inspections to detect cracks of certain stop support fittings of the MEDs, and replacement of any cracked stop support fitting with a certain new stop support fitting. The proposed AD also adds new inspections, and replacement if necessary, of the stop support fittings of MED 3, and adds airplanes to the applicability. Comments We provided the public the opportunity to participate in the development of this AD. We have considered the comments that have been submitted on the proposed AD. Concur With the Proposed AD One commenter concurs with the proposed AD and has no additional comments. Request To Add Provision to State Operators Are Not in Violation of Proposed AD One commenter requests that a provision be added to the proposed AD to state that operators ‘‘are not in violation of paragraphs (f) and (g)’’ of the proposed AD if it is determined that some of the fittings replaced in accordance with paragraphs (f) and (g) were made of the incorrect material. The commenter states that paragraphs (f) and (g) of the proposed AD specify that fittings be replaced with fittings made of the correct material. The commenter also states that paragraph (h) of the proposed AD specifies that replaced fittings be inspected to determine if the fittings are made of the correct material. Therefore, if an operator accomplishes the inspection specified in paragraph (h) of the proposed AD and finds fittings made of the incorrect material, then the operator would be in violation of the paragraphs (f) and (g) of the proposed AD. We agree that an operator is not in violation of paragraphs (f), (g), and (l) of the final rule if fittings were replaced in good faith with fittings supplied by Boeing that are determined to be made E:\FR\FM\19MYR1.SGM 19MYR1 Federal Register / Vol. 70, No. 96 / Thursday, May 19, 2005 / Rules and Regulations of the incorrect material during the inspection required by paragraph (h) of the final rule. As stated in the preamble of the proposed AD, ‘‘the new stop support fittings supplied by Boeing as the replacement fitting for MED 3 may not have been made from the correct material type.’’ Thus, operators may have unknowingly installed replacement fittings made of the incorrect material and should not be penalized if the inspection required by paragraph (h) of the final rule determines there are fittings made of the incorrect material. However, operators must then do the applicable inspections/replacement required by paragraph (k) of the final rule. We have not changed the final rule in this regard. Request To Remove Requirement to Remove Foam and Inspect/Drill Drain Hole One commenter requests that the actions specified in Boeing Special Attention Service Bulletin 747–53–2485 (cited in the proposed AD as the appropriate source of service information for accomplishing the proposed inspections) to remove foam and inspect/drill drain holes be removed from the requirements of the proposed AD. The commenter states it has established that the foam need not be removed to do the conductivity test. The commenter also states that ‘‘this has been acknowledged in the Boeing telex SR 1–48729376/Message No 1–TETPP.’’ We agree that removal of the foam and inspecting/drilling drain holes should not be required. Paragraphs (h) and (i) of the proposed AD specify only that an inspection to determine material type of the stop support fittings be done in accordance with Boeing Special Attention Service Bulletin 747–53–2485 and paragraph (k) of the proposed AD specifies that an inspection for cracks of the stop support fittings be done in accordance with the service bulletin. Removing foam and inspecting/drilling drain holes are not a part of these inspections and are not part of the corrective action needed to address the 28801 paragraph (h)(1) of the proposed AD be revised to be applicable only to fittings that were replaced before the effective date of AD 98–26–13. The commenter notes that paragraph (c) of AD 98–26– 13 mandates that no person shall install a stop fitting made from either 7079– T651 or 7075–T651 material on any airplane as of January 25, 1999 (the effective date of AD 98–26–13). The commenter concludes that all stop support fittings installed after the effective date of AD 98–26–13 are required to be made from 7075–T73 or 7050–T451 aluminum. We disagree with the request to revise the one-time HFEC inspection. As stated in the preamble of the proposed AD, ‘‘the new stop support fittings supplied by Boeing as the replacement fitting for MED 3 may not have been made from the correct material type.’’ Therefore, operators complying with AD 98–26–13 could have unknowingly installed support fittings supplied by Boeing that were made of the incorrect material (7079–T651 or 7075–T651 material). Because of this possibility, the final rule requires a one-time HFEC inspection of any stop support fittings that were replaced before the effective date of the final rule. We have not changed the final rule in this regard. identified unsafe condition (stress corrosion cracking of the stop support fittings of the main entry doors). Because removing foam and inspecting/ drilling drain holes are described in the Accomplishment Instructions of the service bulletin, we have added Note 2 to the final rule for clarification that these actions are not required when doing any inspection required by paragraphs (h), (i), and (k) of the final rule. Request for Credit for Inspection One commenter has no technical objections to the proposed AD. However, the commenter requests that if a stop support fitting was replaced before the effective date of the proposed AD and a conductivity test per Boeing 747 Nondestructive Test Manual D6 7170, Part 6, Chapter 51–00–00, Figure 20, was done during the replacement, then the one-time high frequency eddy current (HFEC) inspection specified in paragraph (h)(1) of the proposed AD need not be required. We agree that, for any stop support fitting replaced before the effective date of the final rule on which a conductivity test per Boeing 747 Nondestructive Test Manual D6–7170, Part 6, Chapter 51– 00–00, Figure 20, has been done, then the one-time HFEC inspection specified in paragraph (h)(1) of the final rule does not need to be done. The conductivity test per Boeing 747 Nondestructive Test Manual D6–7170, Part 6, Chapter 51– 00–00, Figure 20, is the HFEC inspection specified in the final rule. The final rule specifies that the HFEC be done in accordance with Boeing Special Attention Service Bulletin 747–53– 2485, and the service bulletin refers to Boeing 747 Nondestructive Test Manual D6–7170, Part 6, Chapter 51–00–00, Figure 20. Paragraph (e) of the final rule gives credit for actions done before the effective date of the final rule. We have not changed the final rule in this regard. Conclusion We have carefully reviewed the available data, including the comments that have been submitted, and determined that air safety and the public interest require adopting the AD with the change described previously. We have determined that this change will neither increase the economic burden on any operator nor increase the scope of the AD. Costs of Compliance There are about 814 airplanes of the affected design in the worldwide fleet. There are about 119 airplanes of U.S. registry that will be affected by this AD. The following table provides the estimated costs for U.S. operators to comply with this AD. Request To Revise One-Time HFEC Inspection One commenter requests that the onetime HFEC inspection specified in ESTIMATED COSTS Work hours Action HFEC Inspection (required by AD 98–26–13) ................................................................ Detailed Inspection as applicable (required by AD 98–26–13) ....................................... Optional Terminating Action (specified in AD 98–26–13) ............................................... Detailed Inspection and HFEC Inspection as applicable (new action) ........................... Replacement as applicable (new action) ........................................................................ 1 2 124 3 120 Average labor rate per hour $65 65 65 65 65 1 None. VerDate jul<14>2003 15:30 May 18, 2005 Jkt 205001 PO 00000 Frm 00027 Fmt 4700 Sfmt 4700 E:\FR\FM\19MYR1.SGM 19MYR1 Parts (1) (1) $13,000 (1) 17,724 Cost per door $65 130 21,060 195 25,524 28802 Federal Register / Vol. 70, No. 96 / Thursday, May 19, 2005 / Rules and Regulations Authority for This Rulemaking Title 49 of the United States Code specifies the FAA’s authority to issue rules on aviation safety. Subtitle I, Section 106, describes the authority of the FAA Administrator. Subtitle VII, Aviation Programs, describes in more detail the scope of the Agency’s authority. We are issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701, ‘‘General requirements.’’ Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. Regulatory Findings We have determined that this AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government. For the reasons discussed above, I certify that this AD: (1) Is not a ‘‘significant regulatory action’’ under Executive Order 12866; (2) Is not a ‘‘significant rule’’ under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and (3) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. We prepared a regulatory evaluation of the estimated costs to comply with this AD. See the ADDRESSES section for a location to examine the regulatory evaluation. List of Subjects in 14 CFR Part 39 Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety. Adoption of the Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows: I PART 39—AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows: I VerDate jul<14>2003 15:30 May 18, 2005 Jkt 205001 Authority: 49 U.S.C. 106(g), 40113, 44701. § 39.13 [Amended] 2. The FAA amends § 39.13 by removing amendment 39–10954 (63 FR 70316, December 21, 1998), and by adding the following new airworthiness directive (AD): I 2005–10–18 Boeing: Amendment 39–14095. Docket No. FAA–2004–19796; Directorate Identifier 2004–NM–61–AD. Effective Date (a) This AD becomes effective June 23, 2005. Affected ADs (b) This AD supersedes AD 98–26–13, amendment 39–10954. Applicability (c) This AD applies to Boeing Model 747– 100, –100B, –100B SUD, –200B, –200C, –300, –400, and –400D series airplanes; and Model 747SR series airplanes; having line numbers 1 through 1301 inclusive; certificated in any category. Unsafe Condition (d) This AD was prompted by reports of main entry door (MED) 3 having certain stop support fittings that are susceptible to stress corrosion cracking. We are issuing this AD to detect and correct stress corrosion cracking of the stop support fittings of the MEDs, which could result in damage to the adjacent forward edge frame of the door and consequent loss of a MED and rapid decompression of the airplane. Compliance (e) You are responsible for having the actions required by this AD performed within the compliance times specified, unless the actions have already been done. Requirements of AD 98–26–13 Inspections and Corrective Action (f) For Model 747–100, –100B, –100B SUD, –200, –200B, –200C, –300, –400, and 747SR series airplanes having line numbers 1 through 830 inclusive: Within 18 months after January 25, 1999 (the effective date of AD 98–26–13, amendment 39–10954), perform a high frequency eddy current (HFEC) inspection to determine the material type of the stop support fittings of the MEDs, in accordance with the Accomplishment Instructions of Boeing Service Bulletin 747– 53–2358, dated August 26, 1993; or Boeing Service Bulletin 747–53–2358, Revision 1, dated April 19, 2001. Perform the inspection only at those locations where the material type of the stop support fittings is unknown, as specified in Figure 3, Table 1, of either service bulletin. As of the effective date of this AD, do the actions in accordance with Boeing Service Bulletin 747–53–2358, Revision 1, dated April 19, 2001. (1) If the fitting is made from 7075–T73 or 7050–T7451 material, no further action is required by this AD for that fitting; however, the requirements of paragraph (l) of this AD still apply. (2) If the fitting is not made from 7075–T73 or 7050–T7451 material, before further flight, PO 00000 Frm 00028 Fmt 4700 Sfmt 4700 perform a detailed inspection to detect cracks of the stop support fitting of the MEDs, in accordance with the applicable service bulletin. Note 1: For the purposes of this AD, a detailed inspection is ‘‘an intensive examination of a specific item, installation, or assembly to detect damage, failure, or irregularity. Available lighting is normally supplemented with a direct source of good lighting at an intensity deemed appropriate. Inspection aids such as mirrors magnifying lenses, etc. may be necessary. Surface cleaning and elaborate procedures may be required.’’ (i) If no crack is detected, repeat the detailed inspection thereafter at intervals not to exceed 36 months or 2,000 flight cycles, whichever occurs first. (ii) If any crack is detected, before further flight, replace the fitting with a stop support fitting made from 7075–T73 or 7050–T7451 material, in accordance with the applicable service bulletin. (g) For Model 747–100, –100B, –100B SUD, –200, –200B, –200C, –300, –400, and 747SR series airplanes having line numbers 1 through 830 inclusive: Replacement of the stop support fitting of the MEDs with a stop support fitting made from 7075–T73 material, in accordance with Boeing Service Bulletin 747–53–2358, dated August 26, 1993; or replacement with a stop support fitting made from 7075–T73 or 7050–T7451 material, in accordance with Boeing Service Bulletin 747–53–2358, Revision 1, dated April 19, 2001; constitutes terminating action for the repetitive inspection requirements of paragraph (f) of this AD for the replaced fitting. As of the effective date of this AD, only Boeing Service Bulletin 747–53–2358, Revision 1, dated April 19, 2001, may be used. New Requirements of This AD Note 2: Operators are not required to remove foam and inspect/drill drain holes as specified in Paragraph 3.B.1.e. and the Notes of the Accomplishment Instructions of Boeing Special Attention Service Bulletin 747–53–2485, dated January 8, 2004, when doing any inspection required by paragraphs (h), (i), and (k) of this AD. Inspection for Material Type (h) For Model 747–100, –100B, –100B SUD, –200B, –200C, –300, –400, and –400D series airplanes, and Model 747SR series airplanes, having line numbers 1 through 830 inclusive on which the actions specified in the Accomplishment Instructions of Boeing Service Bulletin 747–53–2358, dated August 26, 1993; or Boeing Service Bulletin 747–53– 2358, Revision 1, dated April 19, 2001; have been done: Do the inspection specified in paragraph (h)(1) or (h)(2) of this AD, as applicable, at the time specified. (1) Except as provided by paragraph (h)(2) of this AD, if any stop support fitting, 2L through 6L and 2R through 6R, of MED 3, was replaced before the effective date of this AD: Perform a one-time HFEC inspection to determine the material type of the stop support fittings of MED 3 that were replaced, in accordance with the Accomplishment Instructions of Boeing Special Attention E:\FR\FM\19MYR1.SGM 19MYR1 28803 Federal Register / Vol. 70, No. 96 / Thursday, May 19, 2005 / Rules and Regulations Service Bulletin 747–53–2485, dated January 8, 2004, at the later of the times specified in paragraphs (h)(1)(i) and (h)(1)(ii) of this AD. (i) Within 72 months after the stop support fitting of MED 3 was replaced. (ii) Within 18 months after the effective date of this AD. (2) If any stop support fitting, 2L through 6L and 2R through 6R, of MED 3, cannot be determined conclusively by reviewing airplane maintenance records that the fitting was not replaced, within 18 months after the effective date of this AD, perform a one-time HFEC inspection to determine the material type of the stop support fitting, in accordance with the Accomplishment Instructions of Boeing Special Attention Service Bulletin 747–53–2485, dated January 8, 2004. (i) For airplanes having line numbers 831 through 1301 inclusive: At the later of the times specified in paragraphs (i)(1) and (i)(2) of this AD, perform a one-time HFEC inspection to determine the material type of the stop support fittings of MED 3 in accordance with the Accomplishment Instructions of Boeing Special Attention Service Bulletin 747–53–2485, dated January 8, 2004. (1) Before 72 months since the date of issuance of the original Airworthiness Certificate or the date of issuance of the original Export Certificate of Airworthiness. (2) Within 18 months after the effective date of this AD. No Further Action (j) If, during any HFEC inspection required by paragraph (h) or (i) of this AD, any fitting is found to be made of 7075–T73 or 7050– T7451 material, no further action is required by this AD for that fitting; however, paragraph (l) of this AD still applies. Initial and Repetitive Inspections for Cracking and Corrective Action (k) If, during any HFEC inspection required by paragraph (h) or (i) of this AD, any fitting is found not to be made of 7075–T73 or 7050–T7451 material, before further flight, perform a detailed inspection for cracks of the fitting in accordance with the Accomplishment Instructions of Boeing Special Attention Service Bulletin 747–53– 2485, dated January 8, 2004. (1) If no crack is detected, repeat the detailed inspection specified in paragraph (k) of this AD thereafter at intervals not to exceed 36 months or 2,000 flight cycles, whichever comes first. Doing the replacement specified in paragraph (k)(2) of this AD ends the repetitive inspections for the replaced fitting. (2) If any crack is detected, before further flight, replace the fitting with a fitting made of 7075–T73 or 7050–T7451 material in accordance with the Accomplishment Instructions of Boeing Special Attention Service Bulletin 747–53–2485, dated January 8, 2004. No further action is required by this AD for that fitting; however, paragraph (l) of this AD still applies. Parts Installation (l) As of the date specified in paragraph (l)(1) or (l)(2) of this AD, as applicable, no person shall install on any airplane a stop support fitting of the MEDs made from either 7079–T651 or 7075–T651 material. (1) For airplanes having line numbers 1 through 830 inclusive: As of January 25, 1999. (2) For airplanes having line numbers 831 through 1301 inclusive: As of the effective date of this AD. Alternative Methods of Compliance (AMOCs) (m)(1) The Manager, Seattle Aircraft Certification Office (ACO), FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. (2) AMOCs, approved previously per AD 98–26–13, amendment 39–10954, are approved as AMOCs with paragraph (f) or (g) of this AD, as applicable. However, any stop support fitting, 2L through 6L and 2R through 6R, of MED 3 that was replaced is still required to be inspected as required in paragraph (h) of this AD. Material Incorporated by Reference (n) You must use the service information that is specified in Table 1 of this AD to perform the actions that are required by this AD, unless the AD specifies otherwise. (1) The Director of the Federal Register approves the incorporation by reference of Boeing Service Bulletin 747–53–2358, Revision 1, dated April 19, 2001; and Boeing Special Attention Service Bulletin 747–53– 2485, dated January 8, 2004; in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. (2) The Director of the Federal Register previously approved the incorporation by reference of Boeing Service Bulletin 747–53– 2358, dated August 26, 1993, as of January 25, 1999 (63 FR 70316, December 21, 1998). (3) To get copies of the service information, go to Boeing Commercial Airplanes, P.O. Box 3707, Seattle, Washington 98124–2207. To view the AD docket, go to the Docket Management Facility, U.S. Department of Transportation, 400 Seventh Street SW., room PL–401, Nassif Building, Washington, DC. To review copies of the service information, go to the National Archives and Records Administration (NARA). For information on the availability of this material at the NARA, call (202) 741–6030, or go to https://www.archives.gov/ federal_register/code_of_federal_regulations/ ibr_locations.html. TABLE 1.—MATERIAL INCORPORATED BY REFERENCE Service bulletin Revision level Boeing Service Bulletin 747–53–2358 .................................................................................................... Boeing Service Bulletin 747–53–2358 .................................................................................................... Boeing Special Attention Service Bulletin 747–53–2485 ....................................................................... Original ............... 1 ......................... Original ............... Issued in Renton, Washington, on May 9, 2005. Jeffrey E. Duven, Acting Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. 05–9876 Filed 5–18–05; 8:45 am] BILLING CODE 4910–13–P DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2004–19538; Directorate Identifier 2003–NM–99–AD; Amendment 39– 14098; AD 2005–10–21] RIN 2120–AA64 Airworthiness Directives; Boeing Model 747 Airplanes Federal Aviation Administration (FAA), Department of Transportation (DOT). ACTION: Final rule. AGENCY: VerDate jul<14>2003 15:30 May 18, 2005 Jkt 205001 PO 00000 Frm 00029 Fmt 4700 Sfmt 4700 Date August 26, 1993. April 19, 2001. January 8, 2004. SUMMARY: The FAA is superseding an existing airworthiness directive (AD), which applies to certain Boeing Model 747 airplanes. That AD currently requires inspections to detect cracks in the front spar pressure bulkhead chord, and repair if necessary. This new AD requires repetitive high frequency eddy current (HFEC) inspections of the body station (BS) 1000 bulkhead chord for cracks, repetitive detailed inspections of the bathtub fittings, if installed, for cracks, and corrective action if necessary. Initiation of the new inspections ends the inspections of the existing AD. This AD also revises the applicability of the existing AD to include additional airplanes. This AD is E:\FR\FM\19MYR1.SGM 19MYR1

Agencies

[Federal Register Volume 70, Number 96 (Thursday, May 19, 2005)]
[Rules and Regulations]
[Pages 28800-28803]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 05-9876]

-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2004-19796; Directorate Identifier 2004-NM-61-AD;
Amendment 39-14095; AD 2005-10-18]
RIN 2120-AA64

Airworthiness Directives; Boeing Model 747-100, -100B, -100B SUD,
-200B, -200C, -300, -400, and -400D Series Airplanes; and Model 747SR
Series Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of
Transportation (DOT).

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: The FAA is superseding an existing airworthiness directive
(AD), which applies to certain Boeing Model 747 series airplanes. That
AD currently requires a one-time inspection to determine the material
type of the stop support fittings of the main entry doors (MEDs). That
AD also currently requires repetitive detailed inspections to detect
cracks of certain stop support fittings of the MEDs, and replacement of
any cracked stop support fitting with a certain new stop support
fitting. This new AD adds new inspections, and replacement if
necessary, of the stop support fittings of MED 3, and adds airplanes to
the applicability. This AD is prompted by reports of MED 3 having
certain stop support fittings that are susceptible to stress corrosion
cracking. We are issuing this AD to detect and correct stress corrosion
cracking of the stop support fittings of the MEDs, which could result
in damage to the adjacent forward edge frame of the door and consequent
loss of a MED and rapid decompression of the airplane.

DATES: This AD becomes effective June 23, 2005.
The incorporation by reference of Boeing Service Bulletin 747-53-
2358, Revision 1, dated April 19, 2001; and Boeing Special Attention
Service Bulletin 747-53-2485, dated January 8, 2004; as listed in the
AD, is approved by the Director of the Federal Register as of June 23,
2005.
On January 25, 1999 (63 FR 70316, December 21, 1998), the Director
of the Federal Register approved the incorporation by reference of
Boeing Service Bulletin 747-53-2358, dated August 26, 1993.

ADDRESSES: For service information identified in this AD, contact
Boeing Commercial Airplanes, P.O. Box 3707, Seattle, Washington 98124-
2207.
Docket: The AD docket contains the proposed AD, comments, and any
final disposition. You can examine the AD docket on the Internet at
https://dms.dot.gov, or in person at the Docket Management Facility
office between 9 a.m. and 5 p.m., Monday through Friday, except Federal
holidays. The Docket Management Facility office (telephone (800) 647-
5227) is located on the plaza level of the Nassif Building at the U.S.
Department of Transportation, 400 Seventh Street, SW., room PL-401,
Washington, DC. This docket number is FAA-2004-19796; the directorate
identifier for this docket is 2004-NM-61-AD.

FOR FURTHER INFORMATION CONTACT: Ivan Li, Aerospace Engineer, Airframe
Branch, ANM-120S, FAA, Seattle Aircraft Certification Office, 1601 Lind
Avenue, SW., Renton, Washington 98055-4056; telephone (425) 917-6437;
fax (425) 917-6590.

SUPPLEMENTARY INFORMATION: The FAA proposed to amend part 39 of the
Federal Aviation Regulations (14 CFR Part 39) with an AD to supersede
AD 98-26-13, amendment 39-10954 (63 FR 70316, December 21, 1998). The
existing AD applies to certain Boeing Model 747 series airplanes. The
proposed AD was published in the Federal Register on December 3, 2004
(69 FR 70204), to continue to require a one-time inspection to
determine the material type of the stop support fittings of the main
entry doors (MEDs), repetitive detailed inspections to detect cracks of
certain stop support fittings of the MEDs, and replacement of any
cracked stop support fitting with a certain new stop support fitting.
The proposed AD also adds new inspections, and replacement if
necessary, of the stop support fittings of MED 3, and adds airplanes to
the applicability.

Comments

We provided the public the opportunity to participate in the
development of this AD. We have considered the comments that have been
submitted on the proposed AD.

Concur With the Proposed AD

One commenter concurs with the proposed AD and has no additional
comments.

Request To Add Provision to State Operators Are Not in Violation of
Proposed AD

One commenter requests that a provision be added to the proposed AD
to state that operators ``are not in violation of paragraphs (f) and
(g)'' of the proposed AD if it is determined that some of the fittings
replaced in accordance with paragraphs (f) and (g) were made of the
incorrect material. The commenter states that paragraphs (f) and (g) of
the proposed AD specify that fittings be replaced with fittings made of
the correct material. The commenter also states that paragraph (h) of
the proposed AD specifies that replaced fittings be inspected to
determine if the fittings are made of the correct material. Therefore,
if an operator accomplishes the inspection specified in paragraph (h)
of the proposed AD and finds fittings made of the incorrect material,
then the operator would be in violation of the paragraphs (f) and (g)
of the proposed AD.
We agree that an operator is not in violation of paragraphs (f),
(g), and (l) of the final rule if fittings were replaced in good faith
with fittings supplied by Boeing that are determined to be made

[[Page 28801]]

of the incorrect material during the inspection required by paragraph
(h) of the final rule. As stated in the preamble of the proposed AD,
``the new stop support fittings supplied by Boeing as the replacement
fitting for MED 3 may not have been made from the correct material
type.'' Thus, operators may have unknowingly installed replacement
fittings made of the incorrect material and should not be penalized if
the inspection required by paragraph (h) of the final rule determines
there are fittings made of the incorrect material. However, operators
must then do the applicable inspections/replacement required by
paragraph (k) of the final rule. We have not changed the final rule in
this regard.

Request To Remove Requirement to Remove Foam and Inspect/Drill Drain
Hole

One commenter requests that the actions specified in Boeing Special
Attention Service Bulletin 747-53-2485 (cited in the proposed AD as the
appropriate source of service information for accomplishing the
proposed inspections) to remove foam and inspect/drill drain holes be
removed from the requirements of the proposed AD. The commenter states
it has established that the foam need not be removed to do the
conductivity test. The commenter also states that ``this has been
acknowledged in the Boeing telex SR 1-48729376/Message No 1-TETPP.''
We agree that removal of the foam and inspecting/drilling drain
holes should not be required. Paragraphs (h) and (i) of the proposed AD
specify only that an inspection to determine material type of the stop
support fittings be done in accordance with Boeing Special Attention
Service Bulletin 747-53-2485 and paragraph (k) of the proposed AD
specifies that an inspection for cracks of the stop support fittings be
done in accordance with the service bulletin. Removing foam and
inspecting/drilling drain holes are not a part of these inspections and
are not part of the corrective action needed to address the identified
unsafe condition (stress corrosion cracking of the stop support
fittings of the main entry doors). Because removing foam and
inspecting/drilling drain holes are described in the Accomplishment
Instructions of the service bulletin, we have added Note 2 to the final
rule for clarification that these actions are not required when doing
any inspection required by paragraphs (h), (i), and (k) of the final
rule.

Request for Credit for Inspection

One commenter has no technical objections to the proposed AD.
However, the commenter requests that if a stop support fitting was
replaced before the effective date of the proposed AD and a
conductivity test per Boeing 747 Nondestructive Test Manual D6 7170,
Part 6, Chapter 51-00-00, Figure 20, was done during the replacement,
then the one-time high frequency eddy current (HFEC) inspection
specified in paragraph (h)(1) of the proposed AD need not be required.
We agree that, for any stop support fitting replaced before the
effective date of the final rule on which a conductivity test per
Boeing 747 Nondestructive Test Manual D6-7170, Part 6, Chapter 51-00-
00, Figure 20, has been done, then the one-time HFEC inspection
specified in paragraph (h)(1) of the final rule does not need to be
done. The conductivity test per Boeing 747 Nondestructive Test Manual
D6-7170, Part 6, Chapter 51-00-00, Figure 20, is the HFEC inspection
specified in the final rule. The final rule specifies that the HFEC be
done in accordance with Boeing Special Attention Service Bulletin 747-
53-2485, and the service bulletin refers to Boeing 747 Nondestructive
Test Manual D6-7170, Part 6, Chapter 51-00-00, Figure 20. Paragraph (e)
of the final rule gives credit for actions done before the effective
date of the final rule. We have not changed the final rule in this
regard.

Request To Revise One-Time HFEC Inspection

One commenter requests that the one-time HFEC inspection specified
in paragraph (h)(1) of the proposed AD be revised to be applicable only
to fittings that were replaced before the effective date of AD 98-26-
13. The commenter notes that paragraph (c) of AD 98-26-13 mandates that
no person shall install a stop fitting made from either 7079-T651 or
7075-T651 material on any airplane as of January 25, 1999 (the
effective date of AD 98-26-13). The commenter concludes that all stop
support fittings installed after the effective date of AD 98-26-13 are
required to be made from 7075-T73 or 7050-T451 aluminum.
We disagree with the request to revise the one-time HFEC
inspection. As stated in the preamble of the proposed AD, ``the new
stop support fittings supplied by Boeing as the replacement fitting for
MED 3 may not have been made from the correct material type.''
Therefore, operators complying with AD 98-26-13 could have unknowingly
installed support fittings supplied by Boeing that were made of the
incorrect material (7079-T651 or 7075-T651 material). Because of this
possibility, the final rule requires a one-time HFEC inspection of any
stop support fittings that were replaced before the effective date of
the final rule. We have not changed the final rule in this regard.

Conclusion

We have carefully reviewed the available data, including the
comments that have been submitted, and determined that air safety and
the public interest require adopting the AD with the change described
previously. We have determined that this change will neither increase
the economic burden on any operator nor increase the scope of the AD.

Costs of Compliance

There are about 814 airplanes of the affected design in the
worldwide fleet. There are about 119 airplanes of U.S. registry that
will be affected by this AD. The following table provides the estimated
costs for U.S. operators to comply with this AD.

Estimated Costs
----------------------------------------------------------------------------------------------------------------
Average
Action Work hours labor rate Parts Cost per
per hour door
----------------------------------------------------------------------------------------------------------------
HFEC Inspection (required by AD 98-26-13)................... 1 $65 (\1\) $65
Detailed Inspection as applicable (required by AD 98-26-13). 2 65 (\1\) 130
Optional Terminating Action (specified in AD 98-26-13)...... 124 65 $13,000 21,060
Detailed Inspection and HFEC Inspection as applicable (new 3 65 (\1\) 195
action)....................................................
Replacement as applicable (new action)...................... 120 65 17,724 25,524
----------------------------------------------------------------------------------------------------------------
\1\ None.

[[Page 28802]]

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, Section 106, describes the
authority of the FAA Administrator. Subtitle VII, Aviation Programs,
describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701, ``General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.

Regulatory Findings

We have determined that this AD will not have federalism
implications under Executive Order 13132. This AD will not have a
substantial direct effect on the States, on the relationship between
the national government and the States, or on the distribution of power
and responsibilities among the various levels of government.
For the reasons discussed above, I certify that this AD:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866;
(2) Is not a ``significant rule'' under DOT Regulatory Policies and
Procedures (44 FR 11034, February 26, 1979); and
(3) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to
comply with this AD. See the ADDRESSES section for a location to
examine the regulatory evaluation.

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.

Adoption of the Amendment

0
Accordingly, under the authority delegated to me by the Administrator,
the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0
1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

Sec. 39.13 [Amended]

0
2. The FAA amends Sec. 39.13 by removing amendment 39-10954 (63 FR
70316, December 21, 1998), and by adding the following new
airworthiness directive (AD):

2005-10-18 Boeing: Amendment 39-14095. Docket No. FAA-2004-19796;
Directorate Identifier 2004-NM-61-AD.

Effective Date

(a) This AD becomes effective June 23, 2005.

Affected ADs

(b) This AD supersedes AD 98-26-13, amendment 39-10954.

Applicability

(c) This AD applies to Boeing Model 747-100, -100B, -100B SUD, -
200B, -200C, -300, -400, and -400D series airplanes; and Model 747SR
series airplanes; having line numbers 1 through 1301 inclusive;
certificated in any category.

Unsafe Condition

(d) This AD was prompted by reports of main entry door (MED) 3
having certain stop support fittings that are susceptible to stress
corrosion cracking. We are issuing this AD to detect and correct
stress corrosion cracking of the stop support fittings of the MEDs,
which could result in damage to the adjacent forward edge frame of
the door and consequent loss of a MED and rapid decompression of the
airplane.

Compliance

(e) You are responsible for having the actions required by this
AD performed within the compliance times specified, unless the
actions have already been done.

Requirements of AD 98-26-13

Inspections and Corrective Action

(f) For Model 747-100, -100B, -100B SUD, -200, -200B, -200C, -
300, -400, and 747SR series airplanes having line numbers 1 through
830 inclusive: Within 18 months after January 25, 1999 (the
effective date of AD 98-26-13, amendment 39-10954), perform a high
frequency eddy current (HFEC) inspection to determine the material
type of the stop support fittings of the MEDs, in accordance with
the Accomplishment Instructions of Boeing Service Bulletin 747-53-
2358, dated August 26, 1993; or Boeing Service Bulletin 747-53-2358,
Revision 1, dated April 19, 2001. Perform the inspection only at
those locations where the material type of the stop support fittings
is unknown, as specified in Figure 3, Table 1, of either service
bulletin. As of the effective date of this AD, do the actions in
accordance with Boeing Service Bulletin 747-53-2358, Revision 1,
dated April 19, 2001.
(1) If the fitting is made from 7075-T73 or 7050-T7451 material,
no further action is required by this AD for that fitting; however,
the requirements of paragraph (l) of this AD still apply.
(2) If the fitting is not made from 7075-T73 or 7050-T7451
material, before further flight, perform a detailed inspection to
detect cracks of the stop support fitting of the MEDs, in accordance
with the applicable service bulletin.

Note 1: For the purposes of this AD, a detailed inspection is
``an intensive examination of a specific item, installation, or
assembly to detect damage, failure, or irregularity. Available
lighting is normally supplemented with a direct source of good
lighting at an intensity deemed appropriate. Inspection aids such as
mirrors magnifying lenses, etc. may be necessary. Surface cleaning
and elaborate procedures may be required.''

(i) If no crack is detected, repeat the detailed inspection
thereafter at intervals not to exceed 36 months or 2,000 flight
cycles, whichever occurs first.
(ii) If any crack is detected, before further flight, replace
the fitting with a stop support fitting made from 7075-T73 or 7050-
T7451 material, in accordance with the applicable service bulletin.
(g) For Model 747-100, -100B, -100B SUD, -200, -200B, -200C, -
300, -400, and 747SR series airplanes having line numbers 1 through
830 inclusive: Replacement of the stop support fitting of the MEDs
with a stop support fitting made from 7075-T73 material, in
accordance with Boeing Service Bulletin 747-53-2358, dated August
26, 1993; or replacement with a stop support fitting made from 7075-
T73 or 7050-T7451 material, in accordance with Boeing Service
Bulletin 747-53-2358, Revision 1, dated April 19, 2001; constitutes
terminating action for the repetitive inspection requirements of
paragraph (f) of this AD for the replaced fitting. As of the
effective date of this AD, only Boeing Service Bulletin 747-53-2358,
Revision 1, dated April 19, 2001, may be used.

New Requirements of This AD

Note 2: Operators are not required to remove foam and inspect/
drill drain holes as specified in Paragraph 3.B.1.e. and the Notes
of the Accomplishment Instructions of Boeing Special Attention
Service Bulletin 747-53-2485, dated January 8, 2004, when doing any
inspection required by paragraphs (h), (i), and (k) of this AD.

Inspection for Material Type

(h) For Model 747-100, -100B, -100B SUD, -200B, -200C, -300, -
400, and -400D series airplanes, and Model 747SR series airplanes,
having line numbers 1 through 830 inclusive on which the actions
specified in the Accomplishment Instructions of Boeing Service
Bulletin 747-53-2358, dated August 26, 1993; or Boeing Service
Bulletin 747-53-2358, Revision 1, dated April 19, 2001; have been
done: Do the inspection specified in paragraph (h)(1) or (h)(2) of
this AD, as applicable, at the time specified.
(1) Except as provided by paragraph (h)(2) of this AD, if any
stop support fitting, 2L through 6L and 2R through 6R, of MED 3, was
replaced before the effective date of this AD: Perform a one-time
HFEC inspection to determine the material type of the stop support
fittings of MED 3 that were replaced, in accordance with the
Accomplishment Instructions of Boeing Special Attention

[[Page 28803]]

Service Bulletin 747-53-2485, dated January 8, 2004, at the later of
the times specified in paragraphs (h)(1)(i) and (h)(1)(ii) of this
AD.
(i) Within 72 months after the stop support fitting of MED 3 was
replaced.
(ii) Within 18 months after the effective date of this AD.
(2) If any stop support fitting, 2L through 6L and 2R through
6R, of MED 3, cannot be determined conclusively by reviewing
airplane maintenance records that the fitting was not replaced,
within 18 months after the effective date of this AD, perform a one-
time HFEC inspection to determine the material type of the stop
support fitting, in accordance with the Accomplishment Instructions
of Boeing Special Attention Service Bulletin 747-53-2485, dated
January 8, 2004.
(i) For airplanes having line numbers 831 through 1301
inclusive: At the later of the times specified in paragraphs (i)(1)
and (i)(2) of this AD, perform a one-time HFEC inspection to
determine the material type of the stop support fittings of MED 3 in
accordance with the Accomplishment Instructions of Boeing Special
Attention Service Bulletin 747-53-2485, dated January 8, 2004.
(1) Before 72 months since the date of issuance of the original
Airworthiness Certificate or the date of issuance of the original
Export Certificate of Airworthiness.
(2) Within 18 months after the effective date of this AD.

No Further Action

(j) If, during any HFEC inspection required by paragraph (h) or
(i) of this AD, any fitting is found to be made of 7075-T73 or 7050-
T7451 material, no further action is required by this AD for that
fitting; however, paragraph (l) of this AD still applies.

Initial and Repetitive Inspections for Cracking and Corrective Action

(k) If, during any HFEC inspection required by paragraph (h) or
(i) of this AD, any fitting is found not to be made of 7075-T73 or
7050-T7451 material, before further flight, perform a detailed
inspection for cracks of the fitting in accordance with the
Accomplishment Instructions of Boeing Special Attention Service
Bulletin 747-53-2485, dated January 8, 2004.
(1) If no crack is detected, repeat the detailed inspection
specified in paragraph (k) of this AD thereafter at intervals not to
exceed 36 months or 2,000 flight cycles, whichever comes first.
Doing the replacement specified in paragraph (k)(2) of this AD ends
the repetitive inspections for the replaced fitting.
(2) If any crack is detected, before further flight, replace the
fitting with a fitting made of 7075-T73 or 7050-T7451 material in
accordance with the Accomplishment Instructions of Boeing Special
Attention Service Bulletin 747-53-2485, dated January 8, 2004. No
further action is required by this AD for that fitting; however,
paragraph (l) of this AD still applies.

Parts Installation

(l) As of the date specified in paragraph (l)(1) or (l)(2) of
this AD, as applicable, no person shall install on any airplane a
stop support fitting of the MEDs made from either 7079-T651 or 7075-
T651 material.
(1) For airplanes having line numbers 1 through 830 inclusive:
As of January 25, 1999.
(2) For airplanes having line numbers 831 through 1301
inclusive: As of the effective date of this AD.

Alternative Methods of Compliance (AMOCs)

(m)(1) The Manager, Seattle Aircraft Certification Office (ACO),
FAA, has the authority to approve AMOCs for this AD, if requested
using the procedures found in 14 CFR 39.19.
(2) AMOCs, approved previously per AD 98-26-13, amendment 39-
10954, are approved as AMOCs with paragraph (f) or (g) of this AD,
as applicable. However, any stop support fitting, 2L through 6L and
2R through 6R, of MED 3 that was replaced is still required to be
inspected as required in paragraph (h) of this AD.

Material Incorporated by Reference

(n) You must use the service information that is specified in
Table 1 of this AD to perform the actions that are required by this
AD, unless the AD specifies otherwise.
(1) The Director of the Federal Register approves the
incorporation by reference of Boeing Service Bulletin 747-53-2358,
Revision 1, dated April 19, 2001; and Boeing Special Attention
Service Bulletin 747-53-2485, dated January 8, 2004; in accordance
with 5 U.S.C. 552(a) and 1 CFR part 51.
(2) The Director of the Federal Register previously approved the
incorporation by reference of Boeing Service Bulletin 747-53-2358,
dated August 26, 1993, as of January 25, 1999 (63 FR 70316, December
21, 1998).
(3) To get copies of the service information, go to Boeing
Commercial Airplanes, P.O. Box 3707, Seattle, Washington 98124-2207.
To view the AD docket, go to the Docket Management Facility, U.S.
Department of Transportation, 400 Seventh Street SW., room PL-401,
Nassif Building, Washington, DC. To review copies of the service
information, go to the National Archives and Records Administration
(NARA). For information on the availability of this material at the
NARA, call (202) 741-6030, or go to https://www.archives.gov/
federal_register/code_of_federal_regulations/ibr_
locations.html.

Table 1.--Material Incorporated by Reference
----------------------------------------------------------------------------------------------------------------
Service bulletin Revision level Date
----------------------------------------------------------------------------------------------------------------
Boeing Service Bulletin 747-53-2358............ Original.................... August 26, 1993.
Boeing Service Bulletin 747-53-2358............ 1........................... April 19, 2001.
Boeing Special Attention Service Bulletin 747- Original.................... January 8, 2004.
53-2485.
----------------------------------------------------------------------------------------------------------------

Issued in Renton, Washington, on May 9, 2005.
Jeffrey E. Duven,
Acting Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. 05-9876 Filed 5-18-05; 8:45 am]
BILLING CODE 4910-13-P

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.