Airworthiness Directives; Airbus Model A300 B2 and B4 Series Airplanes, 17347-17349 [05-6768]

Download as PDF Federal Register / Vol. 70, No. 65 / Wednesday, April 6, 2005 / Proposed Rules Unsafe Condition DEPARTMENT OF TRANSPORTATION (d) This AD was prompted by a report that bushings were installed in accordance with improper procedures in the structural repair manual. We are issuing this AD to detect and correct improperly installed bushings which could result in reduced tensile strength of the reinforcing strap of the wing’s lower skin, and consequently a reduction of the structural capability of the wing and possible wing failure. Compliance (e) You are responsible for having the actions required by this AD performed within the compliance times specified, unless the actions have already been done. Inspection and Corrective Actions (f) Within 12 months or 3,000 flight cycles after the effective date of this AD, whichever occurs first, do a detailed inspection of the reinforcing strap of the left- and right-hand wings’ lower skin at WS 2635 for improperly installed bushings in accordance with the Accomplishment Instructions of Fokker Service Bulletin F28/57–93, dated December 22, 2003. Note 1: For the purposes of this AD, a detailed inspection is: ‘‘An intensive examination of a specific item, installation, or assembly to detect damage, failure, or irregularity. Available lighting is normally supplemented with a direct source of good lighting at an intensity deemed appropriate. Inspection aids such as mirror, magnifying lenses, etc., may be necessary. Surface cleaning and elaborate procedures may be required.’’ (1) If no improperly installed bushing is found, no further action is required by this AD. (2) If any improperly installed bushing is found, before further flight: (i) Repair the bushing in accordance with the Accomplishment Instructions of Fokker Service Bulletin F28/57–93, dated December 22, 2003; and (ii) Replace the reinforcing strap with a new reinforcing strap in accordance with the Accomplishment Instructions of Fokker Service Bulletin F28/57–96, dated December 22, 2003. Alternative Methods of Compliance (AMOCs) (g) The Manager, International Branch, ANM–116, Transport Airplane Directorate, FAA, has the authority to approve AMOCs for this AD, if requested in accordance with the procedures found in 14 CFR 39.19. Related Information (h) Dutch airworthiness directive 2004– 021, dated February 27, 2004, also addresses the subject of this AD. Issued in Renton, Washington, on March 25, 2005. Ali Bahrami, Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. 05–6760 Filed 4–5–05; 8:45 am] BILLING CODE 4910–13–P VerDate jul<14>2003 17:48 Apr 05, 2005 Jkt 205001 Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2005–20861; Directorate Identifier 2005–NM–020–AD] RIN 2120–AA64 Airworthiness Directives; Airbus Model A300 B2 and B4 Series Airplanes Federal Aviation Administration (FAA), Department of Transportation (DOT). ACTION: Notice of proposed rulemaking (NPRM). AGENCY: SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) for certain Airbus Model A300 B2 and B4 series airplanes. This proposed AD would require modifying the wiring of the autopilot pitch torque limiter switch. This proposed AD is prompted by several reports of pitch trim disconnect caused by insufficient length in the wiring to the pitch torque limiter lever. We are proposing this AD to prevent possible trim loss when the flightcrew tries to override the autopilot pitch control, which could result in uncontrolled flight of the airplane. DATES: We must receive comments on this proposed AD by May 6, 2005. ADDRESSES: Use one of the following addresses to submit comments on this proposed AD. • DOT Docket Web site: Go to https://dms.dot.gov and follow the instructions for sending your comments electronically. • Government-wide rulemaking Web site: Go to https://www.regulations.gov and follow the instructions for sending your comments electronically. • Mail: Docket Management Facility, U.S. Department of Transportation, 400 Seventh Street SW., Nassif Building, room PL–401, Washington, DC 20590. • By fax: (202) 493–2251. • Hand Delivery: Room PL–401 on the plaza level of the Nassif Building, 400 Seventh Street SW., Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. For service information identified in this proposed AD, contact Jacques Leborgne, Airbus Customer Service Directorate, 1 Rond Point Maurice Bellonte, 31707 Blagnac Cedex, France; fax (+33) 5 61 93 36 14. You can examine the contents of this AD docket on the Internet at https:// dms.dot.gov, or in person at the Docket Management Facility, U.S. Department of Transportation, 400 Seventh Street SW., room PL–401, on the plaza level of PO 00000 Frm 00008 Fmt 4702 Sfmt 4702 17347 the Nassif Building, Washington, DC. This docket number is FAA–2005– 20861; the directorate identifier for this docket is 2005–NM–020–AD. FOR FURTHER INFORMATION CONTACT: Rosanne Ryburn, Aerospace Engineer, International Branch, ANM–116, FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington 98055–4056; telephone (425) 227–2139; fax (425) 227–1149. SUPPLEMENTARY INFORMATION: Comments Invited We invite you to submit any relevant written data, views, or arguments regarding this proposed AD. Send your comments to an address listed under ADDRESSES. Include ‘‘Docket No. FAA– 2005–20861; Directorate Identifier 2005–NM–020–AD’’ at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of the proposed AD. We will consider all comments submitted by the closing date and may amend the proposed AD in light of those comments. We will post all comments we receive, without change, to https:// dms.dot.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact with FAA personnel concerning this proposed AD. Using the search function of our docket website, anyone can find and read the comments in any of our dockets, including the name of the individual who sent the comment (or signed the comment on behalf of an association, business, labor union, etc.). You can review the DOT’s complete Privacy Act Statement in the Federal Register published on April 11, 2000 (65 FR 19477–78), or you can visit https:// dms.dot.gov. Examining the Docket You can examine the AD docket on the Internet at https://dms.dot.gov, or in person at the Docket Management Facility office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The Docket Management Facility office (telephone (800) 647–5227) is located on the plaza level of the Nassif Building at the DOT street address stated in the ADDRESSES section. Comments will be available in the AD docket shortly after the DMS receives them. Discussion ´ ´ The Direction Generale de l’Aviation Civile (DGAC), which is the airworthiness authority for France, E:\FR\FM\06APP1.SGM 06APP1 17348 Federal Register / Vol. 70, No. 65 / Wednesday, April 6, 2005 / Proposed Rules notified us that an unsafe condition may exist on certain Airbus Model A300 B2 and B4 series airplanes. The DGAC advises of several reports of pitch trim disconnect caused by insufficient length in the wiring to the pitch torque limiter lever. The DGAC also advises of possible trim loss when the flightcrew tries to override the autopilot pitch control. Possible trim loss, if not corrected, could result in uncontrolled flight of the airplane. Relevant Service Information Airbus has issued Service Bulletin A300–22–0117, dated September 7, 2004. The service bulletin describes procedures for modifying the wiring of the autopilot pitch torque limiter switch. For certain airplanes, modification includes installing new clamps and harnesses. For certain other airplanes, modification includes the following: • Modifying the equipment and wiring in the left-hand electronics rack 80VU. • Modifying the equipment and wiring in relay box 103VU. • Modifying the wiring between the left-hand rack 80VU and relay box 103VU. • Modifying the wiring between the rudder and the upper half of the fuselage. Accomplishing the actions specified in the service information is intended to adequately address the unsafe condition. The DGAC mandated the service information and issued French airworthiness directive F–2004–186, dated November 24, 2004, to ensure the continued airworthiness of these airplanes in France. FAA’s Determination and Requirements of the Proposed AD These airplane models are manufactured in France and are type certificated for operation in the United States under the provisions of § 21.29 of the Federal Aviation Regulations (14 CFR 21.29) and the applicable bilateral airworthiness agreement. Pursuant to this bilateral airworthiness agreement, the DGAC has kept the FAA informed of the situation described above. We have examined the DGAC’s findings, evaluated all pertinent information, and determined that we need to issue an AD for products of this type design that are certificated for operation in the United States. Therefore, we are proposing this AD, which would require accomplishing the actions specified in the service information described previously. VerDate jul<14>2003 15:58 Apr 05, 2005 Jkt 205001 Costs of Compliance This proposed AD would affect about 20 airplanes of U.S. registry. The proposed actions would take about between 8 and 11 work hours per airplane, depending on airplane configuration, at an average labor rate of $65 per work hour. Required parts would cost about $1,840 and $4,280 per airplane, depending on airplane configuration. Based on these figures, the estimated cost of the proposed AD for U.S. operators is between $47,200 and $99,900, or between $2,360 and $4,995 per airplane. Authority for This Rulemaking Title 49 of the United States Code specifies the FAA’s authority to issue rules on aviation safety. Subtitle I, Section 106, describes the authority of the FAA Administrator. Subtitle VII, Aviation Programs, describes in more detail the scope of the Agency’s authority. We are issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701, ‘‘General requirements.’’ Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. Regulatory Findings We have determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government. For the reasons discussed above, I certify that the proposed regulation: 1. Is not a ‘‘significant regulatory action’’ under Executive Order 12866; 2. Is not a ‘‘significant rule’’ under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and 3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. We prepared a regulatory evaluation of the estimated costs to comply with this proposed AD. See the ADDRESSES section for a location to examine the regulatory evaluation. PO 00000 Frm 00009 Fmt 4702 Sfmt 4702 List of Subjects in 14 CFR Part 39 Air transportation, Aircraft, Aviation safety, Safety. The Proposed Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows: PART 39—AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. § 39.13 [Amended] 2. The FAA amends § 39.13 by adding the following new airworthiness directive (AD): Airbus: Docket No. FAA–2005–20861; Directorate Identifier 2005–NM–020–AD. Comments Due Date (a) The Federal Aviation Administration must receive comments on this AD action by May 6, 2005. Affected ADs (b) None. Applicability (c) This AD applies to Airbus Model A300 B2 and B4 series airplanes, certificated in any category; as identified in Airbus Service Bulletin A300–22–0117, dated September 7, 2004. Unsafe Condition (d) This AD was prompted by several reports of pitch trim disconnect caused by insufficient length in the wiring to the pitch torque limiter lever. We are issuing this AD to prevent possible trim loss when the flightcrew tries to override the autopilot pitch control, which could result in uncontrolled flight of the airplane. Compliance (e) You are responsible for having the actions required by this AD performed within the compliance times specified, unless the actions have already been done. Modification (f) Within 20 months after the effective date of this AD, modify the wiring of the autopilot pitch torque limiter switch, by doing all of the applicable actions specified in the Accomplishment Instructions of Airbus Service Bulletin A300–22–0117, dated September 7, 2004. Alternative Methods of Compliance (AMOCs) (g) The Manager, International Branch, ANM–116, Transport Airplane Directorate, FAA, has the authority to approve AMOCs for this AD, if requested in accordance with the procedures found in 14 CFR 39.19. E:\FR\FM\06APP1.SGM 06APP1 Federal Register / Vol. 70, No. 65 / Wednesday, April 6, 2005 / Proposed Rules Related Information (h) French airworthiness directive F–2004– 186, dated November 24, 2004, also addresses the subject of this AD. Issued in Renton, Washington, on March 30, 2005. Kalene C. Yanamura, Acting Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. 05–6768 Filed 4–5–05; 8:45 am] BILLING CODE 4910–13–P DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA–2005–20872; Directorate Identifier 2004–NM–271–AD] RIN 2120–AA64 Airworthiness Directives; Learjet Model 23, 24, 24A, 24B, 24B–A, 24C, 24D, 24D–A, 24E, 24F, 24F–A, 25, 25A, 25B, 25C, 25D, 25F, 28, 29, 31, 31A, 35, 35A (C–21A), and 36 Airplanes Federal Aviation Administration (FAA), Department of Transportation (DOT). ACTION: Notice of proposed rulemaking (NPRM). AGENCY: SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) for certain Learjet Model 23, 24, 24A, 24B, 24B–A, 24C, 24D, 24D–A, 24E, 24F, 24F–A, 25, 25A, 25B, 25C, 25D, 25F, 28, 29, 31, 31A, 35, 35A (C–21A), and 36 airplanes. This proposed AD would require a one-time inspection of the center ball of the aileron control cable or cables for a defective swage, and corrective actions if necessary. This proposed AD is prompted by a report indicating that an aileron cable failed on one affected airplane when the cable underwent a tension check. We are proposing this AD to prevent severe weakening of the aileron cable, and consequent reduced controllability of the airplane. DATES: We must receive comments on this proposed AD by May 23, 2005. ADDRESSES: Use one of the following addresses to submit comments on this proposed AD. • DOT Docket Web site: Go to https://dms.dot.gov and follow the instructions for sending your comments electronically. • Government-wide rulemaking web site: Go to https://www.regulations.gov and follow the instructions for sending your comments electronically. • Mail: Docket Management Facility, U.S. Department of Transportation, 400 Seventh Street SW., Nassif Building, room PL–401, Washington, DC 20590. • By fax: (202) 493–2251. • Hand Delivery: Room PL–401 on the plaza level of the Nassif Building, 400 Seventh Street SW., Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. For service information identified in this proposed AD, contact Learjet, Inc., One Learjet Way, Wichita, Kansas 67209–2942. You can examine the contents of this AD docket on the Internet at https:// dms.dot.gov, or in person at the Docket Management Facility, U.S. Department of Transportation, 400 Seventh Street SW., room PL–401, on the plaza level of the Nassif Building, Washington, DC. This docket number is FAA–2005– 20872; the directorate identifier for this docket is 2004–NM–271–AD. FOR FURTHER INFORMATION CONTACT: David Hirt, Aerospace Engineer, Systems and Propulsion Branch, ACE– 116W, FAA, Wichita Aircraft Certification Office, 1801 Airport Road, Room 100, Mid-Continent Airport, Wichita, Kansas 67209; telephone (316) 946–4156; fax (316) 946–4107. SUPPLEMENTARY INFORMATION: Comments Invited We invite you to submit any relevant written data, views, or arguments regarding this proposed AD. Send your comments to an address listed under ADDRESSES. Include ‘‘Docket No. FAA– 2005–20872; Directorate Identifier 2004–NM–271–AD’’ in the subject line of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of the proposed AD. We will consider all comments submitted by the closing date and may amend the proposed AD in light of those comments. We will post all comments we receive, without change, to https:// dms.dot.gov, including any personal information you provide. We will also 17349 post a report summarizing each substantive verbal contact with FAA personnel concerning this proposed AD. Using the search function of that website, anyone can find and read the comments in any of our dockets, including the name of the individual who sent the comment (or signed the comment on behalf of an association, business, labor union, etc.). You can review DOT’s complete Privacy Act Statement in the Federal Register published on April 11, 2000 (65 FR 19477–78), or you can visit https:// dms.dot.gov. Examining the Docket You can examine the AD docket on the Internet at https://dms.dot.gov, or in person at the Docket Management Facility office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The Docket Management Facility office (telephone (800) 647–5227) is located on the plaza level of the Nassif Building at the DOT street address stated in the ADDRESSES section. Comments will be available in the AD docket shortly after the DMS receives them. Discussion We have received a report indicating that an aileron cable failed on a Learjet Model 35A (C–21A) airplane when the cable underwent a tension check while being installed. Further investigation showed that an over-sized ball was swaged onto the cable during manufacture. Swaging an over-sized ball onto a cable allows excess material into the swaging die, which causes the ball to over-swage and then sever the cable strands. This condition, if not corrected, could result in severe weakening of the aileron cable, and consequent reduced controllability of the airplane. The subject area on Learjet Model 23, 24, 24A, 24B, 24B–A, 24C, 24D, 24D–A, 24E, 24F, 24F–A, 25, 25A, 25B, 25C, 25D, 25F, 28, 29, 31, 31A, 35, and 36 airplanes is identical to those on the affected Model 35A (C–21A) airplane. Therefore, all these airplanes may be subject to the same unsafe condition. Relevant Service Information We have reviewed the Learjet service bulletins in the following table. LEARJET SERVICE BULLETINS Alert service bulletin Date Model A23/24/25–27–17 ...... December 23, 2002 ................ A28/29–27–24 ........... December 23, 2002 ................ 23, 24, 24A, 24B, 24B–A, 24C, 24D, 24D–A, 24E, 24F, 24F–A, 25, 25A, 25B, 25C, 25D, and 25F. 28 and 29. VerDate jul<14>2003 17:48 Apr 05, 2005 Jkt 205001 PO 00000 Frm 00010 Fmt 4702 Sfmt 4702 E:\FR\FM\06APP1.SGM 06APP1

Agencies

[Federal Register Volume 70, Number 65 (Wednesday, April 6, 2005)]
[Proposed Rules]
[Pages 17347-17349]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 05-6768]


-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. FAA-2005-20861; Directorate Identifier 2005-NM-020-AD]
RIN 2120-AA64


Airworthiness Directives; Airbus Model A300 B2 and B4 Series 
Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of 
Transportation (DOT).

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) 
for certain Airbus Model A300 B2 and B4 series airplanes. This proposed 
AD would require modifying the wiring of the autopilot pitch torque 
limiter switch. This proposed AD is prompted by several reports of 
pitch trim disconnect caused by insufficient length in the wiring to 
the pitch torque limiter lever. We are proposing this AD to prevent 
possible trim loss when the flightcrew tries to override the autopilot 
pitch control, which could result in uncontrolled flight of the 
airplane.

DATES: We must receive comments on this proposed AD by May 6, 2005.

ADDRESSES: Use one of the following addresses to submit comments on 
this proposed AD.
     DOT Docket Web site: Go to https://dms.dot.gov and follow 
the instructions for sending your comments electronically.
     Government-wide rulemaking Web site: Go to https://
www.regulations.gov and follow the instructions for sending your 
comments electronically.
     Mail: Docket Management Facility, U.S. Department of 
Transportation, 400 Seventh Street SW., Nassif Building, room PL-401, 
Washington, DC 20590.
     By fax: (202) 493-2251.
     Hand Delivery: Room PL-401 on the plaza level of the 
Nassif Building, 400 Seventh Street SW., Washington, DC, between 9 a.m. 
and 5 p.m., Monday through Friday, except Federal holidays.
    For service information identified in this proposed AD, contact 
Jacques Leborgne, Airbus Customer Service Directorate, 1 Rond Point 
Maurice Bellonte, 31707 Blagnac Cedex, France; fax (+33) 5 61 93 36 14.
    You can examine the contents of this AD docket on the Internet at 
https://dms.dot.gov, or in person at the Docket Management Facility, 
U.S. Department of Transportation, 400 Seventh Street SW., room PL-401, 
on the plaza level of the Nassif Building, Washington, DC. This docket 
number is FAA-2005-20861; the directorate identifier for this docket is 
2005-NM-020-AD.

FOR FURTHER INFORMATION CONTACT: Rosanne Ryburn, Aerospace Engineer, 
International Branch, ANM-116, FAA, Transport Airplane Directorate, 
1601 Lind Avenue, SW., Renton, Washington 98055-4056; telephone (425) 
227-2139; fax (425) 227-1149.

SUPPLEMENTARY INFORMATION:

Comments Invited

    We invite you to submit any relevant written data, views, or 
arguments regarding this proposed AD. Send your comments to an address 
listed under ADDRESSES. Include ``Docket No. FAA-2005-20861; 
Directorate Identifier 2005-NM-020-AD'' at the beginning of your 
comments. We specifically invite comments on the overall regulatory, 
economic, environmental, and energy aspects of the proposed AD. We will 
consider all comments submitted by the closing date and may amend the 
proposed AD in light of those comments.
    We will post all comments we receive, without change, to https://
dms.dot.gov, including any personal information you provide. We will 
also post a report summarizing each substantive verbal contact with FAA 
personnel concerning this proposed AD. Using the search function of our 
docket website, anyone can find and read the comments in any of our 
dockets, including the name of the individual who sent the comment (or 
signed the comment on behalf of an association, business, labor union, 
etc.). You can review the DOT's complete Privacy Act Statement in the 
Federal Register published on April 11, 2000 (65 FR 19477-78), or you 
can visit https://dms.dot.gov.

Examining the Docket

    You can examine the AD docket on the Internet at https://
dms.dot.gov, or in person at the Docket Management Facility office 
between 9 a.m. and 5 p.m., Monday through Friday, except Federal 
holidays. The Docket Management Facility office (telephone (800) 647-
5227) is located on the plaza level of the Nassif Building at the DOT 
street address stated in the ADDRESSES section. Comments will be 
available in the AD docket shortly after the DMS receives them.

Discussion

    The Direction G[eacute]n[eacute]rale de l'Aviation Civile (DGAC), 
which is the airworthiness authority for France,

[[Page 17348]]

notified us that an unsafe condition may exist on certain Airbus Model 
A300 B2 and B4 series airplanes. The DGAC advises of several reports of 
pitch trim disconnect caused by insufficient length in the wiring to 
the pitch torque limiter lever. The DGAC also advises of possible trim 
loss when the flightcrew tries to override the autopilot pitch control. 
Possible trim loss, if not corrected, could result in uncontrolled 
flight of the airplane.

Relevant Service Information

    Airbus has issued Service Bulletin A300-22-0117, dated September 7, 
2004. The service bulletin describes procedures for modifying the 
wiring of the autopilot pitch torque limiter switch. For certain 
airplanes, modification includes installing new clamps and harnesses. 
For certain other airplanes, modification includes the following:
     Modifying the equipment and wiring in the left-hand 
electronics rack 80VU.
     Modifying the equipment and wiring in relay box 103VU.
     Modifying the wiring between the left-hand rack 80VU and 
relay box 103VU.
     Modifying the wiring between the rudder and the upper half 
of the fuselage.
    Accomplishing the actions specified in the service information is 
intended to adequately address the unsafe condition. The DGAC mandated 
the service information and issued French airworthiness directive F-
2004-186, dated November 24, 2004, to ensure the continued 
airworthiness of these airplanes in France.

FAA's Determination and Requirements of the Proposed AD

    These airplane models are manufactured in France and are type 
certificated for operation in the United States under the provisions of 
Sec.  21.29 of the Federal Aviation Regulations (14 CFR 21.29) and the 
applicable bilateral airworthiness agreement. Pursuant to this 
bilateral airworthiness agreement, the DGAC has kept the FAA informed 
of the situation described above. We have examined the DGAC's findings, 
evaluated all pertinent information, and determined that we need to 
issue an AD for products of this type design that are certificated for 
operation in the United States.
    Therefore, we are proposing this AD, which would require 
accomplishing the actions specified in the service information 
described previously.

Costs of Compliance

    This proposed AD would affect about 20 airplanes of U.S. registry. 
The proposed actions would take about between 8 and 11 work hours per 
airplane, depending on airplane configuration, at an average labor rate 
of $65 per work hour. Required parts would cost about $1,840 and $4,280 
per airplane, depending on airplane configuration. Based on these 
figures, the estimated cost of the proposed AD for U.S. operators is 
between $47,200 and $99,900, or between $2,360 and $4,995 per airplane.

Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to 
issue rules on aviation safety. Subtitle I, Section 106, describes the 
authority of the FAA Administrator. Subtitle VII, Aviation Programs, 
describes in more detail the scope of the Agency's authority.
    We are issuing this rulemaking under the authority described in 
Subtitle VII, Part A, Subpart III, Section 44701, ``General 
requirements.'' Under that section, Congress charges the FAA with 
promoting safe flight of civil aircraft in air commerce by prescribing 
regulations for practices, methods, and procedures the Administrator 
finds necessary for safety in air commerce. This regulation is within 
the scope of that authority because it addresses an unsafe condition 
that is likely to exist or develop on products identified in this 
rulemaking action.

Regulatory Findings

    We have determined that this proposed AD would not have federalism 
implications under Executive Order 13132. This proposed AD would not 
have a substantial direct effect on the States, on the relationship 
between the national Government and the States, or on the distribution 
of power and responsibilities among the various levels of government.
    For the reasons discussed above, I certify that the proposed 
regulation:
    1. Is not a ``significant regulatory action'' under Executive Order 
12866;
    2. Is not a ``significant rule'' under the DOT Regulatory Policies 
and Procedures (44 FR 11034, February 26, 1979); and
    3. Will not have a significant economic impact, positive or 
negative, on a substantial number of small entities under the criteria 
of the Regulatory Flexibility Act.
    We prepared a regulatory evaluation of the estimated costs to 
comply with this proposed AD. See the ADDRESSES section for a location 
to examine the regulatory evaluation.

List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Safety.

The Proposed Amendment

    Accordingly, under the authority delegated to me by the 
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

    1. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.


Sec.  39.13  [Amended]

    2. The FAA amends Sec.  39.13 by adding the following new 
airworthiness directive (AD):

Airbus: Docket No. FAA-2005-20861; Directorate Identifier 2005-NM-
020-AD.

Comments Due Date

    (a) The Federal Aviation Administration must receive comments on 
this AD action by May 6, 2005.

Affected ADs

    (b) None.

Applicability

    (c) This AD applies to Airbus Model A300 B2 and B4 series 
airplanes, certificated in any category; as identified in Airbus 
Service Bulletin A300-22-0117, dated September 7, 2004.

Unsafe Condition

    (d) This AD was prompted by several reports of pitch trim 
disconnect caused by insufficient length in the wiring to the pitch 
torque limiter lever. We are issuing this AD to prevent possible 
trim loss when the flightcrew tries to override the autopilot pitch 
control, which could result in uncontrolled flight of the airplane.

Compliance

    (e) You are responsible for having the actions required by this 
AD performed within the compliance times specified, unless the 
actions have already been done.

Modification

    (f) Within 20 months after the effective date of this AD, modify 
the wiring of the autopilot pitch torque limiter switch, by doing 
all of the applicable actions specified in the Accomplishment 
Instructions of Airbus Service Bulletin A300-22-0117, dated 
September 7, 2004.

Alternative Methods of Compliance (AMOCs)

    (g) The Manager, International Branch, ANM-116, Transport 
Airplane Directorate, FAA, has the authority to approve AMOCs for 
this AD, if requested in accordance with the procedures found in 14 
CFR 39.19.

[[Page 17349]]

Related Information

    (h) French airworthiness directive F-2004-186, dated November 
24, 2004, also addresses the subject of this AD.


    Issued in Renton, Washington, on March 30, 2005.
Kalene C. Yanamura,
Acting Manager, Transport Airplane Directorate, Aircraft Certification 
Service.
[FR Doc. 05-6768 Filed 4-5-05; 8:45 am]
BILLING CODE 4910-13-P
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.