[Federal Register: October 31, 2008 (Volume 73, Number 212)] [Rules and Regulations] [Page 64876-64879] From the Federal Register Online via GPO Access [wais.access.gpo.gov] [DOCID:fr31oc08-6] ----------------------------------------------------------------------- DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA-2007-27628; Directorate Identifier 2007-CE-025-AD; Amendment 39-15713; AD 2007-07-06 R1] RIN 2120-AA64 Airworthiness Directives; Cessna Aircraft Company (Type Certificate Previously Held by Columbia Aircraft Manufacturing) Models LC40-550FG, LC41-550FG, and LC42-550FG Airplanes AGENCY: Federal Aviation Administration (FAA), Department of Transportation (DOT). ACTION: Final rule. ----------------------------------------------------------------------- SUMMARY: We are adopting a new airworthiness directive (AD) to revise AD 2007-07-06, which applies to certain Cessna Aircraft Company (type certificate previously held by Columbia Aircraft Manufacturing) (Cessna) Models LC40-550FG, LC41-550FG, and LC42-550FG airplanes. AD 2007-07-06 currently requires the following: Adding information to the limitations section of [[Page 64877]] the airplane flight manual (AFM); repetitively inspecting the aileron and the elevator linear bearings and control rods for foreign object debris, scarring, or damage; and taking all necessary corrective actions. Since we issued AD 2007-07-06, Cessna has issued a new service bulletin that contains procedures for installing an access panel to facilitate the required inspections. Consequently, this AD retains the actions currently required in AD 2007-07-06; allows installing access panels; and changes the serial number applicability. We are issuing this AD to prevent jamming in the aileron and elevator control systems, which could result in failure. This failure could lead to loss of control. DATES: This AD becomes effective on December 5, 2008. On December 5, 2008, the Director of the Federal Register approved the incorporation by reference of Cessna Mandatory Service Bulletin SB- 07-002D, dated May 29, 2008, and Cessna Mandatory Service Bulletin SB- 07-018, dated May 29, 2008, listed in this AD. As of April 9, 2007 (72 FR 15822, April 3, 2007), the Director of the Federal Register approved the incorporation by reference of Columbia Mandatory Service Bulletin SB-07-002, dated March 14, 2007, listed in this AD. ADDRESSES: For service information identified in this AD, contact Cessna Aircraft Company, Product Support, P.O. Box 7706, Wichita, Kansas 67227; phone (316) 517-5800; fax: (316) 942-9006. To view the AD docket, go to U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC 20590, or on the Internet at http://www.regulations.gov. The docket number is FAA-2007-27628; Directorate Identifier 2007-CE-025-AD. FOR FURTHER INFORMATION CONTACT: Jeff Morfitt, Aerospace Engineer, FAA, Seattle Aircraft Certification Office, 1601 Lind Avenue, SW., Renton, WA 98057; telephone: (425) 917-6405; fax: (425) 917-6590; jeff.morfitt@faa.gov. SUPPLEMENTARY INFORMATION: Discussion On August 1, 2008, we issued a proposal to amend part 39 of the Federal Aviation Regulations (14 CFR part 39) to include an AD that would apply to certain Cessna Models LC40-550FG, LC41-550FG, and LC42- 550FG airplanes. This proposal was published in the Federal Register as a notice of proposed rulemaking (NPRM) on August 7, 2008 (73 FR 45902). The NPRM proposed to revise AD 2007-07-06 with a new AD that will retain the actions currently required in AD 2007-07-06; allow installing access panels; and change the serial number applicability. Comments We provided the public the opportunity to participate in developing this AD. We received no comments on the proposal or on the determination of the cost to the public. Conclusion We have carefully reviewed the available data and determined that air safety and the public interest require adopting the AD as proposed except for minor editorial corrections. We have determined that these minor corrections: Are consistent with the intent that was proposed in the NPRM for correcting the unsafe condition; and Do not add any additional burden upon the public than was already proposed in the NPRM. Costs of Compliance We estimate that this AD affects 1,495 airplanes in the U.S. registry. We estimate the following costs to do the inspection: ---------------------------------------------------------------------------------------------------------------- Total cost Labor cost Parts cost Total cost on U.S. per airplane operators ---------------------------------------------------------------------------------------------------------------- 4 work-hours x $80 per hour = $320.............. Not applicable.................... $320 $478,400 ---------------------------------------------------------------------------------------------------------------- We estimate the following costs to do the optional access panel installation: ------------------------------------------------------------------------ Total cost Labor cost Parts cost per airplane ------------------------------------------------------------------------ 14 work-hours x $80 per hour = Not applicable....... $1,120 $1,120. ------------------------------------------------------------------------ Warranty credit for installing the access panel may be given to the extent noted in Cessna Mandatory Service Bulletins SB-07-018, dated May 29, 2008. Authority for This Rulemaking Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106 describes the authority of the FAA Administrator. Subtitle VII, Aviation Programs, describes in more detail the scope of the agency's authority. We are issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, section 44701, ``General requirements.'' Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this AD. Regulatory Findings We have determined that this AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government. For the reasons discussed above, I certify that this AD: 1. Is not a ``significant regulatory action'' under Executive Order 12866; 2. Is not a ``significant rule'' under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and 3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. We prepared a summary of the costs to comply with this AD (and other [[Page 64878]] information as included in the Regulatory Evaluation) and placed it in the AD Docket. You may get a copy of this summary by sending a request to us at the address listed under ADDRESSES. Include ``Docket No. FAA- 2007-27628; Directorate Identifier 2007-CE-025-AD'' in your request. List of Subjects in 14 CFR Part 39 Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety. Adoption of the Amendment 0 Accordingly, under the authority delegated to me by the Administrator, the Federal Aviation Administration amends part 39 of the Federal Aviation Regulations (14 CFR part 39) as follows: PART 39--AIRWORTHINESS DIRECTIVES 0 1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. Sec. 39.13 [Amended] 0 2. The FAA amends Sec. 39.13 by removing Airworthiness Directive (AD) 2007-07-06, Amendment 39-15011 (72 FR 15822, April 3, 2007), and adding the following new AD: 2007-07-06 R1 Cessna Aircraft Company (type certificate previously held by Columbia Aircraft Manufacturing): Amendment 39-15713; Docket No. FAA-2007-27628; Directorate Identifier 2007-CE-025-AD. Effective Date (a) This AD becomes effective on December 5, 2008. Affected ADs (b) This AD revises AD 2007-07-06, Amendment 39-15011. Applicability (c) This AD applies to the following airplane models and serial numbers that are certificated in any category: ------------------------------------------------------------------------ Model Serial Nos. ------------------------------------------------------------------------ LC40-550FG............................ 40001 through 40079. LC41-550FG............................ 41001 through 41800 and 411001 through 411041. LC42-550FG............................ 42001 through 42569 and 421001 through 421006. ------------------------------------------------------------------------ Unsafe Condition (d) This AD is the result of reports of possible foreign object contamination of the linear bearings. We are issuing this AD to prevent jamming in the aileron and elevator control systems, which could result in failure. This failure could lead to loss of control. Compliance (e) To address this problem, you must do the following, unless already done: ------------------------------------------------------------------------ Actions Compliance Procedures ------------------------------------------------------------------------ (1) Insert Appendix A of Before further Under 14 CFR 43.7, Columbia Mandatory Service flight after April the owner/operator Bulletin SB-07-002, dated 9, 2007 (the holding at least a March 14, 2007, or Appendix compliance date private pilot A of Cessna Mandatory retained from AD certificate is Service Bulletin SB-07- 2007-07-06). allowed to do the 002D, dated May 29, 2008, AFM insertion into the limitations requirement of this section of the airplane AD. Make an entry flight manual (AFM). into the aircraft logbook showing compliance with this portion of the AD per compliance with 14 CFR 43.9. (2) Access and inspect the Initially inspect Following Columbia aileron bearings in both within the next 35 Mandatory Service wings and the elevator hours time-in- Bulletin SB-07-002, bearings in the fuselage service (TIS) after dated March 14, for foreign object debris. April 9, 2007 (the 2007, or Cessna compliance date Mandatory Service retained from AD Bulletin SB-07- 2007-07-06) 002D, dated May 29, Repetitively 2008, and FAA- inspect thereafter approved at intervals not to maintenance exceed 12 calendar procedures. The months. appropriate maintenance manual contains these procedures. (3) Remove any debris found Before further Following Columbia during any inspection flight after the Mandatory Service required in paragraph inspection in which Bulletin SB-07-002, (e)(2) of this AD. the debris is found. dated March 14, 2007, or Cessna Mandatory Service Bulletin SB-07- 002D, dated May 29, 2008, and FAA- approved maintenance procedures. The appropriate maintenance manual contains these procedures. (4) Inspect the aileron and Initially inspect Following Columbia elevator control rods for within the next 35 Mandatory Service scarring or damage near the hours TIS after Bulletin SB-07-002, linear bearings. April 9, 2007 (the dated March 14, compliance date 2007, or Cessna retained from AD Mandatory Service 2007-07-06). Bulletin SB-07- Repetitively 002D, dated May 29, inspect thereafter 2008, and FAA- at intervals not to approved exceed 12 calendar maintenance months. procedures. The appropriate maintenance manual contains these procedures. (5) Contact the manufacturer Make all repairs Following Columbia at the address specified in before further Mandatory Service paragraph (h)(3) of this AD flight after the Bulletin SB-07-002, for a repair scheme if any inspection in which dated March 14, scarring or damage is found scarring or damage 2007, or Cessna during any inspection is found. Mandatory Service required in paragraph Bulletin SB-07- (e)(4) of this AD. 002D, dated May 29, 2008, and FAA- approved maintenance procedures. The appropriate maintenance manual contains these procedures. (6) For the inspections At any time after Following Cessna required in paragraphs the effective date Mandatory Service (e)(2) and (e)(4) of this of this AD. Bulletin SB-07-018, AD, you may install a dated May 29, 2008. linear bearing access panel instead of drilling an inspection hole. If the hole has previously been drilled, the access panel may also be installed in addition to the inspection hole. ------------------------------------------------------------------------ [[Page 64879]] Note 1: Previous compliance with paragraphs (e)(1) through (e)(5) of this AD using Columbia Mandatory Service Bulletin SB-07- 002A, dated August 29, 2007; Cessna Mandatory Service Bulletin SB- 07-002B, dated December 10, 2007; or Cessna Mandatory Service Bulletin SB-07-002C, dated February 18, 2008, are acceptable methods of compliance. Note 2: Compliance with Cessna Mandatory Service Bulletin SB-07- 018, dated May 29, 2008, is not considered terminating action for this AD. This AD takes precedence over Cessna Mandatory Service Bulletin SB-07-018, dated May 29, 2008. Alternative Methods of Compliance (AMOCs) (f) The Manager, Seattle Aircraft Certification Office (ACO), FAA, ATTN: Jeff Morfitt, Aerospace Engineer, 1601 Lind Avenue, SW., Renton, WA 98057; telephone: (425) 917-6405; fax: (425) 917-6590, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO. (g) AMOCs approved for AD 2007-07-06 are approved for this AD. Material Incorporated by Reference (h) You must use Columbia Mandatory Service Bulletin SB-07-002, dated March 14, 2007, or Cessna Mandatory Service Bulletin SB-07- 002D, dated May 29, 2008, and Cessna Mandatory Service Bulletin SB- 07-018, page 1 dated May 29, 2008, pages 2 through 20 dated May 30, 2008, to do the actions required by this AD, unless the AD specifies otherwise. (1) The Director of the Federal Register approved the incorporation by reference of Cessna Mandatory Service Bulletin SB- 07-002D, dated May 29, 2008, and Cessna Mandatory Service Bulletin SB-07-018, page 1 dated May 29, 2008, pages 2 through 20 dated May 30, 2008, under 5 U.S.C. 552(a) and 1 CFR part 51. (2) On April 9, 2007 (72 FR 15822, April 3, 2007), the Director of the Federal Register approved the incorporation by reference of Columbia Mandatory Service Bulletin SB-07-002, dated March 14, 2007. (3) For service information identified in this AD, contact Cessna Aircraft Company, Product Support, P.O. Box 7706, Wichita, Kansas 67227. (4) You may review copies at the FAA, Central Region, Office of the Regional Counsel, 901 Locust, Kansas City, Missouri 64106; or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202- 741-6030, or go to: http://www.archives.gov/federal_register/code_ of_federal_regulations/ibr_locations.html. Issued in Kansas City, Missouri, on October 21, 2008. John Colomy, Acting Manager, Small Airplane Directorate, Aircraft Certification Service. [FR Doc. E8-25500 Filed 10-30-08; 8:45 am] BILLING CODE 4910-13-P
Justia Lawyer, Legal Aid & Services Directory: Business Lawyers