Airworthiness Directives; Boeing Model 767 Airplanes Equipped with General Electric Model CF6-80C2 Engines, 28489-28491 [05-9872]
Download as PDF
Federal Register / Vol. 70, No. 95 / Wednesday, May 18, 2005 / Proposed Rules
Chatham
Davidson
Davie
Edgecombe
Franklin
Forsyth
Granville
Guilford
Halifax
Lee
Montgomery
Moore
Nash
Northampton
Person
Randolph
Richmond
Robeson
Rockingham
Sampson
Scotland
Stokes
Surry
Vance
Warren
Wilson
Yadkin
South Carolina:
Dillon
Marion
Marlboro
*
*
*
between the upper actuator and the
TRAS lock. We are proposing this AD to
prevent high power in-flight
deployment of a thrust reverser, which
could cause high roll force and
consequent departure from controlled
flight.
*
*
[FR Doc. 05–9894 Filed 5–17–05; 8:45 am]
BILLING CODE 6325–39–P
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA–2005–21236; Directorate
Identifier 2005–NM–011–AD]
RIN 2120–AA64
Airworthiness Directives; Boeing
Model 767 Airplanes Equipped with
General Electric Model CF6–80C2
Engines
Federal Aviation
Administration (FAA), Department of
Transportation (DOT).
ACTION: Notice of proposed rulemaking
(NPRM).
AGENCY:
SUMMARY: The FAA proposes to adopt a
new airworthiness directive (AD) for
certain Boeing Model 767 airplanes.
This proposed AD would require
modifying a relay installation and
associated wiring of the engine cowl
anti-ice system and performing a
functional test of the thrust reverser
system. This proposed AD would also
require replacing the operational
program software of certain indicating/
recording systems. This proposed AD is
prompted by numerous operator reports
of failures of the lock flexshaft of the
thrust reverser actuation system (TRAS)
VerDate jul<14>2003
We must receive comments on
this proposed AD by July 5, 2005.
ADDRESSES: Use one of the following
addresses to submit comments on this
proposed AD.
• DOT Docket Web site: Go to
https://dms.dot.gov and follow the
instructions for sending your comments
electronically.
• Government-wide rulemaking Web
site: Go to https://www.regulations.gov
and follow the instructions for sending
your comments electronically.
• Mail: Docket Management Facility,
U.S. Department of Transportation, 400
Seventh Street, SW., Nassif Building,
room PL–401, Washington, DC 20590.
• By fax: (202) 493–2251.
• Hand Delivery: Room PL–401 on
the plaza level of the Nassif Building,
400 Seventh Street, SW., Washington,
DC, between 9 a.m. and 5 p.m., Monday
through Friday, except Federal holidays.
For service information identified in
this proposed AD, contact Boeing
Commercial Airplanes, P.O. Box 3707,
Seattle, Washington 98124–2207.
You can examine the contents of this
AD docket on the Internet at https://
dms.dot.gov, or in person at the Docket
Management Facility, U.S. Department
of Transportation, 400 Seventh Street,
SW., room PL–401, on the plaza level of
the Nassif Building, Washington, DC.
This docket number is FAA–2005–
21236; the directorate identifier for this
docket is 2005–NM–011–AD.
FOR FURTHER INFORMATION CONTACT:
Sulmo Mariano, Aerospace Engineer,
Propulsion Branch, ANM–140S, FAA,
Seattle Aircraft Certification Office,
1601 Lind Avenue, SW., Renton,
Washington 98055–4056; telephone
(425) 917–6501; fax (425) 917–6590.
SUPPLEMENTARY INFORMATION:
DATES:
18:53 May 17, 2005
Jkt 205001
Comments Invited
We invite you to submit any relevant
written data, views, or arguments
regarding this proposed AD. Send your
comments to an address listed under
ADDRESSES. Include ‘‘Docket No. FAA–
2005–21236; Directorate Identifier
2005–NM–011–AD’’ in the subject line
of your comments. We specifically
invite comments on the overall
regulatory, economic, environmental,
and energy aspects of the proposed AD.
We will consider all comments
submitted by the closing date and may
PO 00000
Frm 00002
Fmt 4702
Sfmt 4702
28489
amend the proposed AD in light of those
comments.
We will post all comments we
receive, without change, to https://
dms.dot.gov, including any personal
information you provide. We will also
post a report summarizing each
substantive verbal contact with FAA
personnel concerning this proposed AD.
Using the search function of that Web
site, anyone can find and read the
comments in any of our dockets,
including the name of the individual
who sent the comment (or signed the
comment on behalf of an association,
business, labor union, etc.). You can
review DOT’s complete Privacy Act
Statement in the Federal Register
published on April 11, 2000 (65 FR
19477–78), or you can visit https://
dms.dot.gov.
Examining the Docket
You can examine the AD docket on
the Internet at https://dms.dot.gov, or in
person at the Docket Management
Facility office between 9 a.m. and 5
p.m., Monday through Friday, except
Federal holidays. The Docket
Management Facility office (telephone
(800) 647–5227) is located on the plaza
level of the Nassif Building at the DOT
street address stated in the ADDRESSES
section. Comments will be available in
the AD docket shortly after the DMS
receives them.
Discussion
We have received a report that
operators have reported more than 140
failures of the lock flexshaft of the thrust
reverser actuation system (TRAS)
between the upper actuator and the
TRAS lock, on certain Boeing Model
767 airplanes. Analysis showed these
failures were caused by pneumatic
pressure that was insufficient to
decelerate the TRAS at the end of the
deploy stroke. This condition, if not
corrected, could result in high power inflight deployment of a thrust reverser,
which could cause high roll force and
consequent departure from controlled
flight.
Related Rulemaking
On April 26, 2000, we issued AD
2000–09–04, amendment 39–11712 (65
FR 25833, May 4, 2000), which is
applicable to certain Boeing Model 767
series airplanes equipped with General
Electric Model CF6–80C2 engines. That
AD requires tests, inspections, and
adjustments of the thrust reverser
system and installation of a terminating
modification and repetitive follow-on
actions; in accordance with Boeing
Service Bulletin 767–78A0081, Revision
1, dated October 9, 1997; Boeing Service
E:\FR\FM\18MYP1.SGM
18MYP1
28490
Federal Register / Vol. 70, No. 95 / Wednesday, May 18, 2005 / Proposed Rules
Bulletin 767–78–0063, Revision 2, dated
April 28, 1994; and Boeing Service
Bulletin 767–78–0047, Revision 3, dated
July 28, 1994.
On July 27, 2001, we issued AD 2001–
16–03, amendment 39–12371 (66 FR
40880, August 6, 2001), which is
applicable to certain Boeing Model 767–
200, –300, –300F, and –400ER series
airplanes equipped with General
Electric Model CF6–80C2 engines. That
AD requires various repetitive
inspections and tests of certain fail-safe
features of the thrust reverser control
system and corrective actions if
necessary; in accordance with Boeing
Service Bulletin 767–78A0090, Revision
1, dated July 5, 2001, and Boeing Alert
Service Bulletin 767–78A0091, Revision
1, dated July 5, 2001.
Relevant Service Information
We have reviewed Boeing Service
Bulletin 767–78A0092, Revision 1,
dated October 30, 2003 (for Model 767–
200, –300, and –300F airplanes); and
Boeing Alert Service Bulletin 767–
78A0093, dated May 6, 2004 (for Model
767–400ER airplanes). The service
bulletins describe procedures for
modifying a relay installation and
associated wiring of the engine cowl
anti-ice system and for performing a
functional test of the thrust reverser
system.
Service Bulletin 767–78A0092
specifies prior or concurrent
accomplishment of Boeing Service
Bulletin 767–31–0180, dated December
5, 2002 (for Model 767–200, –300, and
–300F airplanes). Service Bulletin 767–
31–0180 describes procedures for
replacing the operational program
software (OPS) in the left and right
engine indication and crew alerting
system (EICAS) computers. The
software update incorporates design
improvements and EICAS message logic
revisions.
Alert Service Bulletin 767–78A0093
specifies prior or concurrent
accomplishment of Boeing Service
Bulletin 767–31–0176, dated February
26, 2004 (for Model 767–400ER
airplanes). Service Bulletin 767–31A–
0176 describes procedures for replacing
the OPS of the large format display
system (LFDS). The software update
incorporates problem fixes,
functionality improvements, and FAA
required changes.
Accomplishing the actions specified
in the service information is intended to
adequately address the unsafe
condition.
FAA’s Determination and Requirements
of the Proposed AD
We have evaluated all pertinent
information and identified an unsafe
condition that is likely to exist or
develop on other airplanes of this same
type design. Therefore, we are
proposing this AD, which would require
accomplishing the actions specified in
the service information described
previously, except as discussed under
‘‘Difference Between the Proposed AD
and Service Information.’’
Difference Between the Proposed AD
and Service Information
The effectivities stated in the service
bulletins are different.
• Service Bulletin 767–78A0092
states ‘‘all CF6–80C2 powered 767–200,
–300, and –300F airplanes line numbers
0001–0882’’ while concurrent Service
Bulletin 767–31–0180 states ‘‘all 767–
200, -300, and -300F airplanes line
numbers 1–881.’’
• Alert Service Bulletin 767–78A0093
states ‘‘all CF6–80C2 powered 767–
400ER airplanes line numbers 0001–
0882’’ while concurrent Service Bulletin
767–31–0176 states ‘‘767–400ER before
Line Number 930.’’
We have therefore analyzed the
service bulletins and determined that
the effectivity of this proposed AD
should read ‘‘Boeing Model 767–200,
–300, –300F, and –400ER series
airplanes; certificated in any category;
having line numbers 0001 through 0882
inclusive; equipped with General
Electric Model CF6–80C2 engines’’ to
ensure that all airplanes subject to the
unsafe condition will be identified. The
various actions in this proposed AD
reflect the individual groups of
airplanes within the applicability that
are subject to the proposed
requirements. This difference has been
coordinated with Boeing.
Costs of Compliance
There are about 400 airplanes of the
affected design in the worldwide fleet.
This proposed AD would affect about
142 airplanes of U.S. registry. The
following table provides the estimated
costs for U.S. operators to comply with
this proposed AD, at an average labor
rate of $65 per work hour.
ESTIMATED COSTS
Action
Work hours
Parts
Cost per airplane
For Model 767–200, –300, and –300F Series Airplanes
Modify relay and wiring ........................................................................................................
Functional test .....................................................................................................................
Install EICAS OPS software ................................................................................................
5
3
2
$1,307–$1,390
N/A
N/A
$1,632–$1,715
195
130
5
3
3
2,119
N/A
N/A
2,444
195
195
For Model 767–400ER Series Airplanes
Modify relay and wiring ........................................................................................................
Functional test .....................................................................................................................
Install LFDS OPS software ..................................................................................................
Authority for This Rulemaking
Title 49 of the United States Code
specifies the FAA’s authority to issue
rules on aviation safety. Subtitle I,
Section 106, describes the authority of
the FAA Administrator. Subtitle VII,
Aviation Programs, describes in more
detail the scope of the Agency’s
authority.
VerDate jul<14>2003
18:53 May 17, 2005
Jkt 205001
We are issuing this rulemaking under
the authority described in Subtitle VII,
Part A, Subpart III, Section 44701,
‘‘General requirements.’’ Under that
section, Congress charges the FAA with
promoting safe flight of civil aircraft in
air commerce by prescribing regulations
for practices, methods, and procedures
the Administrator finds necessary for
safety in air commerce. This regulation
PO 00000
Frm 00003
Fmt 4702
Sfmt 4702
is within the scope of that authority
because it addresses an unsafe condition
that is likely to exist or develop on
products identified in this rulemaking
action.
Regulatory Findings
We have determined that this
proposed AD would not have federalism
implications under Executive Order
E:\FR\FM\18MYP1.SGM
18MYP1
Federal Register / Vol. 70, No. 95 / Wednesday, May 18, 2005 / Proposed Rules
13132. This proposed AD would not
have a substantial direct effect on the
States, on the relationship between the
national Government and the States, or
on the distribution of power and
responsibilities among the various
levels of government.
For the reasons discussed above, I
certify that the proposed regulation:
1. Is not a ‘‘significant regulatory
action’’ under Executive Order 12866;
2. Is not a ‘‘significant rule’’ under the
DOT Regulatory Policies and Procedures
(44 FR 11034, February 26, 1979); and
3. Will not have a significant
economic impact, positive or negative,
on a substantial number of small entities
under the criteria of the Regulatory
Flexibility Act.
We prepared a regulatory evaluation
of the estimated costs to comply with
this proposed AD. See the ADDRESSES
section for a location to examine the
regulatory evaluation.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation
safety, Safety.
The Proposed Amendment
Accordingly, under the authority
delegated to me by the Administrator,
the FAA proposes to amend 14 CFR part
39 as follows:
PART 39—AIRWORTHINESS
DIRECTIVES
1. The authority citation for part 39
continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
§ 39.13
[Amended]
2. The FAA amends § 39.13 by adding
the following new airworthiness
directive (AD):
Boeing: Docket No. FAA–2005–21236;
Directorate Identifier 2005–NM–011–AD.
Comments Due Date
(a) The Federal Aviation Administration
(FAA) must receive comments on this AD
action by July 5, 2005.
Affected ADs
(b) None.
Applicability
(c) This AD applies to Boeing Model 767–
200, –300, –300F, and –400ER series
airplanes; certificated in any category; having
line numbers 0001 through 0882 inclusive;
equipped with General Electric Model CF6–
80C2 engines.
of a thrust reverser, which could cause high
roll force and consequent departure from
controlled flight.
Compliance
(e) You are responsible for having the
actions required by this AD performed within
the compliance times specified, unless the
actions have already been done.
Modification and Functional Test
(f) Within 48 months after the effective
date of this AD, perform the actions required
by paragraphs (f)(1) and (f)(2) of this AD in
accordance with the Accomplishment
Instructions of Boeing Service Bulletin 767–
78A0092, Revision 1, dated October 30, 2003
(for Model 767–200, –300, and –300F series
airplanes); or Boeing Alert Service Bulletin
767–78A0093, dated May 6, 2004 (for Model
767–400ER series airplanes); as applicable.
(1) Modify the relay installation and
associated wiring of the engine cowl anti-ice
system.
(2) Perform a functional test of the thrust
reverser system.
Concurrent Service Bulletins
(g) Prior to or concurrently with the actions
required by paragraphs (f)(1) and (f)(2) of this
AD, perform the actions required by
paragraphs (g)(1) and (g)(2) of this AD in
accordance with the Accomplishment
Instructions of the applicable service
bulletin.
(1) For Model 767–200, –300, and –300F
series airplanes: Replace the operational
program software (OPS) in the left and right
engine indication and crew alerting system
(EICAS) computers as specified in Boeing
Service Bulletin 767–31–0180, dated
December 5, 2002.
(2) For Model 767–400ER airplanes:
Replace the OPS of the large format display
system (LFDS) as specified in Boeing Service
Bulletin 767–31–0176, dated February 26,
2004.
Alternative Methods of Compliance
(AMOCs)
(h) The Manager, Seattle Aircraft
Certification Office (ACO), FAA, has the
authority to approve AMOCs for this AD, if
requested in accordance with the procedures
found in 14 CFR 39.19.
Issued in Renton, Washington, on May 9,
2005.
Jeffrey E. Duven,
Acting Manager, Transport Airplane
Directorate, Aircraft Certification Service.
[FR Doc. 05–9872 Filed 5–17–05; 8:45 am]
BILLING CODE 4910–13–P
Unsafe Condition
(d) This AD was prompted by numerous
operator reports of failures of the lock
flexshaft of the thrust reverser actuation
system (TRAS) between the upper actuator
and the TRAS lock. We are issuing this AD
to prevent high power in-flight deployment
VerDate jul<14>2003
18:53 May 17, 2005
Jkt 205001
PO 00000
Frm 00004
Fmt 4702
Sfmt 4702
28491
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA–2004–19534; Directorate
Identifier 2004–NM–99–AD]
RIN 2120–AA64
Airworthiness Directives; Airbus Model
A300 B2 and B4 Series Airplanes;
Model A300 B4–600, B4–600R, and F4–
600R Series Airplanes, and Model C4–
605R Variant F Airplanes (Collectively
Called A300–600); and Model A310
Series Airplanes
Federal Aviation
Administration (FAA), DOT.
ACTION: Supplemental notice of
proposed rulemaking (NPRM);
reopening of comment period.
AGENCY:
SUMMARY: The FAA is revising an earlier
NPRM for an airworthiness directive
(AD) that applies to certain Airbus
airplane models, as specified above. The
original NPRM would have required
modifying the thermal insulation system
of certain fuselage frames, and
modifying the fuselage drainage system.
The original NPRM would also have
required revising the FAA-approved
maintenance inspection program to
include inspections for corrosion or
cracking in the subject areas. The
original NPRM was prompted by reports
of corrosion in the lower part of the
pressure bulkhead at certain fuselage
frames. This action revises the original
NPRM by expanding the applicability to
include additional airplanes. We are
proposing this supplemental NPRM to
prevent accumulation of condensation
in the insulation blankets of certain
fuselage frames, which could cause
corrosion that could result in reduced
structural integrity of the fuselage and
consequent rapid decompression of the
airplane.
DATES: We must receive comments on
this supplemental NPRM by June 13,
2005.
Use one of the following
addresses to submit comments on this
supplemental NPRM.
• DOT Docket Web site: Go to
https://dms.dot.gov and follow the
instructions for sending your comments
electronically.
• Government-wide rulemaking Web
site: Go to https://www.regulations.gov
and follow the instructions for sending
your comments electronically.
• Mail: Docket Management Facility;
U.S. Department of Transportation, 400
Seventh Street, SW., Nassif Building,
room PL–401, Washington, DC 20590.
ADDRESSES:
E:\FR\FM\18MYP1.SGM
18MYP1
Agencies
[Federal Register Volume 70, Number 95 (Wednesday, May 18, 2005)]
[Proposed Rules]
[Pages 28489-28491]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 05-9872]
=======================================================================
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2005-21236; Directorate Identifier 2005-NM-011-AD]
RIN 2120-AA64
Airworthiness Directives; Boeing Model 767 Airplanes Equipped
with General Electric Model CF6-80C2 Engines
AGENCY: Federal Aviation Administration (FAA), Department of
Transportation (DOT).
ACTION: Notice of proposed rulemaking (NPRM).
-----------------------------------------------------------------------
SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD)
for certain Boeing Model 767 airplanes. This proposed AD would require
modifying a relay installation and associated wiring of the engine cowl
anti-ice system and performing a functional test of the thrust reverser
system. This proposed AD would also require replacing the operational
program software of certain indicating/recording systems. This proposed
AD is prompted by numerous operator reports of failures of the lock
flexshaft of the thrust reverser actuation system (TRAS) between the
upper actuator and the TRAS lock. We are proposing this AD to prevent
high power in-flight deployment of a thrust reverser, which could cause
high roll force and consequent departure from controlled flight.
DATES: We must receive comments on this proposed AD by July 5, 2005.
ADDRESSES: Use one of the following addresses to submit comments on
this proposed AD.
DOT Docket Web site: Go to https://dms.dot.gov and follow
the instructions for sending your comments electronically.
Government-wide rulemaking Web site: Go to https://
www.regulations.gov and follow the instructions for sending your
comments electronically.
Mail: Docket Management Facility, U.S. Department of
Transportation, 400 Seventh Street, SW., Nassif Building, room PL-401,
Washington, DC 20590.
By fax: (202) 493-2251.
Hand Delivery: Room PL-401 on the plaza level of the
Nassif Building, 400 Seventh Street, SW., Washington, DC, between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
For service information identified in this proposed AD, contact
Boeing Commercial Airplanes, P.O. Box 3707, Seattle, Washington 98124-
2207.
You can examine the contents of this AD docket on the Internet at
https://dms.dot.gov, or in person at the Docket Management Facility,
U.S. Department of Transportation, 400 Seventh Street, SW., room PL-
401, on the plaza level of the Nassif Building, Washington, DC. This
docket number is FAA-2005-21236; the directorate identifier for this
docket is 2005-NM-011-AD.
FOR FURTHER INFORMATION CONTACT: Sulmo Mariano, Aerospace Engineer,
Propulsion Branch, ANM-140S, FAA, Seattle Aircraft Certification
Office, 1601 Lind Avenue, SW., Renton, Washington 98055-4056; telephone
(425) 917-6501; fax (425) 917-6590.
SUPPLEMENTARY INFORMATION:
Comments Invited
We invite you to submit any relevant written data, views, or
arguments regarding this proposed AD. Send your comments to an address
listed under ADDRESSES. Include ``Docket No. FAA-2005-21236;
Directorate Identifier 2005-NM-011-AD'' in the subject line of your
comments. We specifically invite comments on the overall regulatory,
economic, environmental, and energy aspects of the proposed AD. We will
consider all comments submitted by the closing date and may amend the
proposed AD in light of those comments.
We will post all comments we receive, without change, to https://
dms.dot.gov, including any personal information you provide. We will
also post a report summarizing each substantive verbal contact with FAA
personnel concerning this proposed AD. Using the search function of
that Web site, anyone can find and read the comments in any of our
dockets, including the name of the individual who sent the comment (or
signed the comment on behalf of an association, business, labor union,
etc.). You can review DOT's complete Privacy Act Statement in the
Federal Register published on April 11, 2000 (65 FR 19477-78), or you
can visit https://dms.dot.gov.
Examining the Docket
You can examine the AD docket on the Internet at https://
dms.dot.gov, or in person at the Docket Management Facility office
between 9 a.m. and 5 p.m., Monday through Friday, except Federal
holidays. The Docket Management Facility office (telephone (800) 647-
5227) is located on the plaza level of the Nassif Building at the DOT
street address stated in the ADDRESSES section. Comments will be
available in the AD docket shortly after the DMS receives them.
Discussion
We have received a report that operators have reported more than
140 failures of the lock flexshaft of the thrust reverser actuation
system (TRAS) between the upper actuator and the TRAS lock, on certain
Boeing Model 767 airplanes. Analysis showed these failures were caused
by pneumatic pressure that was insufficient to decelerate the TRAS at
the end of the deploy stroke. This condition, if not corrected, could
result in high power in-flight deployment of a thrust reverser, which
could cause high roll force and consequent departure from controlled
flight.
Related Rulemaking
On April 26, 2000, we issued AD 2000-09-04, amendment 39-11712 (65
FR 25833, May 4, 2000), which is applicable to certain Boeing Model 767
series airplanes equipped with General Electric Model CF6-80C2 engines.
That AD requires tests, inspections, and adjustments of the thrust
reverser system and installation of a terminating modification and
repetitive follow-on actions; in accordance with Boeing Service
Bulletin 767-78A0081, Revision 1, dated October 9, 1997; Boeing Service
[[Page 28490]]
Bulletin 767-78-0063, Revision 2, dated April 28, 1994; and Boeing
Service Bulletin 767-78-0047, Revision 3, dated July 28, 1994.
On July 27, 2001, we issued AD 2001-16-03, amendment 39-12371 (66
FR 40880, August 6, 2001), which is applicable to certain Boeing Model
767-200, -300, -300F, and -400ER series airplanes equipped with General
Electric Model CF6-80C2 engines. That AD requires various repetitive
inspections and tests of certain fail-safe features of the thrust
reverser control system and corrective actions if necessary; in
accordance with Boeing Service Bulletin 767-78A0090, Revision 1, dated
July 5, 2001, and Boeing Alert Service Bulletin 767-78A0091, Revision
1, dated July 5, 2001.
Relevant Service Information
We have reviewed Boeing Service Bulletin 767-78A0092, Revision 1,
dated October 30, 2003 (for Model 767-200, -300, and -300F airplanes);
and Boeing Alert Service Bulletin 767-78A0093, dated May 6, 2004 (for
Model 767-400ER airplanes). The service bulletins describe procedures
for modifying a relay installation and associated wiring of the engine
cowl anti-ice system and for performing a functional test of the thrust
reverser system.
Service Bulletin 767-78A0092 specifies prior or concurrent
accomplishment of Boeing Service Bulletin 767-31-0180, dated December
5, 2002 (for Model 767-200, -300, and -300F airplanes). Service
Bulletin 767-31-0180 describes procedures for replacing the operational
program software (OPS) in the left and right engine indication and crew
alerting system (EICAS) computers. The software update incorporates
design improvements and EICAS message logic revisions.
Alert Service Bulletin 767-78A0093 specifies prior or concurrent
accomplishment of Boeing Service Bulletin 767-31-0176, dated February
26, 2004 (for Model 767-400ER airplanes). Service Bulletin 767-31A-0176
describes procedures for replacing the OPS of the large format display
system (LFDS). The software update incorporates problem fixes,
functionality improvements, and FAA required changes.
Accomplishing the actions specified in the service information is
intended to adequately address the unsafe condition.
FAA's Determination and Requirements of the Proposed AD
We have evaluated all pertinent information and identified an
unsafe condition that is likely to exist or develop on other airplanes
of this same type design. Therefore, we are proposing this AD, which
would require accomplishing the actions specified in the service
information described previously, except as discussed under
``Difference Between the Proposed AD and Service Information.''
Difference Between the Proposed AD and Service Information
The effectivities stated in the service bulletins are different.
Service Bulletin 767-78A0092 states ``all CF6-80C2 powered
767-200, -300, and -300F airplanes line numbers 0001-0882'' while
concurrent Service Bulletin 767-31-0180 states ``all 767-200, -300, and
-300F airplanes line numbers 1-881.''
Alert Service Bulletin 767-78A0093 states ``all CF6-80C2
powered 767-400ER airplanes line numbers 0001-0882'' while concurrent
Service Bulletin 767-31-0176 states ``767-400ER before Line Number
930.''
We have therefore analyzed the service bulletins and determined
that the effectivity of this proposed AD should read ``Boeing Model
767-200, -300, -300F, and -400ER series airplanes; certificated in any
category; having line numbers 0001 through 0882 inclusive; equipped
with General Electric Model CF6-80C2 engines'' to ensure that all
airplanes subject to the unsafe condition will be identified. The
various actions in this proposed AD reflect the individual groups of
airplanes within the applicability that are subject to the proposed
requirements. This difference has been coordinated with Boeing.
Costs of Compliance
There are about 400 airplanes of the affected design in the
worldwide fleet. This proposed AD would affect about 142 airplanes of
U.S. registry. The following table provides the estimated costs for
U.S. operators to comply with this proposed AD, at an average labor
rate of $65 per work hour.
Estimated Costs
----------------------------------------------------------------------------------------------------------------
Action Work hours Parts Cost per airplane
----------------------------------------------------------------------------------------------------------------
For Model 767-200, -300, and -300F Series Airplanes
----------------------------------------------------------------------------------------------------------------
Modify relay and wiring...................................... 5 $1,307-$1,390 $1,632-$1,715
Functional test.............................................. 3 N/A 195
Install EICAS OPS software................................... 2 N/A 130
--------------------------------------------------------------
For Model 767-400ER Series Airplanes
----------------------------------------------------------------------------------------------------------------
Modify relay and wiring...................................... 5 2,119 2,444
Functional test.............................................. 3 N/A 195
Install LFDS OPS software.................................... 3 N/A 195
----------------------------------------------------------------------------------------------------------------
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, Section 106, describes the
authority of the FAA Administrator. Subtitle VII, Aviation Programs,
describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701, ``General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
We have determined that this proposed AD would not have federalism
implications under Executive Order
[[Page 28491]]
13132. This proposed AD would not have a substantial direct effect on
the States, on the relationship between the national Government and the
States, or on the distribution of power and responsibilities among the
various levels of government.
For the reasons discussed above, I certify that the proposed
regulation:
1. Is not a ``significant regulatory action'' under Executive Order
12866;
2. Is not a ``significant rule'' under the DOT Regulatory Policies
and Procedures (44 FR 11034, February 26, 1979); and
3. Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to
comply with this proposed AD. See the ADDRESSES section for a location
to examine the regulatory evaluation.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Safety.
The Proposed Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
2. The FAA amends Sec. 39.13 by adding the following new
airworthiness directive (AD):
Boeing: Docket No. FAA-2005-21236; Directorate Identifier 2005-NM-
011-AD.
Comments Due Date
(a) The Federal Aviation Administration (FAA) must receive
comments on this AD action by July 5, 2005.
Affected ADs
(b) None.
Applicability
(c) This AD applies to Boeing Model 767-200, -300, -300F, and -
400ER series airplanes; certificated in any category; having line
numbers 0001 through 0882 inclusive; equipped with General Electric
Model CF6-80C2 engines.
Unsafe Condition
(d) This AD was prompted by numerous operator reports of
failures of the lock flexshaft of the thrust reverser actuation
system (TRAS) between the upper actuator and the TRAS lock. We are
issuing this AD to prevent high power in-flight deployment of a
thrust reverser, which could cause high roll force and consequent
departure from controlled flight.
Compliance
(e) You are responsible for having the actions required by this
AD performed within the compliance times specified, unless the
actions have already been done.
Modification and Functional Test
(f) Within 48 months after the effective date of this AD,
perform the actions required by paragraphs (f)(1) and (f)(2) of this
AD in accordance with the Accomplishment Instructions of Boeing
Service Bulletin 767-78A0092, Revision 1, dated October 30, 2003
(for Model 767-200, -300, and -300F series airplanes); or Boeing
Alert Service Bulletin 767-78A0093, dated May 6, 2004 (for Model
767-400ER series airplanes); as applicable.
(1) Modify the relay installation and associated wiring of the
engine cowl anti-ice system.
(2) Perform a functional test of the thrust reverser system.
Concurrent Service Bulletins
(g) Prior to or concurrently with the actions required by
paragraphs (f)(1) and (f)(2) of this AD, perform the actions
required by paragraphs (g)(1) and (g)(2) of this AD in accordance
with the Accomplishment Instructions of the applicable service
bulletin.
(1) For Model 767-200, -300, and -300F series airplanes: Replace
the operational program software (OPS) in the left and right engine
indication and crew alerting system (EICAS) computers as specified
in Boeing Service Bulletin 767-31-0180, dated December 5, 2002.
(2) For Model 767-400ER airplanes: Replace the OPS of the large
format display system (LFDS) as specified in Boeing Service Bulletin
767-31-0176, dated February 26, 2004.
Alternative Methods of Compliance (AMOCs)
(h) The Manager, Seattle Aircraft Certification Office (ACO),
FAA, has the authority to approve AMOCs for this AD, if requested in
accordance with the procedures found in 14 CFR 39.19.
Issued in Renton, Washington, on May 9, 2005.
Jeffrey E. Duven,
Acting Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. 05-9872 Filed 5-17-05; 8:45 am]
BILLING CODE 4910-13-P